Milwaukee M18 Fuel One-Key 2916-22 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee M18 Fuel One-Key 2916-22 (11 pagina's) in de categorie Hamer. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/11
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
M18 FUELâ„¢ 1-1/4" SDS PLUS D-HANDLE ROTARY HAMMER
W/ ONE-KEYâ„¢
PERCEUSE À PERCUSSION ROTATIVE À POIGNÉE EN « D »
DE 32 mm (1-1/4") M18 FUELâ„¢ SDS PLUS AVEC ONE-KEYâ„¢
ROTOMARTILLO CON EMPUÑADURA EN "D" " DE 32 (1-1/4mm )
M18 FUELâ„¢ SDS PLUS CON ONE-KEYâ„¢
Cat. No. / No de cat.
2916-20
SDS
PLUS
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instruc-
tions, illustrations and speciîš¿ca-
tions provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, îš¿re and/or serious injury. Save all
warnings and instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodiîš¿ed plugs and matching outlets will
reduce risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of an GFCI reduces
the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch
is in the o󰀨-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your îš¿nger on
the switch or energizing power tools that have the
switch on invites accidents.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
• Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts. Loose clothes, jewelry or long hair
can be caught in moving parts.
• If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power
tool for your application. The correct power tool
will do the job better and safer at the rate for which
it was designed.
• Do not use the power tool if the switch does not
turn it on and o󰀨. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
• Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
• Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may a󰀨ect the power tool’s operation. If damaged,
have the power tool repaired before use. Many
accidents are caused by poorly maintained power
tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations di󰀨erent from those intended could
result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
BATTERY TOOL USE AND CARE
• Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of îš¿re when used
with another battery pack.
• Use power tools only with specically designated
battery packs. Use of any other battery packs may
create a risk of injury and îš¿re.
• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins
4
Setting the Depth Gauge
1. Press in the clamping lever.
2. Slide the depth gauge rod backward or forward
until it is set for the desired depth.
NOTE: The drilling depth is the distance between
the tip of the bit and the tip of the depth gauge rod.
Drilling Depth
3. Release the clamping lever.
WARNING
Always remove battery pack before
changing or removing accesso-
ries. Only use accessories speciîš¿cally recom-
mended for this tool. Others may be hazardous.
Installing Drill Bits and Chisels
NOTE: Only use accessories with SDS or SDS Plus
shanks.
Be sure that the shank of the bit is clean. Dirt particles
may cause the bit to line up improperly. Do not use
bits larger than the maximum recommended capacity
of the drill because gear damage or motor overload-
ing may result. For best performance, be sure that
the bit is properly sharpened and the shank is lightly
greased before use.
1. Insert the bit or chisel into the nose of the tool.
2. Rotate bit slowly until it aligns with the locking
mechanism.
3. Push bit into tool until it locks.
4. Check that the bit is locked properly; it should
be possible to pull the bit back and forth slightly
(about 1/4").
5. To remove bits and chisels, pull bit holder release
collar toward the rear of tool and remove bit.
WARNING! Do not touch the drill bits or chisels
with bare hands immediately after drilling; they
may be hot and could burn skin.
ONE-KEYâ„¢
To learn more about the ONE-KEYâ„¢ functionality
for this tool, go to milwaukeetool.com/One-Key. To
download the ONE-KEYâ„¢ app, visit the App Store or
Google Play from your smart device.
ONE-KEYâ„¢ Indicator
Solid Blue Wireless mode is active and ready
to be conîš¿gured via the ONE-KEYâ„¢
app.
Blinking Blue Tool is actively communicating with
the ONE-KEYâ„¢ app.
Blinking Red Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEYâ„¢ app.
OPERATIONFUNCTIONAL DESCRIPTION
1. Side handle
2. Clamping lever
3. Depth gauge rod
4. SDS Plus bit holder
5. Release collar
6. Mode selector
7. Trigger
8. Forward/reverse
swtich
9. Handle
10. AUTOSTOPâ„¢
indicator LED
11. ONE-KEYâ„¢
indicator LED
12. Dust extractor
connection
1
2
3
45
6
7
8
9
12 11
10
ASSEMBLY
WARNING
Recharge only with the charger
speciîš¿ed for the battery. For spe-
cic charging instructions, read the operator’s
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
Always lock the trigger or remove
the battery pack any time the tool
is not in use.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
Only use accessories speciîš¿cally
recommended for this tool. Others
may be hazardous.
To reduce the risk of injury, always use a side
handle when using this tool. Always brace or
hold securely.
Adjusting the Side Handle Position
1. Loosen the side handle by unscrewing the side
handle grip until the side handle rotates freely.
2. Rotate the side handle to the desired position.
3. Tighten the side handle grip securely.
For use with the Dust Extractor
The MILWAUKEE Cat. No. 2916-DE Dust Extrac-
tor plugs directly into the 1-1/4" SDS PLUS Rotary
Hammer. For Dust Extractor assembly and operation,
refer to your Dust Extractor manual.
Product specificaties
| Merk: | Milwaukee |
| Categorie: | Hamer |
| Model: | M18 Fuel One-Key 2916-22 |
Heb je hulp nodig?
Als je hulp nodig hebt met Milwaukee M18 Fuel One-Key 2916-22 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Hamer Milwaukee
21 Februari 2024
4 Juli 2023
19 Mei 2023
18 Mei 2023
5 Mei 2023
26 April 2023
22 April 2023
18 April 2023
28 Maart 2023
20 Maart 2023
Handleiding Hamer
- Hamer Bosch
- Hamer AEG
- Hamer DeWalt
- Hamer Bavaria
- Hamer Einhell
- Hamer Ferm
- Hamer Global
- Hamer Goon
- Hamer Gude
- Hamer Hikoki
- Hamer Hitachi
- Hamer Makita
- Hamer Metabo
- Hamer Parkside
- Hamer Powerfix
- Hamer Powerplus
- Hamer Robust
- Hamer Ryobi
- Hamer Scheppach
- Hamer Skil
- Hamer Stanley
- Hamer Taurus
- Hamer Topcraft
- Hamer Trotec
- Hamer Wiha
- Hamer Ozito
- Hamer Black And Decker
- Hamer Ronix
- Hamer Cocraft
- Hamer Hilti
- Hamer Power Craft
- Hamer Fieldmann
- Hamer Porter-Cable
- Hamer CMI
- Hamer Craftsman
- Hamer Alpha Tools
- Hamer Full Boar
- Hamer King Craft
- Hamer Toolson
- Hamer Anova
- Hamer Einhell Bavaria
- Hamer McKenzie
- Hamer Prowork
- Hamer Proviel
- Hamer XU1
- Hamer Ergotools Pattfield
- Hamer MyTool
- Hamer Bavaria By Einhell
- Hamer Workzone Titanium
Nieuwste handleidingen voor Hamer
5 December 2024
5 December 2024
18 November 2024
5 September 2024
29 Augustus 2024
15 Juli 2024
15 Juli 2024
15 Juli 2024
11 Juli 2024
11 Juli 2024