Milwaukee 48-22-9519 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee 48-22-9519 (1 pagina's) in de categorie Hamer. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/1
54-49-9419
SERVICE PARTS LIST
BULLETIN NO.
MILWAUKEE TOOL l www.milwaukeetool.com
13135 W. LISBON RD., BROOKFIELD, WI 53005
Drwg. 1
EXAMPLE:
Component Parts (Small #) Are Included
When Ordering The Assembly (Large #).
0
00
48-22-9419 Milled Face Hickory Hammer
48-22-9519 Smooth Face Hickory Hammer
HICKORY HAMMERS July 2018
REVISED BULLETIN
WIRING INSTRUCTION
DATE
CAT. NO.
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 -------------- Steel Wedge (2)
2 -------------- Wood Wedge (1)
3 -------------- Hammer Head
(Milled: 48-22-9419, Smooth: 48-22-9519)
(1)
4 -------------- Hickory Hammer Handle (1)
5 14-46-9419 Handle Replacement Kit (1)
1
2
3
4
5 1 2
4
1. Before beginning, line up the wooden wedge with the slot in the top of
the replacement handle. With a pencil, make a mark on the thick side
of the wooden wedge where the top of the handle ends. This will allow
you to see when the wooden wedge is fully inserted down into the
handle slot. It is important not to exceed the slot depth with the wedge,
as this can cause damage to the new handle.
2. Aftercuttingtheoldhandleo󰀨belowthehead,turntheheadoverand
punch the remaining handle material out from the top of the 'eye' of
the hammer head. Insert slotted end of the new replacement handle
into the bottom of the hammer head. Firmly tap the bottom of handle
with a mallet or other hammer to tightly set the handle into eye of the
head, but not so far as to 'peel' or cut into the wood of the handle at
the bottom of the eye. Rely on the mechanical bond of the wood and
steel wedges to make the head-to-handle connection strong.
3. Next place the thin tip of the wooden wedge into the slotted end of the
handle that is protruding out of the top of the hammer head. It is norm-
al for the wooden wedge to be wider than the slot and eye opening.
Firmly tap the wooden wedge all the way to the pencil mark on wedge,
so that the wedge is fully inserted in the handle slot. There should be
approximately 1/2" of the wedge protruding past the end of the handle.
 DONOTcontinuedrivingthewedgeinanyfurther.
MILWAUKEE Hickory Replacement Instructions
USE CAUTION and Wear safety glasses when performing the following procedure.
4. Afterdrivingthewoodenwedgein,trimo󰀨excesswedgeandhandle
material as close to the top of the head as possible. USE CAUTION
 whencuttingo󰀨excessmaterial.Positionthetwosteelwedgeson 
trimmed end of handle and wood wedge to get an idea of spacing.
Position the larger steel wedge to the wider front of the eye, and the
 smallersteelwedgetothebackoftheeye.Whenyouhavewedges
 evenlyspacedintheeye,notincontactwiththesideoftheeye,rmly
 tapthewedgesin,oneatatimecompletelyushwiththetrimmed 
surface.
5. To keep the cut end of the handle from losing moisture and shrinking
inside the hammer head, put a few drops of mineral or 'butcherblock'
oil on the end grain to help retain the moisture content. This will pro-
 longtheservicelifeofthehandle.
Model 48-22-9419
Shown with milled face
Pencil
mark
Bottom
of slot
1
Product specificaties
| Merk: | Milwaukee |
| Categorie: | Hamer |
| Model: | 48-22-9519 |
Heb je hulp nodig?
Als je hulp nodig hebt met Milwaukee 48-22-9519 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Hamer Milwaukee
21 Februari 2024
4 Juli 2023
19 Mei 2023
18 Mei 2023
5 Mei 2023
26 April 2023
22 April 2023
18 April 2023
28 Maart 2023
20 Maart 2023
Handleiding Hamer
- Hamer Bosch
- Hamer AEG
- Hamer DeWalt
- Hamer Bavaria
- Hamer Einhell
- Hamer Ferm
- Hamer Global
- Hamer Goon
- Hamer Gude
- Hamer Hikoki
- Hamer Hitachi
- Hamer Makita
- Hamer Metabo
- Hamer Parkside
- Hamer Powerfix
- Hamer Powerplus
- Hamer Robust
- Hamer Ryobi
- Hamer Scheppach
- Hamer Skil
- Hamer Stanley
- Hamer Taurus
- Hamer Topcraft
- Hamer Trotec
- Hamer Wiha
- Hamer Ozito
- Hamer Black And Decker
- Hamer Ronix
- Hamer Cocraft
- Hamer Hilti
- Hamer Power Craft
- Hamer Fieldmann
- Hamer Porter-Cable
- Hamer CMI
- Hamer Craftsman
- Hamer Alpha Tools
- Hamer Full Boar
- Hamer King Craft
- Hamer Toolson
- Hamer Anova
- Hamer Einhell Bavaria
- Hamer McKenzie
- Hamer Prowork
- Hamer Proviel
- Hamer XU1
- Hamer Ergotools Pattfield
- Hamer MyTool
- Hamer Bavaria By Einhell
- Hamer Workzone Titanium
Nieuwste handleidingen voor Hamer
18 November 2024
5 September 2024
29 Augustus 2024
15 Juli 2024
15 Juli 2024
15 Juli 2024
11 Juli 2024
11 Juli 2024
11 Juli 2024
10 Juli 2024