Milwaukee M18 Fuel Super Hawg 2709-22 Handleiding

Milwaukee Boormachine M18 Fuel Super Hawg 2709-22

Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee M18 Fuel Super Hawg 2709-22 (49 pagina's) in de categorie Boormachine. Deze handleiding was nuttig voor 13 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/49

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

Cat. No.

No de cat.

2709-20

2711-20

M18™ FUEL™ SUPER HAWG™ RIGHT ANGLE DRILLS

PERCEUSE SUPER HAWG™ M18™ FUEL™ DE ÉLECTRICIEN

TALADRO SUPER HAWG™ DE M18™ FUEL™ PARA ELECTRICISTAS

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S

MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN

COMPRENDRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL

MANUAL DEL OPERADOR.

BATTERY TOOL USE AND CARE

PERSONAL SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WORK AREA SAFETY

ELECTRICAL SAFETY

POWER TOOL USE AND CARE

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive atmos-

pheres, such as in the presence of ﬂ ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while op-

erating a power tool. Distractions can cause you

to lose control.

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁ ed plugs and matching outlets will

reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase the

risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

• If operating a power tool in a damp location is

unavoidable, use a ground fault circuit inter-

rupter (GFCI) protected supply. Use of an GFCI

reduces the risk of electric shock.

• Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the inﬂ

uence of drugs, alcohol or medication.

moment of inattention while operating power tools

may result in serious personal injury.

• Use personal protective equipment. Always

wear eye protection. Protective equipment such

as a dust mask, non-skid safety shoes, hard hat or

hearing protection used for appropriate conditions

will reduce personal injuries.

• Prevent unintentional starting. Ensure the

switch is in the o-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your ﬁ nger on the switch or energizing power tools

that have the switch on invites accidents.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Keep proper footing and bal-

ance at all times. This enables better control of the

power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewelry. Keep your hair and clothing away from

moving parts. Loose clothes, jewelry or long hair

can be caught in moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

• Do not let familiarity gained from frequent use of

tools allow you to become complacent and ig-

nore tool safety principles. A careless action can

cause severe injury within a fraction of a second.

• Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

• Do not use the power tool if the switch does not

turn it on and o. Any power tool that cannot be

controlled with the switch is dangerous and must

be repaired.

• Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools.

Such preventive safety measures reduce the risk

of starting the power tool accidentally.

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

• Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition that

may aect the power tool’s operation. If dam-

aged, have the power tool repaired before use.

Many accidents are caused by poorly maintained

power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power tool

for operations dierent from those intended could

result in a hazardous situation.

• Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles

and grasping surfaces do not allow for safe handling

and control of the tool in unexpected situations.

• Recharge only with the charger speciﬁ ed by the

manufacturer. A charger that is suitable for one

WARNING Read all safety warnings, instructions, illustrations and speciﬁ cations provided

with this power tool. Failure to follow all instructions listed below may result in electric shock, ﬁ re

and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in

the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

FUNCTIONAL DESCRIPTION

• Use auxiliary handle(s), if supplied with the

tool. Loss of control can cause personal injury.

• Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring. Cutting

accessory contacting a “live” wire may make

exposed metal parts of the power tool “live” and

could give the operator an electric shock.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

• WARNING Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to cause

cancer, birth defects or other reproductive harm.

SPECIFIC SAFETY RULES

SYMBOLOGY

Volts

Direct Current

No Load Revolutions

per Minute (RPM)

C US Underwriters Laboratories, Inc.

United States and Canada

1. Top handle

2. Keyed chuck 1/2"

(Cat. No. 2709-20)

3. Shift knob

4. Side handle

5. LED

6. Chuck key storage

7. Main handle

8. Trigger

9. Control switch

10. 7/16" QUIK-LOK™ Hex chuck (Cat. No. 2711-20)

9 7

SERVICE

type of battery pack may create a risk of ﬁ re when

used with another battery pack.

• Use power tools only with speciﬁ cally desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and ﬁ re.

• When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal

to another. Shorting the battery terminals together

may cause burns or a ﬁ re.

• Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact ac-

cidentally occurs, ﬂ ush with water. If liquid con-

tacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or burns.

• Do not use a battery pack or tool that is dam-

aged or modiﬁ ed. Damaged or modiﬁ ed batteries

may exhibit unpredictable behavior resulting in ﬁ re,

explosion or risk of injury.

• Do not expose a battery pack or tool to ﬁ re

or excessive temperature. Exposure to ﬁ re or

temperature above 265°F (130°C) may cause

explosion.

• Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range speciﬁ ed in the instructions.

Charging improperly or at temperatures outside

the speciﬁ ed range may damage the battery and

increase the risk of ﬁ re.

• Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

• Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and

other masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are spe-

cially designed to ﬁ lter out microscopic particles.

SPECIFICATIONS

Volts

Cat. No.

2709-20/2711-20

Selfeed

Bit

2-9/16"

4-5/8"

Auger

Bit

1-1/2"

Twist

Bit

5/16"

1/2"

Ship Auger

Bit

1-1/2"

Hole

Saw

Steel Wood

Capacity

ASSEMBLY

WARNING Recharge only with the

charger speciﬁ ed for the battery. For speciﬁ c

charging instructions, read the operator’s

manual supplied with your charger and battery.

Inserting/Removing the Battery

To remove the battery, push in the release buttons

and pull the battery pack away from the tool.

To insert the battery, slide the pack into the body of

the tool. Make sure it latches securely into place.

Bit Selection

• Use sharp bits. Sharp bits are less likely to bind

when drilling.

• Use the proper bit for the job. There are many

types of bits designed for speciﬁ c purposes. Check

the information on the bit's packaging for proper

usage.

• Do not use bits larger than the rated capacity of

the drill. Gear damage or motor overload may

result (see "Speciﬁ cations").

Installing Bits

Always remove the battery before inserting or

removing bits. Select the proper style and size bit

for the application.

WARNING Always remove battery

pack before changing or removing acces-

sories. Only use accessories specifically

recommended for this tool. Others may be

hazardous.

Installing Bits into Keyed Chucks

(Cat. No 2709-20)

1. Remove the battery pack.

2. Open the chuck jaws wide

enough to insert the bit. Be

sure the bit shank and chuck

jaws are clean. Dirt particles

may prevent the bit from lin-

ing up properly.

3. Insert the bit into the chuck. Center the bit in the

chuck jaws and lift it about off of the bottom. 1/16"

Tighten the chuck jaws by hand to align the bit.

4. Place the chuck key in each of the three holes

in the chuck, turning it clockwise to tighten the

chuck securely.

NOTE: Never use a wrench or means other than

a chuck key to tighten or loosen the chuck.

5. To remove the bit, insert the chuck key into

one of the holes in the chuck and turn it coun-

terclockwise.

Installing Bits into QUIK-LOK™ Hex 7/16"

Chuck (Cat. No 2711-20)

1. Remove the battery pack.

2. To attach an accessory, press the shank into the

hex drive chuck.

3. To remove the accessory, pull out the ring and

remove the accessory. Release the ring.

Side Handle

The side handle can be installed on either side of

the tool. To install the side handle, thread it into the

socket on the desired side of the tool and tighten

it securely.

OPERATION

WARNING Always remove battery

pack before changing or removing acces-

sories. Only use accessories specifically

recommended for this tool. Others may be

hazardous.

Bit binding

If the bit binds, the drill will suddenly react in the

opposite direction of the rotation of the bit. Reduce

the chances of a sudden reaction by following the

instructions listed below. Prepare for a sudden

reaction by holding or bracing securely.

To reduce the chance of bit binding:

• Use sharp bits. Sharp bits are less likely to bind

when drilling.

• Use the proper bit for the job. There are many

types of bits designed for speciﬁ c purposes.

• Keep selfeed bits aligned with the work surface

so bits go in straight (see "Drilling").

• Avoid drilling warped, wet, knotty, and/or pitchy

material if possible.

• Avoid drilling in material that you suspect contains

hidden nails or other things that may cause the bit

to bind.

The direction of reaction is always opposite of the

direction of bit rotation. Reaction is even more likely

to occur when enlarging already existing holes and

at the point when the bit breaks through the other

side of the material.

If the bit does bind:

1. Release the trigger immediately.

2. Reverse the motor.

3. Remove the bit from the work and start again.

4. Do not pull the trigger on and o to attempt to

start a stalled bit. This will damage the drill.

WARNING To reduce the risk of injury,

wear safety goggles or glasses with side

shields.

WARNING To reduce the risk of per-

sonal injury when drilling, hold the tool by isu-

lated gripping surfaces when performing an

operation where the cutting tool may contact

hidden wiring. Contact with a "live" wire will

make exposed metal parts of the tool "live"

and shock the operator

WARNING To reduce the risk of injury,

hold or brace securely. Always be prepared

for bit binding and drill reaction.

Bracing for forward rotation

When drilling in forward, the bit will rotate in a

clockwise direction. If the bit binds in the hole, the

bit will come to a sudden stop and drill will suddenly

react in a counterclockwise direction.

The following ﬁ gures show examples of properly

bracing the tool for forward rotation.

A. Forward (clockwise) rotation

B. Reaction

C. Brace drill with motor housing here

D. Brace drill with side handle here

If the bit binds, the motor housing braced against

the stud will hold the drill in position.

No Load RPM

High 0 - 950

Low 0 - 350

Product specificaties

Merk:	Milwaukee
Categorie:	Boormachine
Model:	M18 Fuel Super Hawg 2709-22

Heb je hulp nodig?

Als je hulp nodig hebt met Milwaukee M18 Fuel Super Hawg 2709-22 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Boormachine Milwaukee

Milwaukee M12 BDDXKIT Handleiding

16 November 2024

Milwaukee M18 FHACOD32 Handleiding

29 Mei 2024

Milwaukee M18 ONEFHP Handleiding

29 Mei 2024

Milwaukee M18 ONEFH Handleiding

29 Mei 2024

Milwaukee M18 CHM Handleiding

29 Mei 2024

Milwaukee M18 FHM Handleiding

29 Mei 2024

Milwaukee M18 ONEDD3 Handleiding

16 April 2024

Milwaukee SB 2-35 D Handleiding

10 April 2024

Milwaukee M18 BLH Handleiding

10 April 2024

Milwaukee M18 BLHX Handleiding

10 April 2024

Handleiding Boormachine

Nieuwste handleidingen voor Boormachine

Makita DDF459 Handleiding

21 December 2024

Total TRHLI1601 Handleiding

16 December 2024

Black Decker 1963 Handleiding

8 December 2024

Black Decker 1350-09 Handleiding

8 December 2024

Gude GTB 16/5 R Handleiding

8 December 2024

Hikoki DV36DA Handleiding

7 December 2024

Hikoki DH26PC2 Handleiding

7 December 2024

Hikoki DH28PCY2 Handleiding

7 December 2024

Zipper ZI-BHA1500DN Handleiding

7 December 2024

Bavaria BRH 850 Handleiding

5 December 2024