Nitecore P12 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Nitecore P12 (2 pagina's) in de categorie Zaklamp. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
®
奈特科尔—全能照明专家
P12
使用说明书
产品特性
·采用CREE XM-L2 (U2级) LED
·最高1000流明超强亮度输出
·采用晶亮电镀技术结合PDOT字精确优化技术制造的最优化光学系统
·最大光强13,500坎德拉
·最远射程232
·长达520小时的最长续航时间
·为战术应用设计的侧按调档按钮一键控制7种亮度和功方便快捷
·侧按调档按钮内藏电量指示灯可以提示电池剩余电量
·电量指示灯可显示电池电压精确到0.1V)
·智慧型档位记忆功SOS和信标功能除外)
·高效率恒流电亮度恒定
·配备不锈钢镀钛抱
·双面镀膜防刮光学镜片
·航太级铝合金制造
·耐磨的军规三级硬化表面处理
·符合IPX8防水标准(水下2米)
·1米防摔能
·尾部倒立功能
体积
长度 139mm
头部直径 25.4mm
尾部直径 25.4mm
重量 88克不含电池)
战术点亮
轻按尾部开关,电筒会开手电筒熄灭
长时间开启/关闭手电筒
开启手电筒:下尾部按钮开直到“嗒的一声后松手手电筒开
关闭手电筒:次按下尾部按钮开直到“嗒的一声后松手手电筒关
亮度调节
在电筒开启状态下,按一次调档按电筒亮度将按“超低亮-低亮-中亮-高亮”
环改变亮度。
注:筒会在开启高亮档3分钟后自动降低亮度输出以防止过并有效地保障电池
的使用寿命。
使用特殊档位暴闪/SOS功能/信标
在电筒开启状态下,按调档按钮超过一电筒将会开启暴闪,如果需要选择更多
的特殊档只需要长按调档按钮超过一秒即可在SOS功能-信标-暴闪顺序切换
如果需要退出特殊档位并恢复当前亮需按一下调档按钮。
注:P12具有自动记忆功再次激活电筒将自动进入已选亮度或档位(SOS和信标
功能除外
电量提示
1. 当手电筒开启,并且电池电量剩余将近一半位于调档按钮的蓝色电量指示灯将
每2闪烁1次提示用户
当手电筒开启,并且电池电量将近耗尽时,位于调档按钮的蓝色电量指示灯将连
续快速闪烁提示用户。
2. 在手电筒关闭的状态下按着调档按钮并保持不放同时按下尾部按钮开关蓝色
电量指示灯将以闪烁来表示出电池电(精确到±0.1V电池电压为4.2V
指示灯将闪烁4停顿一秒后再闪烁2次来表示4.2V显示电池电压完成
电筒随即进入当前记忆的亮度和功能
更换电池
当电池电量不位于调档按钮的蓝色电量指示灯将连续快速闪烁,电筒甚至会出
亮度变暗或者无法调光的情况。此时应对电筒进行更换电池。
保养电筒
请每半年使用软布清洁电筒的螺牙并使用硅润滑油润滑螺牙。
注意事项
请根据适用的当地法律和法规处置设备/电池。
保固
NITECORE®产品拥有售后保固服务。在购买本产品的15天内如果有任何质量问题
均可向经销商要求免费更换在购买本产品的60个月内享受免费保固服务在超
60个月免费保固期后本产品享有终身有限度保固服务如需要更换重要部件则需
收取成本费用
本保固规则不适用于以下情况:
1. 人为破改装本产品。
2. 错误操作导致产品损坏(如装反电池等)。
3. 电池漏液导致产品损坏
如对奈特科尔产品有任何疑问欢迎联系当地的代理商或发邮件到
4008869828@nitecore.cn
※本说明书的所有图片陈述及文字信息仅供参考,请以官网www.nitecore.cn实际
信息为准广州希脉创新科技有限公司拥有对说明书内容的最终解释权和修改权。
400客户线400-886-9828 买我
广州希技有
询热线+86-20-83862000
售邮info@nitecore.com
址:www.nitecore.cn
址:广省广市天高普1021号56355
编:510653
亮度&时间
注:
以上数据按照国际手电筒测量标 所述之测量方使用电池为:ANSI/NEMA FL1
1节 18650锂电3.7V 2600mAh)量所不同电池或使用环境可能会对以上数
产生影响
配件
优质电筒抱夹,战术胶环备用
备用防水O圈
选用电池
1小时
15分钟
1000 1000 1000 1000流明 流明 流明 流明
13500
坎德拉
232
2000
坎德拉
90
300
坎德拉
34
10
坎德拉
6
IPX8, 2水下 米(防水等级)
1米(防跌落高度)
高亮
240流明
中亮
70流明
低亮
1流明
超低亮 暴闪 SOS 信标
28小时6 520小时 小时 ─ ─
─ ─
─ ─
尺寸规格 标称电压 是否可用
一次性锂金属电池 CR123 3V (推荐使用)
18650锂充电电池 18650 3.7V (推荐使用)
可充电锂离子电池 RCR123 3.7V (可以使用)
使用电筒
入/电池
如图所示,拧开电池盖后入/
卸电池并拧紧电池盖。
警告
1. 请将电池按照正极朝灯头方向放
反装电池电筒将不能工作。
2. 不能将光线直接照射眼以免
对眼睛造成伤害。
更多信息请关注新浪微博
NITECORE奈特科
P30111222
HIGH MID LOW
LUMENS
240
LUMENS
1000
LUMENS
1000
LUMENS
1000
LUMENS
1000
LUMENS
70
LUMEN
1
1
h15min
28
h
6
h
LOWER STROBE SOS
LOCATION BEACON
520
h─ ─ ─
─ ─ ─
─ ─ ─
232m
13500cd
90m
2000cd
34m
300cd
6m
10cd
IPX8, 2m
(Waterproof AND Submersible)
1m (Impact Resistant)
®User Manual
Features
Premium CREE XM-L2 (U2) LED
Maximum output of 1000 lumens
Second generation ‘Crystal Coating Technologycombined with ‘Precision
Digital Optics Technology’ provide extreme reflector performance
Boasts a peak beam intensity of 13,500cd and a throw distance of up to
232 meters
High efficiency circuit board provides up to 520 hours runtime on low
Side switch interface provides one-handed operation and easy access to all
functions
Side switch features an indicator light which displays remaining battery
power
Power indicator’s secondary function displays battery voltage (accurate to
0.1V)
Intelligent memory function stores preferred brightness setting
High-efficiency regulation circuit provides unwavering output
Toughened ultra-clear mineral glass with anti-reflective coating
Constructed from aero grade aluminium alloy with HAIII military grade
hard-anodized finish
Waterproof in accordance with IPX8 (two meters submersible)
Impact resistant to 1 meter
Stainless steel titanium-plated clip included
Tail stand capability
Dimensions
Length: 139mm (5.47”)
Head Diameter: 25.4mm (1”)
Tail Diameter: 25.4mm (1”)
Weight: 88grams (3.10oz)(without battery)
Thanks for purchasing NITECORE!
Brightness & Runtime
The All-Round Flashlight Expert
Accessories
Quality holster, clip, tactical
ring, lanyard, spare tail cap,
spare O-ring
Battery Options
As illustrated, after unscrewing the
battery cap, insert / remove the
battery(s) and screw to tighten the tail
cap.
WARNING
1. Ensure batteries are inserted with the
positive (+) end pointing to the head.
The P12 will not operate with
incorrectly inserted batteries.
2. Ensure when turning the P12 on, the
beam is directed away from the eyes
of people or animals.
Switching ON/OFF
To switch ON: Press the button on the tailcap until aclick” is heard.
To switch OFF: Press the button on the tailcap a second time until a “click
is heard.
General Operations
With the light turned on, press the side switch in quick succession to cycle
through the following brightness levels: ultra-low, low, medium and high.
Once a desired setting is displayed, it may be saved by turning the light off at
the tail switch.
Note: For user safety and to prevent overheating / failure, the P12 will
automatically switch to a lower mode after three minutes of use at its highest
level of output.
Special Modes
With the light turned on, press and hold the side switch to activate Strobe
mode. Press and hold once again to access Location Beacon mode and repeat
once more for SOS mode. To exit any one of these modes simply press the
side switch to be returned to your previously used brightness level.
NB: Strobe mode is the default special mode and is the only special mode
that has a memory function. If the light is turned off at the tail switch while
in strobe mode, strobe will resume when the light is next turned on. SOS and
Location Beacon modes have no memory function.
Power Tips
1. With the light switched on, the power indicator will blink once every two
seconds when power levels reach 50%.
2. With the light switched on, the power indicator will blink rapidly when
power levels are low.
3. With the light turned off, press and hold the side switch while
simultaneously pressing the tail switch to display the battery voltage
(accurate to ±0.1V) with a series of blinks. For example, when the battery
voltage is at a maximum charge of 4.2V, the power indicator will blink 4
times in quick succession, followed by a one second pause and two more
blinks, indicating a total battery voltage of 4.2V.
Changing Batteries
When the power indicator blinks rapidly this indicates the batteries need to be
replaced. Alternatively if the light becomes dim or unresponsive to adjustment
this also indicates batteries need to be replaced.
Maintenance
Every 6 months, threads should be wiped with a clean cloth followed by a thin
coating of silicon-based lubricant.
Warnings
Dispose of the device/batteries in accordance with applicable local laws
and regulations.
Warranty Service
All NITECORE® products are warranted for quality. Any defective /
malfunctioning NITECORE® product can be repaired free of charge for a
period of 60 months (5 years) from the date of purchase. Beyond 60 months
(5 years), a limited warranty applies, covering the cost of labor and
maintenance, but not the cost of accessories or replacement parts.
The warranty is nullified in all of the following situations:
1. The product(s) is/are broken down, reconstructed and/or modified by
unauthorized parties.
2. The product(s) is/are damaged through improper use.
3. The product(s) is/are damaged by leakage of batteries.
For the latest information on NITECORE® products and services, please
contact a local NITECORE® distributor or send an email to
service@nitecore.com
※All images, text and statements specified herein this user manual are for
reference purpose only. Should any discrepancy occurs between this manual
and information specified on www.nitecore.com, information on our official
website shall prevail. SYSMAX Innovations Co., Ltd. reserves the rights to
interpret and amend the content of this document at any time without prior
notice.
NOTICE
The above data has been measured in accordance with the international flashlight
testing standards ANSI/NEMA FL1 using one x 3.7V 2600mAh 18650 battery under
laboratory conditions. The data may vary slightly during real-world use due to
battery type, individual usage habits and environmental factors.
SIZE
Nominal voltage
Compatible
Primary Lithium battery CR123 3V Y (Recommended)
18650 Rechargeable Li-ion battery 18650 3.7V Y (Recommended)
Rechargeable Li-ion battery RCR123 3.7V Y
P12
SYSMAX Innovations Co., Ltd.
TEL: +86-20-83862000
FAX: +86-20-83882723
E-mail: info@nitecore.com
Web: www.nitecore.com
Address Rm 2601-06, Central Tower, No.5 Xiancun Road, Tianhe
District, Guangzhou, 510623, Guangdong, China
Please find us on facebook:
Nitecore Flashlight
P30111222
Made in China
Operation instructions
Battery Installation / Removal
Momentary illumination
Momentary illumination mode is accessed by half pressing and holding the tail
switch with flashlight turned off. Simply release the switch to turn the light
off again.


Product specificaties

Merk: Nitecore
Categorie: Zaklamp
Model: P12
Kleur van het product: Zwart
Gewicht: 88 g
Breedte: 139 mm
Materiaal behuizing: Aluminium
Aantal lampen: 1 lampen
Soort lamp: LED
Internationale veiligheidscode (IP): IPX8
Waterdicht: Ja
Schokbestendig: Ja
Ondersteund aantal accu's/batterijen: 1
Levensduur accu/batterij: 520 uur
Lichtstroom: 1000 lm
Lichtintensiteit: 13500 cd
Type batterij: 18650
Type zaklamp: Zaklamp
Lichtbundelafstand (max): 232 m
Schokbestendig tot: 1 m
Diameter hoofd: 25.4 mm

Heb je hulp nodig?

Als je hulp nodig hebt met Nitecore P12 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Zaklamp Nitecore

Handleiding Zaklamp

Nieuwste handleidingen voor Zaklamp