NuTone LA225WH Handleiding

NuTone Deurbel LA225WH

Lees hieronder de 📖 handleiding in het Nederlandse voor NuTone LA225WH (8 pagina's) in de categorie Deurbel. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
MODEL LA225WH
Page 1
WESTMINSTER AND TWO-NOTE
WIRELESS CHIME
Installation & Operating Instructions
IMPORTANT: This wireless pushbutton and chime set is for
residential use, only. It will operate at an unobstructed distance
of 100 feet. Building materials may reduce operating distance.
Certain building materials; such as, but not limited to metal,
concrete, brick, stucco and foil-lined insulation; cause greater
interference than others; for example, wood or vinyl siding.
INSTALL PUSHBUTTON BATTERY
Refer to Figures 1 and 2.
1. Remove pushbutton and 3V lithium coin-battery from packaging.
2. Insert small, flat-blade screwdriver into bottom of pushbutton and twist
to separate its base.
3. Orient battery with “+” side viewable.
4. Insert battery into holder and press to seat.
5. Insert top of mounting base onto pushbutton and press bottom
together until mounting base snaps securely onto pushbutton.
Use only 3V (volt) lithium CR2032 style coin-battery for replacement.
INSTALL CHIME BATTERIES
Refer to Figures 3 and 4.
1. Remove chime from packaging.
2. Orient chime face-down.
3. Press on battery compartment cover serrations and slide cover in
direction of triangular-arrow.
4. Remove battery compartment cover and set aside.
5. Insert three (3) 1.5V “AA” alkaline batteries (not supplied) into battery
compartment oriented as shown on back of battery compartment.
6. Slide battery compartment cover back onto chime until it snaps
securely into place.
Figure 1
“PUSH”
TO OPEN COVER
Figure 3
3V LITHIUM
CR2032-STYLE
COIN
BATTERY
Figure 2
SLOT
Figure 4
“SLIDE”
TO OPEN
3 - “AA” SIZE BATTERIES
Figure 5
LEARN BUTTON
“LEARN” PROCEDURE
Refer to Figure 5.
1. Set wireless pushbutton and chime next to each other.
2. Press and release “Learn” button on side of chime.
3. Confirm two (2) lower-tone beeps are heard to indicate entered
“Learn” mode.
4. Press and release wireless pushbutton.
5. Confirm chime-tone is heard.
6. Repeat Step 4 to cycle through available chime-tones.
7. When desired chime-tone is heard, press and release “Learn” button
on side of chime (Note: Chime may not respond to this button being
pressed if it is too soon after chime-tone sounds).
8. Confirm two (2) higher-tone beeps are heard to indicate exited “Learn”
mode.
9. Press and release wireless pushbutton and confirm chime-tone hasn’t
changed.
‱ Multiple wireless pushbuttons can be used with a single chime by
selecting different chime-tones for each wireless pushbutton.
‱ Chime can erase all “Learned” wireless pushbuttons by pressing
and holding “Learn” button on side of chime (two initial lower-tone
beeps will sound). Release “Learn” button on side of chime after
approximately 10 seconds when four (4) higher-tone beeps are heard.
DETERMINE USABLE LOCATIONS
Do not plan to mount pushbutton directly on metal or concrete
surfaces; install a 1/8 to 1/4” wood spacer between pushbutton and
metal or concrete mounting surface.
Some stucco houses have metal mesh in the wall structure, which
will affect the wireless chime performance.
Experiment with various pushbutton and chime locations to
determine location that gives best performance before mounting
permanently.
Chime must not be located within 1-foot of any metal.
Pushbutton and chime should be located within 100-feet of each
other.
1. Place chime near its desired mounting location.
2. Select a level location and hold pushbutton in its desired mounting
location.
3. Press and release pushbutton.
4. Confirm chime-tone sounded.
5. If chime-tone does not sound, temporarily affix pushbutton to
mounting surface with double-stick or folded-over tape; repeat Steps 3
and 4.
6. If chime-tone still does not sound, move location of chime closer to
pushbutton; repeat Steps 3 and 4.
MODEL LA225WH
Page 2
Figure 6
MOUNT PUSHBUTTON
Refer to Figures 1 and 6.
1. After selecting usable locations in previous section, go to pushbutton
location.
2. Insert small, flat-blade screwdriver into bottom of pushbutton and twist
to separate its mounting base.
3. Make sure pushbutton mounting location is level.
4. Position pushbutton mounting base with “TOP” arrow correctly
oriented and mark base mounting holes locations.
5. Drill two (2) holes, 1/16” diameter if using supplied screws alone or
3/16” diameter if using supplied plastic anchors and screws, at base
mounting hole locations.
6. If 3/16” diameter holes were drilled, insert supplied plastic anchors.
7. Secure pushbutton base to mounting location with two (2) supplied
screws.
8. Make sure black O-ring is completely seated in its mounting base
groove with round edge at top and flat edge at bottom.
9. Hook pushbutton top catch onto top of base, swing pushbutton into
position and press bottom of pushbutton until it securely snaps onto
base.
MOUNT CHIME
Refer to Figure 7.
Chime may be used as a
portable device or wall
mounted.
1. After selecting usable locations
in previous section, go to chime
location.
2. Measure 1-7/8” down and
centered from top of chime
location and mark mounting
screw position.
3. Drill a hole, 1/16” diameter if
using supplied screw alone or
3/16” diameter if using supplied
plastic anchor and screw,
at marked mounting screw
location.
4. If 3/16” diameter hole was
drilled, insert supplied plastic
anchor.
5. Tighten screw until 1/8” remains
protruding.
6. Place chime keyhole slot over mounting screw.
7. Level chime.
TROUBLESHOOTING GUIDE
1. Chime does not sound:
a. Check battery polarity.
b. Replace batteries in chime and pushbutton.
c. Bring chime next to wireless pushbutton and test:
1. If chime sounds then change mounting location of chime.
2. If chime does not sound then conduct erase procedure per note
at end of “Learn” Procedure then conduct “Learn” Procedure,
Steps 1 through 9.
2. Chime loses volume or changes tone: Change batteries in chime.
3. Chime sounds when wireless pushbutton is not pressed:
a. Release pushbutton catch at bottom and check inside for signs of
moisture; check O-ring for cracks or damage.
b. Conduct erase procedure per note at end of “Learn” Procedure
then conduct “Learn” Procedure, Steps 1 through 9.
Figure 7
BASE
PLASTIC
ANCHORS
TOP

BLACK
“O” RING
MOUNTING
SCREWS
CHIME
1/8”
KEYHOLE
SLOT
1-7/8”
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
Regulatory Information
The user is cautioned that changes or modifications not
expressly approved by the party responsible for regulatory
compliance could void the user’s authority to operate this
equipment.
MODÈLE LA225WH
Page 3
CARILLON SANS FIL WESTMINSTER
ET DEUX NOTES
Directives d’installation et d’utilisation
IMPORTANT : Cet ensemble de bouton-poussoir et de carillon sans fil
est conçu uniquement pour un usage rĂ©sidentiel. Il fonctionne jusqu’à
une distance sans obstruction de 30 mÚtres (100 pi). Des matériaux
de construction peuvent en réduire la portée. Certains matériaux de
construction comme le mĂ©tal, le bĂ©ton, la brique, le stucco et l’isolant
couvert de papier aluminium causent plus d’interfĂ©rences que
d’autres comme le parement de bois ou de vinyle.
INSTALLATION DE LA PILE
DU BOUTON-POUSSOIR
Voir les figures 1 et 2.
1. Sortez de l’emballage le bouton-poussoir et la pile bouton de 3V au lithium.
2. Insérez un petit tournevis plat au bas du bouton-poussoir et tournez-le
pour en séparer la base.
3. Placez la pile avec le cÎté « + » visible.
4. InsĂ©rez la pile dans son logement et pressez pour l’appuyer.
5. Insérez la base dans le bouton-poussoir et pressez les deux parties
ensemble pour bien les emboĂźter.
N’utilisez qu’une pile bouton de 3V (volts) au lithium CR2032 comme
pile de remplacement.
INSTALLATION DES PILES DU CARILLON
Voir les figures 3 et 4.
1. Sortez le carillon de l’emballage.
2. Placez le carillon face vers le bas.
3. Appuyez sur les cannelures du couvercle du compartiment Ă  piles et
glissez-le dans le sens de la flĂšche triangulaire.
4. Enlevez le couvercle du compartiment et mettez-le de cÎté.
5. Insérez trois (3) piles alcalines « AA » de 1,5 V (non comprises) dans
le compartiment à piles dans le sens indiqué au fond du compartiment.
6. Replacez le couvercle du compartiment à piles en le glissant jusqu’à
ce qu’il s’emboüte en place.
Figure 1
« POUSSER »
POUR OUVRIR
LECOUVERCLE
Figure 3
PILE BOUTON
AU LITHIUM
CR2032 3V
Figure 2
FENTE
Figure 4
« GLISSER »
POUR OUVRIR
3 PILES DE TYPE « AA »
Figure 5
BOUTON APPRENDRE
PROCÉDURE D’« APPRENTISSAGE »
Voir la figure 5.
1. Placez le bouton-poussoir et le carillon l’un Ă  cĂŽtĂ© de l’autre.
2. Appuyez sur le bouton « Apprendre » sur le cÎté du carillon puis
relĂąchez-le.
3. Le carillon Ă©met deux (2) bips de basse tonalitĂ© pour confirmer qu’il
est bien en mode « Apprentissage ».
4. Appuyez sur le bouton-poussoir sans fil puis relĂąchez-le.
5. Confirmez que vous avez bien entendu le carillon.
6. RĂ©pĂ©tez l’étape 4 pour passer entre les tonalitĂ©s du carillon.
7. Lorsque vous entendez le type de carillon souhaité, appuyez sur
le bouton « Apprendre » sur le cÎté du carillon puis relùchez-le.
(Remarque : le carillon risque de ne pas réagir si vous appuyez trop
tÎt sur ce bouton aprÚs que le carillon ait résonné).
8. Le carillon Ă©met deux (2) bips de haute tonalitĂ© pour confirmer qu’il
abien quittĂ© le mode « Apprentissage ».
9. Appuyez sur le bouton-poussoir sans fil et relùchez-le pour vérifier
que la tonalitĂ© du carillon n’a pas changĂ©.
‱ Vous pouvez utiliser plusieurs boutons-poussoirs sans fil avec le
mĂȘme carillon en choisissant des tonalitĂ©s diffĂ©rentes pour chacun.
‱ Le carillon peut effacer tous les boutons-poussoirs « appris » si vous
maintenez appuyé le bouton « Apprendre » sur le cÎté du carillon
(deux bips de basse tonalité se font entendre). Relùchez le bouton
« Apprendre » aprÚs environ 10 secondes lorsque vous entendez
quatre (4) bips de haute tonalité.
CHOIX DES EMPLACEMENTS UTILISABLES
Ne fixez pas le bouton-poussoir directement sur une surface en
métal ou en béton; installez une petite cale en bois de 3 à 6 mm
(1/8 à 1/4 po) entre le bouton et la surface métallique ou en béton.
Certaines maisons Ă  revĂȘtement en stucco ont un treillis mĂ©tallique
dans leur charpente, ce qui nuira au fonctionnement du carillon.
Essayez divers emplacements pour le bouton-poussoir et le
carillon pour déterminer le meilleur endroit possible avant de les
fixer en permanence.
Le carillon ne doit pas ĂȘtre situĂ© Ă  moins de 30 cm (1 pi) de toute
surface métallique.
Le bouton-poussoir et le carillon ne doivent pas ĂȘtre sĂ©parĂ©s de
plus de 30 mùtres (100 pi) l’un de l’autre.
1. Placez le carillon prĂšs de l’endroit oĂč il sera fixĂ©.
2. Choisissez un endroit de niveau et tenez le bouton-poussoir
àl’emplacement voulu.
3. Appuyez sur le bouton-poussoir et relĂąchez-le.
4. Vérifiez que le carillon a bien sonné.
5. Si le carillon ne sonne pas, fixez temporairement le bouton-poussoir Ă 
la surface de montage avec du ruban double face ou un ruban replié;
répétez les étapes 3 et 4.
6. Si le carillon ne sonne toujours pas, rapprochez le carillon du bouton-
poussoir; répétez les étapes 3 et 4.

Product specificaties

Merk: NuTone
Categorie: Deurbel
Model: LA225WH

Heb je hulp nodig?

Als je hulp nodig hebt met NuTone LA225WH stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Deurbel NuTone

NuTone

NuTone LA223WH Handleiding

9 Juni 2024
NuTone

NuTone LA224RWH Handleiding

9 Juni 2024
NuTone

NuTone LA226WH Handleiding

9 Juni 2024
NuTone

NuTone BKL340KWH Handleiding

9 Juni 2024
NuTone

NuTone LA227WH Handleiding

9 Juni 2024
NuTone

NuTone LA225WH Handleiding

9 Juni 2024
NuTone

NuTone BKL342LWH Handleiding

9 Juni 2024
NuTone

NuTone CP2MZAB Handleiding

18 Februari 2024
NuTone

NuTone CP2ILSN Handleiding

18 Februari 2024
NuTone

NuTone CP2TTSN Handleiding

18 Februari 2024

Handleiding Deurbel

Nieuwste handleidingen voor Deurbel

Elektrobock

Elektrobock BZ33-MP3 Handleiding

20 Oktober 2024
Eufy

Eufy Video Doorbell C30 Handleiding

30 September 2024
Cata

Cata THALASSA PRO 90 GGR Handleiding

27 Augustus 2024
Cata

Cata CK 6000 X Handleiding

27 Augustus 2024
Cata

Cata THALASSA 600 GWH Handleiding

27 Augustus 2024
Cata

Cata THALASSA PRO 700 GBK Handleiding

27 Augustus 2024
Cata

Cata THALASSA PRO 800 GBK Handleiding

27 Augustus 2024
Cata

Cata GALA 900 L Handleiding

27 Augustus 2024
Cata

Cata CK 9000 X Handleiding

27 Augustus 2024
Vibell

Vibell OR-VID-MD-1084 Handleiding

22 Augustus 2024