Milwaukee M18 Fuel 2603-22 Handleiding

Milwaukee Boormachine M18 Fuel 2603-22

Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee M18 Fuel 2603-22 (11 pagina's) in de categorie Boormachine. Deze handleiding was nuttig voor 63 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/11

M18™ CORDLESS 1/2" DRILL/DRIVER AND HAMMER DRILL/DRIVER

PERCEUSE-VISSEUSE ET PERCEUSE À PERCUSSION DE

M18™ 13 mm (1/2")

TALADRO DESTORNILLADOR Y TALADRO DE PERCUSIÓN

DE 13 mm (1/2") M18™

Cat. No.

No de cat.

2603-20

2604-20

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S

MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN

COMPRENDRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL

MANUAL DEL OPERADOR.

1. Trigger

2. Control switch

3. LED

4. Keyless chuck

5. Torque selector collar

6. Application selector collar

7. Speed selector

FUNCTIONAL DESCRIPTION

SYMBOLOGY

Volts

Direct Current

No Load Revolutions per

Minute (RPM)

C US Underwriters Laboratories, Inc.

United States and Canada

SPECIFICATIONS

Cat. No.

Volts

DC No Load RPM BPM

2603-20 18 Low 0 - 550

High 0 - 1 850

2604-20 18 Low 0 - 550

High 0 - 1 850

Low 0 - 9350

High 0 - 31 450

Steel

Wood

MasonryFlat Bit Auger Bit Hole Saw Screws (dia.)

2603-20 1/2"

1/2"

1-1/2"

3/8"

2604-20 1/2"

1/2"

1-1/2"

3/8"

5/8"

CAPACITIES

PERSONAL SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WORK AREA SAFETY

ELECTRICAL SAFETY

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive atmos-

pheres, such as in the presence of ﬂ ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁ ed plugs and matching outlets will

reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase

the risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use

of a cord suitable for outdoor use reduces the risk

of electric shock.

• If operating a power tool in a damp location is

unavoidable, use a ground fault circuit inter-

rupter (GFCI) protected supply. Use of an GFCI

reduces the risk of electric shock.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

WARNING

READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS.

Failure

to follow the warnings and instructions may result in electric shock, ﬁ re and/or serious

injury. Save all warnings and instructions for future reference. The term "power

tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

• Do not use the power tool if the switch does not

turn it on and o. Any power tool that cannot be

controlled with the switch is dangerous and must

be repaired.

• Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such pre-

ventive safety measures reduce the risk of starting

the power tool accidentally.

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

• Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power tool

for operations dierent from those intended could

result in a hazardous situation.

• Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inﬂ uence of drugs, alcohol or medi-

cation. A moment of inattention while operating

power tools may result in serious personal injury.

• Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

• Prevent unintentional starting. Ensure the

switch is in the o-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your ﬁ nger on the switch or energising power tools

that have the switch on invites accidents.

SERVICE

• Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

SPECIFIC SAFETY RULES

BATTERY TOOL USE AND CARE

• Recharge only with the charger speciﬁ ed by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of ﬁ re

when used with another battery pack.

• Use power tools only with speciﬁ cally desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and ﬁ re.

• When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery terminals

together may cause burns or a ﬁ re.

• Under abusive conditions, liquid may be eject-

ed from the battery; avoid contact. If contact

accidentally occurs, ﬂ ush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation

or burns.

• Wear ear protectors when impact drilling.

Exposure to noise can cause hearing loss.

• Use auxiliary handle(s), if supplied with the

tool. Loss of control can cause personal injury.

• Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its

own cord. Cutting accessory contacting a “live”

wire may make exposed metal parts of the power

tool “live” and could give the operator an electric

shock.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

• WARNING Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and

other masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are spe-

cially designed to ﬁ lter out microscopic particles.

OPERATION

WARNING Always remove battery

pack before changing or removing acces-

sories. Only use accessories specifically

recommended for this tool. Others may be

hazardous.

WARNING To reduce the risk of injury,

wear safety goggles or glasses with side

shields.

WARNING To reduce the risk of injury,

always hold securely.

Selecting Drill or Drive Action

(Cat. No. 2603-20)

1. To use the drilling mode, rotate

the torque selector collar until the

drill symbol appears in line

with the arrow.

2. rotate To use the driving mode

the torque selector collar until the

desired clutch setting appears in

line with the arrow.

The adjustable clutch, when prop-

erly adjusted, will slip at a preset

torque to prevent driving the screw

too deep into different materials

and to prevent damage to the

screw or tool.

Selecting Hammer, Drill or Drive Action

(Cat. No. 2604-20)

1. To use the hammer-drilling

mode, rotate the application

selector collar until the hammer

symbol appears in line with

the arrow. Apply pressure to the bit

to engage the hammering mecha-

nism.

NOTE: The number selected on the torque

selector collar has no eect on operation of the

drill in hammer mode.

NOTE: When using carbide bits, do not use wa-

ter to settle dust. Do not attempt to drill through

steel reinforcing rods. This will damage the

carbide bits.

2. To use the drilling only mode,

rotate the application selector collar

until the drill symbol

appears

in line with the arrow.

NOTE: The number selected on the

torque selector collar has no eect

on operation of the drill in drilling

mode.

Clutch

Setting in. lbs Applications

1-5

6-10

11-15

16-20

21-24

5-25

28-39

42-68

73-84

86-95

Small screws in softwood.

Medium screws in softwood or small

screws in hardwood.

Large screws in softwoods. Medium

screws in hardwood or large screws in

hardwood with pilot hole.

NOTE: Because the settings shown in the table are only

a guide, use a piece of scrap material to test the dierent

clutch settings before driving screws into the workpiece.

Selecting Speed

The speed selector is on top of the motor housing.

Allow the tool to come to a complete stop before

changing speeds. See “Applications” for recom-

mended speeds under various conditions.

1. For Low speed, push the speed selector to

display “1”.

2. For High speed, push the speed selector to

display “2”.

Using the Control Switch

The control switch may be set to three positions:

forward, reverse and lock. Due to a lockout mecha-

nism, the control switch can only be adjusted when

the ON/OFF switch is not pressed. Always allow

the motor to come to a complete stop before using

the control switch.

For (clockwise) forward

rotation, push in the control

switch from the right side of

the tool. Check the direction

of rotation before use.

For (counterclock-reverse

wise) rotation, push in the

control switch from the left

side of the tool. Check direc-

tion of rotation before use.

lock the trigger,

push the

control switch to the center

position. The trigger will not work while the control

switch is in the center locked position. Always

lock the trigger or remove the battery pack before

performing maintenance, changing accessories,

storing the tool and any time the tool is not in use.

Installing Bits

Always remove the battery before inserting or

removing bits. Select the proper style and size bit

for the job.

This tool is equipped with a spindle lock. The chuck

can be tightened with one hand, creating higher grip

strengths on the bit.

1. To open the chuck jaws, turn the sleeve in the

counterclockwise direction.

When using drill bits, allow the bit to strike the

bottom of the chuck. Center the bit in the chuck

jaws and lift it about 1/16” o of the bottom.

When using screwdriver bits, insert the bit far

enough for the chuck jaws to grip the hex of the

bit.

2. To close the chuck jaws, turn the sleeve in the

clockwise direction. The bit is secure when the

chuck makes a ratcheting sound and the sleeve

can not be rotated any further.

3. To remove the bit, turn the sleeve in the coun-

terclockwise direction.

NOTE: A ratcheting sound may be heard when the

chuck is opened or closed. This noise is part of the

locking feature, and does not indicate a problem

with the chuck’s operation.

3. To use the driving screws mode

rotate the application selector col-

lar until the drive symbol ap-

pears in line with the arrow. Then

rotate the torque selector collar

until the desired clutch setting ap-

pears in line with the arrow.

The adjustable clutch, when properly adjusted,

will slip at a preset torque to prevent driving the

screw too deep into dierent materials and to

prevent damage to the screw or tool.

The torque speciﬁ cations shown here are approximate

values obtained with a fully charged battery pack.

Lock

Push to

CENTER

Reverse

Forward

ASSEMBLY

WARNING Recharge only with the

charger speciﬁ ed for the battery. For speciﬁ c

charging instructions, read the operator’s

manual supplied with your charger and battery.

Inserting/Removing the Battery

To remove the battery, push in the release buttons

and pull the battery pack away from the tool.

To insert the battery, slide the pack into the body of

the tool. Make sure it latches securely into place.

Installing the Side Handle

1. To install the side handle,

loosen the side handle grip until

the hooks are far enough apart

to ﬁ t into the slots on the gear

case ring. Position the side

handle on the top, pointing to

the left or right. Tighten the side

handle grip until it is secure.

2. To remove the side handle,

loosen the side handle grip

until the side handle can be

removed. Reposition and tighten securely.

WARNING To reduce the risk of injury,

always use a side handle when using this tool.

Always brace or hold securely. Ensure side

handle is tightened securely before each use.

Hooks

Slots

Starting, Stopping and Controlling Speed

1. To start the tool, grasp the handles ﬁ rmly and

pull the trigger.

NOTE: An LED is turned on when the trigger is

pulled.

2. To vary the speed, increase or decrease the

pressure on the trigger. The further the trigger

is pulled, the greater the speed.

3. To stop the tool, release the trigger. Make sure

the bit comes to a complete stop before laying

the tool down.

Drilling

Place the bit on the work surface and apply ﬁ rm

pressure before starting. Too much pressure will

slow the bit and reduce drilling efﬁ ciency. Too little

pressure will cause the bit to slide over the work

area and dull the point of the bit.

If the tool begins to stall, reduce pressure slightly

to allow the bit to regain speed. If the bit binds,

reverse the motor to free the bit from the workpiece.

Product specificaties

Merk:	Milwaukee
Categorie:	Boormachine
Model:	M18 Fuel 2603-22

Heb je hulp nodig?

Als je hulp nodig hebt met Milwaukee M18 Fuel 2603-22 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Boormachine Milwaukee

Milwaukee M12 BDDXKIT Handleiding

16 November 2024

Milwaukee M18 FHACOD32 Handleiding

29 Mei 2024

Milwaukee M18 ONEFHP Handleiding

29 Mei 2024

Milwaukee M18 ONEFH Handleiding

29 Mei 2024

Milwaukee M18 CHM Handleiding

29 Mei 2024

Milwaukee M18 FHM Handleiding

29 Mei 2024

Milwaukee M18 ONEDD3 Handleiding

16 April 2024

Milwaukee SB 2-35 D Handleiding

10 April 2024

Milwaukee M18 BLH Handleiding

10 April 2024

Milwaukee M18 BLHX Handleiding

10 April 2024

Handleiding Boormachine

Nieuwste handleidingen voor Boormachine

Makita DDF459 Handleiding

21 December 2024

Total TRHLI1601 Handleiding

16 December 2024

Black Decker 1963 Handleiding

8 December 2024

Black Decker 1350-09 Handleiding

8 December 2024

Gude GTB 16/5 R Handleiding

8 December 2024

Hikoki DV36DA Handleiding

7 December 2024

Hikoki DH26PC2 Handleiding

7 December 2024

Hikoki DH28PCY2 Handleiding

7 December 2024

Zipper ZI-BHA1500DN Handleiding

7 December 2024

Bavaria BRH 850 Handleiding

5 December 2024