Monoprice Joule 3D Printer DIY Assembly Kit Handleiding

Monoprice 3D Printer Joule 3D Printer DIY Assembly Kit

Lees hieronder de 📖 handleiding in het Nederlandse voor Monoprice Joule 3D Printer DIY Assembly Kit (45 pagina's) in de categorie 3D Printer. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/45

Joule 3D Print

Joule 3D PrintJoule 3D Printer DIY Assembly Kit

er DIY Assembly Kit

er DIY Assembly Kit er DIY Assembly Kit

P/N 43363

User's Manual

User's Manual User's Manual

SAFETY WARNINGS

SAFETY WARNINGSSAFETY WARNINGS AND GUIDELINES

AND GUIDELINES

AND GUIDELINES AND GUIDELINES

Please read this entire manual before using this device, paying extra attention to these safety warnings and guidelines. Please keep this

manual in a safe place for future reference.

• This device is intended for indoor use only.

• Do not expose this device to water or moisture of any kind. Do not place drinks or other containers with moisture on or near the

device. If moisture does get in or on the device, immediately remove it from its power source and allow it to fully dry before

reapplying power.

• Do not touch the device, the power cord, or any other connected cables with wet hands.

• Do not install this device on an unstable surface where it could fall and cause either personal injury or damage to the device

and/or other equipment.

• Do not expose this device to excessive vibration, extreme force, shock, or fluctuations in temperature or humidity.

• Do not expose this device to excessively high temperatures. Do not place it in, on, or near a heat source, such as a fireplace,

stove, radiator, etc. Do not leave it in direct sunlight.

• Do not place or install this device in an area where it can be exposed to excessive amounts of dust, humidity, oil, smoke, or

combustible vapors.

• Use only in a well-ventilated area. Do not use in close, confined spaces.

• Prior to operation, check the unit and power cord for physical damage. Do not use if physical damage has occurred.

• Before plugging the unit into a power outlet, ensure that the outlet provides the same type and level of power required by the

device.

• This device uses a grounded power cord and requires a ground connection for safe operation. Ensure that the power source has

a proper ground connection. Do not modify the plug or use a "cheater" plug to bypass the ground connection.

• Unplug this device from the power source when not in use.

• Take care to prevent damage to the power cord. Do not allow it to become crimped, pinched, walked on, or become tangled

with other cords. Ensure that the power cord does not present a tripping hazard.

• Never unplug the unit by pulling on the power cord. Always grasp the connector head or adapter body.

• Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or detergents. For stubborn deposits, moisten the cloth

with warm water.

• This device has no user serviceable parts. Do not attempt to open, service, or modify this device.

• Take care to avoid touching hot parts, including heat blocks, extruder nozzle, extruded filament, and the heated build plate.

• Do not wear gloves when operating or repairing to avoid entanglement.

• Keep the printer and all accessories out of reach of children.

• Do not reach inside the printer during operation.

• Always allow the printer and extruded filament to cool before reaching inside.

• Ensure that the printer is turned off and unplugged from its power source before making repairs or performing service.

Product specificaties

Merk:	Monoprice
Categorie:	3D Printer
Model:	Joule 3D Printer DIY Assembly Kit
Soort bediening:	Draaiknop
Kleur van het product:	Zwart
Ingebouwd display:	Ja
Materiaal behuizing:	Metaal
Beeldschermdiagonaal:	4.3 "
Geïntegreerde geheugenkaartlezer:	Ja
Compatibele geheugenkaarten:	MicroSD (TransFlash)
Kijkglas:	Ja
Vermogensverbruik (max):	350 W
Display technologie:	LCD
Ondersteunt Windows:	Windows 10, Windows 7 Ultimate x64
Ondersteunt Mac-besturingssysteem:	Ja
Printtechnologie:	Fused Filament Fabrication (FFF)
AC-ingangsspanning:	115/230 V
AC-ingangsfrequentie:	50 - 60 Hz
Breedte mondstuk:	0.4 mm
Printmateriaal:	ABS, Polylactic acid (PLA)
Maximale printsnelheid:	180 mm³/s
Ondersteunde filamentdikte:	1.75 mm
Maximaal afdrukformaat:	220 x 220 x 250 mm
Laagdikte (min):	0.1 mm
Laagdikte (max):	0.4 mm
Aantal printkoppen:	1
Ondersteunde laagdikte:	0.1, 0.4 mm
Maximale printplatformtemperatuur:	100 °C
Ondersteunde modelbestandsindelingen:	obj, stl
Verwarmd printplatform:	Ja
Positioneringsnauwkeurigheid (X, Y):	0.2 mm