NuTone CP2OHAB Handleiding
Lees hieronder de π handleiding in het Nederlandse voor NuTone CP2OHAB (4 pagina's) in de categorie Deurbel. Deze handleiding was nuttig voor 19 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
D) Doors vary in thickness depending on the manufacturer. At
the edge of the door, measure the thickness of the door. Then,
determine the distance to the center to the edge of the door
(half the thickness of the door). Using the awl (or nail), mark
a point on the edge of the door where the centerline pencil
mark (from Step 1C) and the center of the edge of the door
meet (half the thickness), see .Figure #3
Step 2
Drill the Door
A) Using the 2-1/8β hole saw, drill the cross bore hole centered
on the mark made on the face of the door from Step 1B. See
Figure #3 Important:. To avoid splintering or marring the
door, drill from one side of the door until the pilot bit comes
through the door. Then ξΏnish drilling from the other side of
the door, using the hole made by the pilot bit as your guide
until the cross bore hole is complete.
B) Using the 1β bit, drill the edge bore hole centered on the mark
made on the edge of the door where the centerline and center
thickness met from Step 1D, see Figure #3 Important:.
Make sure that you drill a full 3-1/2β deep, to accommodate
the overall length of the 2-3/8β latch. If you are using a 2-3/4β
backset latch, then the overall depth must be at least 3-3/4β.
ξξξξξv
ξξξξξvξ
ξξξξξvξ
ξξξξξv
&ORξξξξξξvξ"ACKSET
&ORξξξξξξvξ"ACKSET
#ROSSξ"OREξ
(OLEξξξξξξξξvξ
$IAMETER
-ARKξFROMξ
3TEPξξ"
%DGEξ"ORE
(OLEξξξξv
$IAMETER
-ARKξFROMξ
3TEPξξ$
$OORξ4HICKNESS
&ACEPLATE
-ORTISE
!REA
#ENTERLINE
-ARKξFROMξ
3TEPξξ#
-INIMUMξ
ξξξξξ ξTOξCENTERξv
LINEξOFξDOORξ
KNOBξCROSSξ
BOREξHOLE
Door Hardware
Installation Instructions
Rosette Passage and Privacy
Carefully unpackage all components and place them within easy
reach. Find on Page 4 of these instructions for a listing Figure #1
and drawing of each component. Detach and place Figure #1
beside the components for easy reference. Check your door to see
if it has been prepped (pre-drilled) for installing a lock. If your
door has already been prepped for installation, start at Step 4. If
your door has not been prepped for installation, you will need a
#2 Phillips screwdriver, a drill, a 2-1/8β hole saw, a 7/64β drill bit,
a 1β drill bit, chisel, pencil, tape and an awl (or nail).
Step 1
Mark the Door
A) Locate the Door Preparation Template that is included with
the instructions. Fold the template along the βedge-of-doorβ
line. : Before positioning the template, make sure Important
that you are aligning it on the . non-hinged edge of the door
Carefully position the template so that the narrow portion
of the template wraps around the edge of the door, and the
large portion of the template remains on the face of the door,
see . The centerline indicates the center of where Figure #2
the knob or lever will be located. Slide the template up or
down on your door so that the horizontal centerline is located
at a height that is both comfortable to use and attractive in
appearance. Typically this will be approximately 36β-38β
from the ξoor, see Figure #2. Once you have chosen the
height, tape the template to the door.
B) The backset is the distance from the edge of the door to
the center of the rosette. Standard backsets are 2-3/8β and
2-3/4β. Determine the backset of your latch (Part #5), by
checking the marking on the latch itself (if marked, it will say
2-3/8β or 2-3/4β). If the latch is not marked, measure the latch
between points A and B to determine the backset, as shown
in Figure #2. Once you know your backset, ξΏnd the point on
the template where the centerline crosses the vertical line that
corresponds with the correct backset. Using the awl (or nail)
mark this point, making sure that it is marked well enough to
see on the door once the template is removed.
C) Follow the centerline around the edge of the door and using
a pencil, extend the centerline onto the edge of the door. The
mark should be parallel to the ξoor. Once this mark is made,
you may remove the template from the door. Page 1 - PK143
For
Assistance
Call:
1-800-522-7336
8 am - 5 pm, Monday - Friday, MST
(A) (B)
Template
Edge
of
Door
Face of Door
Centerline
Latch
Backset
Measurement
2-3/8β or 2-3/4β
Figure #2
Figure #3
Anti-
Rotation
Block
Latch
Tongue
Star Shaped
Hub
Inside Face of Door
Threaded
Privacy Pin
Hole
C) Determine which direction the door will swing when it is
being opened. Rotate the latch tongue so that the ξat edge of
the tongue faces toward the direction the door swings when
being opened (and the round edge towards the doorjamb).
Once oriented correctly, install the faceplate (Part #7) over the
latch tongue (Part #5a), locking the latch tongue orientation.
Fasten in place using two 1β wood screws (Part #8) Hint:
Coating the screw threads with a small amount of soap (liquid
or bar soap) will make installation easier.
Step 5
Install the Trim
A) Using for reference, gather together the trim half A Figure #1
(Part #1), trim half B (Part #2), 1-1/2β³ rosette machine screws
(Part #3), and Phillips screwdriver.
B) Find trim half A (Part #1). Place trim half A on the outside of
the door, such that the spindle is inserted into the star-shaped
hub of the latch and the screw bosses are nested in the top and
bottom slots in the anti-rotation block, see . Figure #5 Lever
designs only: If installing a lever, see for correct Figure #6
orientation of lever on the door. If your lever is oriented
incorrectly, move it to the other side of the door so it matches
the correct orientation in , before proceeding with Figure #6
installation. Make sure that the Privacy function only:
privacy hole in the rose is oriented so that it is closest to the
edge of the door where the latch tongue sticks out.
Correct Lever Orientation
(Lever Rotates Downward)
Incorrect Lever Orientation
To correct, remove from door and
mount on opposite door face
Door
Edge
Step 3
Mortise for the Faceplate
A) Using Figure #1 for reference, ξΏnd the faceplate (Part
#7). On the edge of the door, center the faceplate over the
newly drilled edge bore hole, so that the D-shaped hole in
the faceplate is centered over the 1β edge bore hole. Align
it so that the edges are parallel to the edges of the door and
roughly centered side-to-side. Mark around the faceplate with
a pencil and remove from door.
B) Using the chisel, score the outline of the faceplate. Next,
chisel away the material within the outline to a depth of 1/8β.
When you are done, you should be able to insert the latch
(part #5), place the faceplate over the latch tongue (Part #5a),
and have the faceplate be ξush with the edge of the door.
C) Again, using the faceplate as a template and the awl as a
marking tool, mark for the two screws holes that will hold the
faceplate on the door. Remove the faceplate from the door to
avoid marring the ξΏnish. Then, drill the two screw holes using
a 7/64β drill bit. Make sure the holes are drilled at least 1β
deep. Having too small or too shallow of a hole can cause the
screws to shear off.
Installing Your Lock
Step 4
Install the Latch
A) Once your door is prepped for installation, you will need a #2
Phillips screwdriver for the installation of your latch.
B) Locate the latch (Part #5) and the anti-rotation block (Part
#4). Insert the anti-rotation block in the cross bore hole so
that the arrow on the block is pointing toward the edge of the
door. Install the latch in the edge bore hole, making sure that
it is correctly inserted through the anti-rotation block. When
installed correctly, the star-shaped hub in the latch should be
centered in the hole of the anti-rotation block, see Figure #4.
Privacy function only: The privacy latch must be inserted
into the door so that the locking mechanism (threaded privacy
pin hole - Part #5b) is facing the inside of the door, see
Figure #1.
Page 2 - PK143
Figure #4
Spindle
Screw
Bosses
Figure #5
Figure #6
C) Hold trim half A on the door. Place trim half B (Part #2) on
the other side of the door, such that the spindle is inserted
into the star-shaped hub of the latch and the screw bosses are
nested in the top and bottom slots in the anti-rotation block.
Now hold both trim halves in place with one hand.
Privacy
function only: Make sure that the privacy hole in the rose is
oriented so that it is closest to the edge of the door where the
latch tongue sticks out.
D) Insert the ξΏrst 1-1/2β rosette machine screw (Part #3) into
the top hole of trim half B and loosely tighten until the screw
can hold both halves of the trim on the door. Important:
Make sure that the screwdriver is held in a way that it will not
scratch the knob/lever or rosette.
E) Insert the second 1-1/2β rosette machine screw into the lower
hole and tighten until snug. Tighten down both screws until
the rosette is securely attached on the door.
F) On the interior side of the door, Privacy function only:
screw in the privacy pin (Part #9) until snug. Do not over-
tighten. With the door open, test the privacy lock by pushing
the pin in and then trying the knob on the opposite side of the
door to see if it is locked. Then turn the knob on the interior
side of the door and this will unlock the door.
Step 6
Prepare the Doorjamb and Install
the Strike
A) Using for reference, gather together the strike (Part Figure #1
#6), two 1β wood screws (Part #8), a drill, 1β drill bit, awl (or
nail), a 7/64β drill bit, a pencil and a chisel.
B) If you are installing a privacy lock, make sure the latch is
not locked. Rotate the knob or lever to retract the latch and
carefully close the door, making sure that the latch is fully
retracted and does not scratch the doorjamb. Slowly release
the knob/lever and let the latch tongue extend against the
doorjamb.
C) Using the pencil, lightly mark the doorjamb at the level of the
top and bottom of the latch tongue (Part #5a). These need to
be light marks, so that they can be erased later if needed. Turn
the knob/lever again to retract the latch and re-open the door.
Now extend the marks so that they are approximately 1/2β
from the edge of the door jamb where the door stops when it
is closed, See Figure #7.
D) Repeat Step 6B, and verify that the latch tongue is falling
between the two marks.
E) Measure the thickness of the door. Take half of the door
thickness and measure that same distance from the edge of
the doorjamb where the door stops when it is closed. Mark
on the doorjamb this distance halfway between the two lines
from Step 6C, see Figure #7.
F) Using the awl, mark where the point that is halfway
between the two lines made in Step 6C crosses the line
marked in Step 6E.
G) Using a 1β drill bit, drill a hole centered on the mark from
Step 6F. Make sure the hole is at least 5/8β deep. Clean out
any sawdust from the hole.
H) Using the strike (Part #6) as a template, center the strike
over the 1β hole, mark a line around it in pencil and remove
from doorjamb.
I) Using the chisel, score the outline of the strike. Next, chisel
away the material within the outline to a depth of 1/16β.
When you are done, you should be able to place the strike
in the mortised out area and it should be ξush with the
doorjamb.
J) Again, using the strike as a template and the awl as a
marking tool, mark the two screws holes that will hold the
strike on the door. Remove the strike from the doorjamb
to avoid marring the ξΏnish. Then, drill the two screw holes
using a 7/64β drill bit. Make sure the holes are drilled at
least 1β deep. Having too small or too shallow a hole can
cause the screws to shear off.
K) Fasten the strike in place using two 1β wood screws (Part
#8). Hint: Coating the screw threads with a small amount
of soap (liquid or bar soap) will make installation easier.
Page 3 - PK143
Congratulations! You are now
on your way to enriching your
life with !
Mark from
Step 6F
Chiseled
Area for
Strike
Half of
Door
Thickness
Door Jamb
Stop
Door Jamb
Lines from
Step 6C
Figure #7
Product specificaties
Merk: | NuTone |
Categorie: | Deurbel |
Model: | CP2OHAB |
Heb je hulp nodig?
Als je hulp nodig hebt met NuTone CP2OHAB stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Deurbel NuTone
9 Juni 2024
9 Juni 2024
9 Juni 2024
9 Juni 2024
9 Juni 2024
9 Juni 2024
9 Juni 2024
18 Februari 2024
18 Februari 2024
18 Februari 2024
Handleiding Deurbel
- Deurbel Philips
- Deurbel Panasonic
- Deurbel Fysic
- Deurbel Grundig
- Deurbel Honeywell
- Deurbel Inventum
- Deurbel Quigg
- Deurbel Acti
- Deurbel Alecto
- Deurbel Arendo
- Deurbel Axis
- Deurbel Balay
- Deurbel Baseline
- Deurbel Beafon
- Deurbel Belkin
- Deurbel Bellman
- Deurbel Bitron Video
- Deurbel Byron
- Deurbel Delta
- Deurbel Denver
- Deurbel Desa
- Deurbel DIO
- Deurbel Doorsafe
- Deurbel Doro
- Deurbel Ebench
- Deurbel Eken
- Deurbel Elektrobock
- Deurbel Elro
- Deurbel Envivo
- Deurbel EQ-3
- Deurbel Eufy
- Deurbel Ezviz
- Deurbel Fagor
- Deurbel Foscam
- Deurbel Friedland
- Deurbel Geemarc
- Deurbel GeoVision
- Deurbel Gira
- Deurbel GlobalTronics
- Deurbel Grothe
- Deurbel Hama
- Deurbel Hauck
- Deurbel Heidemann
- Deurbel Hikvision
- Deurbel HQ
- Deurbel Intersteel
- Deurbel KlikaanKlikuit
- Deurbel Kogan
- Deurbel Konig
- Deurbel Kruidvat
- Deurbel Lifetec
- Deurbel Lorex
- Deurbel LSC SmartConnect (Action)
- Deurbel Marquant
- Deurbel ME
- Deurbel Melinera
- Deurbel Mercury
- Deurbel Merlin
- Deurbel Mr Safe
- Deurbel Nedis
- Deurbel Nest
- Deurbel Netatmo
- Deurbel Perel
- Deurbel Plieger
- Deurbel Profile
- Deurbel Renkforce
- Deurbel Ring
- Deurbel SecuFirst
- Deurbel Sencor
- Deurbel Silvercrest
- Deurbel Sinji
- Deurbel SkyBell
- Deurbel Smart
- Deurbel Smartwares
- Deurbel Somfy
- Deurbel Swissvoice
- Deurbel Toa
- Deurbel Tronic
- Deurbel Trust
- Deurbel Ubiquiti
- Deurbel Unitec
- Deurbel Urmet
- Deurbel V-Tac
- Deurbel Velleman
- Deurbel Zmodo
- Deurbel Jacob Jensen
- Deurbel Olympia
- Deurbel Orbegozo
- Deurbel Caliber
- Deurbel Exibel
- Deurbel Steren
- Deurbel DoorBird
- Deurbel Aspes
- Deurbel EMOS
- Deurbel Infiniton
- Deurbel Arlo
- Deurbel Avidsen
- Deurbel Imou
- Deurbel Techly
- Deurbel Extel
- Deurbel M-e
- Deurbel REV
- Deurbel Oricom
- Deurbel Cata
- Deurbel Chacon
- Deurbel ACE
- Deurbel Nexa
- Deurbel Swann
- Deurbel Milectric
- Deurbel Apelson
- Deurbel Hombli
- Deurbel Reolink
- Deurbel Fanvil
- Deurbel EQ3
- Deurbel X-Sense
- Deurbel ORNO
- Deurbel Brilliant
- Deurbel Bell4U
- Deurbel Vimar
- Deurbel Legrand
- Deurbel Intertechno
- Deurbel EKO
- Deurbel Pentatech
- Deurbel ZAMEL
- Deurbel AVANTEK
- Deurbel Vibell
- Deurbel ALC
- Deurbel Middle Atlantic
- Deurbel Bearware
Nieuwste handleidingen voor Deurbel
11 December 2024
7 December 2024
3 December 2024
3 December 2024
2 December 2024
2 December 2024
2 December 2024
2 December 2024
2 December 2024
2 December 2024