Ozito PFFP-65E Handleiding

Ozito Pomp PFFP-65E

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito PFFP-65E (8 pagina's) in de categorie Pomp. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

INSTRUCTION MANUAL

PFFP-65E

STANDARD EQUIPMENT

IN ORDER TO MAKE A CLAIM UNDER THIS

WARRANTY YOU MUST RETURN THE PRODUCT

TO YOUR NEAREST BUNNINGS WAREHOUSE WITH

YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO

RETURNING YOUR PRODUCT FOR WARRANTY

PLEASE TELEPHONE OUR CUSTOMER SERVICE

HELPLINE:

Australia 1800 069 486

New Zealand 0508 069 486

1 YEAR WARRANTY

Your product is guaranteed for a period of 12 months from the

original date of purchase and is intended for DIY (Do It Yourself)

use only. If a product is defective it will be repaired in accordance

with the terms of this warranty. Warranty excludes consumable

parts, for example: o-rings, bearing, seals, gaskets and adaptors.

WARNING

The following actions will result in the warranty being void.

• If the tool has been operated on a supply voltage other

than that speciﬁed on the tool.

• If the tool shows signs of damage or defects caused

by or resulting from abuse, accidents or alterations.

• Failure to perform maintenance as set out within the

instruction manual.

• If the tool is disassembled or tampered with in any way.

WARRANTY

TO ENSURE A SPEEDY RESPONSE PLEASE

HAVE THE MODEL NUMBER AND DATE OF

PURCHASE AVAILABLE. A CUSTOMER SERVICE

REPRESENTATIVE WILL TAKE YOUR CALL

AND ANSWER ANY QUESTIONS YOU MAY

HAVE RELATING TO THE WARRANTY POLICY

OR PROCEDURE.

OZITO Australia/New Zealand (Head Ofﬁce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.

The beneﬁts provided under this warranty are in addition

to other rights and remedies which are available to you at law.

Our goods come with guarantees that cannot be excluded

at law. You are entitled to a replacement or refund for a major

failure and for compensation for any other reasonably foreseeable

loss or damage. You are also entitled to have the goods repaired

or replaced if the goods fail to be of acceptable quality and the

failure does not amount to a major failure.

Generally you will be responsible for all costs associated with

a claim under this warranty, however, where you have suffered

any additional direct loss as a result of a defective product you

may be able to claim such expenses by contacting our customer

service helpline above.

PETROL

FIRE FIGHTING

PUMP

208CC 4 STROKE

SPECIFICATIONS

Engine: 4.8kW (6.5HP)

Engine Type: 4 Stroke, air cooled

Fuel Type: Unleaded petrol

Fuel Tank Capacity: 3.3L

Engine Capacity: 208cc

Max. Flow Rate: 11,500l/h

Max. Head: 70m

Max. Lift: 7m

Suction Inlet: 40mm (1½”)

Discharge Outlet: 2 x 25.4mm (1”), 1 x 40mm (1½”)

Weight: 29kg

5M Suction Hose

Fasteners & Adaptors

ozito.com.au

Spark Plug Wrench &

Filter

Petrol Pump

0618

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to

the online manual.

1. CONNECTING THE INLET

WARNING! ENSURE THE ENGINE IS SHUT OFF BEFORE

PERFORMING ANY OF THE FOLLOWING ASSEMBLY.

Connecting the Suction Inlet

Removing the Protection Covers

1. Placethelter

assembly into the

intake end of the

5m suction hose

and secure with a

hose clamp tightly.

2. Insert a hose

adaptor and an

o-ring into one of

the collars and

fasten to the outlet

side of the 5m

suction hose using

a hose clamp.

3. Screw the hose adaptor and

collar tightly onto the pumps

suction inlet in a clockwise

direction to secure in place.

Note: Teontape(notsupplied)is

recommended on threads

to ensure a water tight seal

and prevent any leakage.

Theinletallowsfora40mm(1½”)supplylinetobeconnected

and is capable of a maximum suction height of 7m.

Thepumpinletandoutletshavebeenttedwithaprotection

cover for transportation. These will need to be removed before

connecting any pipes.

CAUTION: AVOID POSITIONING THE INLET PIPE HIGHER

THAN THE PUMP, AS THIS WOULD DELAY THE ESCAPE

OF AIR BUBBLES FROM THE INLET PIPE.

CAUTION: THE INPUT HOSE OR PIPE SHOULD BE LOW

ENOUGH IN THE WATER TO ENSURE THAT IF THE

WATER LEVEL FALLS, THE PUMP WILL NOT RUN DRY.

ENSURE THAT THIS IS CHECKED WHEN IN OPERATION.

16. Spark Plug Wrench

17. Filter

18. 5m Suction Hose

19. Collars

20. O-rings

21. Outlet Caps

22. Hose Adaptors

23. Hose Clamps

KNOW YOUR PRODUCT SETUP & PREPARATION

PETROL FIRE FIGHTING WATER PUMP

ACCESSORIES

16 17 18 19 20 21 22 23

1. Exhaust

2. Air Filter

3. Choke Lever

4. Fuel Lever

5. Recoil Starter

6. Fuel Cap

7. Fuel Tank

8. Throttle Lever

9. Motor Housing

10. Priming Cap

11. Discharge Outlet

12. Pump Housing

13. Suction Inlet

14. Drain Screw

15. Oil Fill Plug

INSTALLATION

Connecting the Discharge Outlet

1. Insert a hose

adaptor and an

o-ring into one of

the collars.

2. Screw the hose adaptor and

collar tightly onto one of the

pump outlets in a clockwise

direction to secure in place.

Note: Teontape(notsupplied)

is recommended on

threads to ensure a water

tight seal and prevent any

leakage.

3. Repeatthisprocesstotmultipleoutlets.

Ensureunusedoutletsarettedwiththesuppliedoutletcaps

to stop water from expelling out of the discharge outlets.

Theoutletallowsfora25.4mm(1”)and40mm(1½”)pipetobe

connected and is capable of a maximum head of 70m.

Thepumphas3outlets(2x25.4mmand1x40mm),

which allows for multiple outlets to be used to pump water

simultaneously,howeverthiswillresultinlowerpressureand

owrate.

2. CONNECTING THE OUTLET

NOTE: TO USE THE PUMP IN PERMANENT INSTALLATIONS

WITH RIGID PIPES, INSTALL A NON-RETURN VALVE TO AVOID

THE FLUID BEING RE-CIRCULATED ONCE THE PUMP HAS

STOPPED.

CAUTION: ALL CONNECTIONS MUST BE AIR TIGHT,

FAILURE TO DO SO MAY RESULT IN AN AIR LEAK

WHICH CAN PREVENT THE PUMP FROM PRIMING.

1. Ensure the pump is mounted to a rigid base or ground.

70m

MAXIMUM DELIVERY HEIGHT

WATER LEVEL

CAUTION: ALWAYS CARRY OR LIFT THE PUMP BY THE

FRAME TO AVOID DAMAGING THE UNIT.

CAUTION: THIS PRODUCT IS INTENDED FOR PUMPING

WATER IN A HOME DOMESTIC APPLICATION. DO NOT

USE IT FOR CORROSIVE, ABRASIVE, EXPLOSIVE OR

DANGEROUS LIQUIDS.

2. Ensure the distance from the surface of the water to the

pump inlet does not exceed 7m.

3. Ensure the distance from the pump to the highest point that

you wish to deliver the water does not exceed 70 metres.

Before starting, perform a few simple checks:

WARNING! ENSURE THE OUTLET FOR THIS PUMP, INCLUDING

ANY HOSES OR PIPES ARE NOT RESTRICTED OR OBSTRUCTED

IN ANY WAY. TAPS, VALVES AND ANY TYPE OF TRIGGER

NOZZLE MUST NEVER BE USED WITH THIS PUMP. FAILURE TO

FOLLOW THESE INSTRUCTIONS MAY RESULT IN PUMP FAILURE

OR SERIOUS INJURY.

Product specificaties

Merk:	Ozito
Categorie:	Pomp
Model:	PFFP-65E

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito PFFP-65E stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Pomp Ozito

Ozito CPPAS-800 Handleiding

12 Juni 2023

Ozito CPP-802 Handleiding

31 Mei 2023

Ozito PTP-425 Handleiding

21 Mei 2023

Ozito PSDW-750 Handleiding

29 April 2023

Ozito TPIK-025 Handleiding

25 April 2023

Ozito PFFP-65E Handleiding

8 April 2023

Ozito SWPP-800 Handleiding

2 April 2023

Ozito PSDW-350 Handleiding

28 Maart 2023

Ozito PSA-001 Handleiding

15 Maart 2023

Ozito PXGTPS-0182 Handleiding

25 Februari 2023

Handleiding Pomp

Nieuwste handleidingen voor Pomp

Einhell Royal N-TMP-R400 Handleiding

4 December 2024

Einhell Royal TMP-R 400 Handleiding

4 December 2024

Gardenline GLRP 300 Handleiding

30 November 2024

Astralpool Eco Range Handleiding

30 November 2024

Technaxx TX-261 Handleiding

23 November 2024

Nibe F1255PC Handleiding

20 November 2024

Fluval A402 Handleiding

20 November 2024

Fluval A202 Handleiding

20 November 2024

Fluval A101 Handleiding

20 November 2024

Aerotec TECH ST Handleiding

18 November 2024