Milwaukee M18 2615-21 Handleiding
Milwaukee
Boormachine
M18 2615-21
Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee M18 2615-21 (16 pagina's) in de categorie Boormachine. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/16
Cat. No. / No de cat.
2615-20
M18™ CORDLESS 3/8'' RIGHT ANGLE DRILL
POIGNÉE COUDEE ANGLE DROIT DE 10 mm (3/8") M18™
TALADROS EN ANGULOS RECTOS, DE 10 mm (3/8") DE M18™
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instruc-
tions, illustrations and specica-
tions provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, re and/or serious injury. Save all
warnings and instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of an GFCI reduces
the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your nger on
the switch or energizing power tools that have the
switch on invites accidents.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
• Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts. Loose clothes, jewelry or long hair
can be caught in moving parts.
• If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power
tool for your application. The correct power tool
will do the job better and safer at the rate for which
it was designed.
• Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
• Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
• Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many
accidents are caused by poorly maintained power
tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
BATTERY TOOL USE AND CARE
• Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of re when used
with another battery pack.
• Use power tools only with specically designated
battery packs. Use of any other battery packs may
create a risk of injury and re.
3
• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal
to another. Shorting the battery terminals together
may cause burns or a re.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact ac-
cidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
• Do not use a battery pack or tool that is dam-
aged or modied. Damaged or modied batteries
may exhibit unpredictable behavior resulting in re,
explosion or risk of injury.
• Do not expose a battery pack or tool to re or
excessive temperature. Exposure to re or tem-
perature above 265°F (130°C) may cause explosion.
• Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specied in the instructions. Charging
improperly or at temperatures outside the specied
range may damage the battery and increase the risk
of re.
SERVICE
• Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
• Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SPECIFIC SAFETY RULES FOR
RIGHT ANGLE DRILL
•Hold the power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory or fasteners may contact
hidden wiring. Cutting accessory or fasteners
contacting a “live” wire may make exposed metal
parts of the power tool “live” and could give the
operator an electric shock.
Safety instructions when using long drill bits
•Never operate at higher speed than the maximum
speed rating of the drill bit. At higher speeds, the
bit is likely to bend if allowed to rotate freely without
contacting the workpiece, resulting in personal injury.
• Always start drilling at low speed and with the
bit tip in contact with the workpiece. At higher
speeds, the bit is likely to bend if allowed to rotate
freely without contacting the workpiece, resulting in
personal injury.
• Apply pressure only in direct line with the bit
and do not apply excessive pressure. Bits can
bend causing breakage or loss of control, resulting
in personal injury.
•
WARNING
To reduce the risk of injury in ap-
plications that produce a consid-
erable amount of dust, use an OSHA compliant
dust extraction solution in accordance with the
solution’s operating instructions.
• Always use common sense and be cautious when
using tools. It is not possible to anticipate every
situation that could result in a dangerous outcome.
Do not use this tool if you do not understand these
operating instructions or you feel the work is beyond
your capability; contact Milwaukee Tool or a trained
professional for additional information or training.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
•
WARNING
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
lter out microscopic particles.
SYMBOLOGY
Volts
Direct Current
No Load Revolutions per Minute (RPM)
C US
UL Listing for Canada and U.S.
SPECIFICATIONS
Cat. No. 2615-20 .....................................................
Volts 18 DC..............................................................
Battery Type .................................................M18™
Charger Type M18™................................................
No Load RPM ............................................ 0 - 1500
Capacities
Drilling in Wood (twist bit) .............................. 3/8"
Drilling in Wood (spade bit) .............................. 1"
Driving Screws................................ 1/4" diameter
Recommended Ambient
Operating Temperature ......................0°F to 125°F
FUNCTIONAL DESCRIPTION
1. Keyless Chuck
2. Worklight/Torque LEDs
3. Paddle Switch
4. Control Switch
34
1
2
6
5
5. Handle
6. Clutch Adjusting Dial
ASSEMBLY
WARNING
Recharge only with the charger
specied for the battery. For spe-
cic charging instructions, read the operator’s
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Product specificaties
| Merk: | Milwaukee |
| Categorie: | Boormachine |
| Model: | M18 2615-21 |
Heb je hulp nodig?
Als je hulp nodig hebt met Milwaukee M18 2615-21 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Boormachine Milwaukee
29 Mei 2024
29 Mei 2024
29 Mei 2024
29 Mei 2024
29 Mei 2024
16 April 2024
10 April 2024
10 April 2024
10 April 2024
10 April 2024
Handleiding Boormachine
- Boormachine Bosch
- Boormachine IKEA
- Boormachine Panasonic
- Boormachine AEG
- Boormachine DeWalt
- Boormachine Baier
- Boormachine Basetech
- Boormachine Batavia
- Boormachine Bavaria
- Boormachine Berner
- Boormachine Black Decker
- Boormachine Blucave
- Boormachine Bort
- Boormachine Bruder Mannesmann
- Boormachine Defort
- Boormachine Delta
- Boormachine Dremel
- Boormachine Duro
- Boormachine Duro Pro
- Boormachine Ecomac
- Boormachine Economy
- Boormachine Einhell
- Boormachine Elu
- Boormachine Fe Powertools
- Boormachine Fein
- Boormachine Felisatti
- Boormachine Ferm
- Boormachine Ferrex
- Boormachine Festool
- Boormachine Flex
- Boormachine Gamma
- Boormachine Global
- Boormachine Goon
- Boormachine Gude
- Boormachine Hikoki
- Boormachine Hitachi
- Boormachine Holzmann
- Boormachine Huvema
- Boormachine Hyundai
- Boormachine Kawasaki
- Boormachine Kinzo
- Boormachine Kress
- Boormachine Laserliner
- Boormachine Lux Tools
- Boormachine Luxor
- Boormachine Maestro
- Boormachine Makita
- Boormachine Maktec
- Boormachine Max
- Boormachine Metabo
- Boormachine Parkside
- Boormachine Powerfix
- Boormachine Powerplus
- Boormachine Profitech
- Boormachine Protool
- Boormachine Robust
- Boormachine Rupes
- Boormachine Ryobi
- Boormachine Scheppach
- Boormachine Silverline
- Boormachine Skil
- Boormachine Sparky
- Boormachine Spit
- Boormachine Stanley
- Boormachine Stihl
- Boormachine Stomer
- Boormachine Tanaka
- Boormachine Texas
- Boormachine Toolcraft
- Boormachine Toolland
- Boormachine Topcraft
- Boormachine Trotec
- Boormachine Varo
- Boormachine Velleman
- Boormachine Vonroc
- Boormachine Westfalia
- Boormachine Workzone
- Boormachine Worx
- Boormachine Wurth
- Boormachine Zipper
- Boormachine Ozito
- Boormachine Clas Ohlson
- Boormachine Black And Decker
- Boormachine Steren
- Boormachine Cocraft
- Boormachine Meec Tools
- Boormachine Genesis
- Boormachine Carat
- Boormachine Eibenstock
- Boormachine Hilti
- Boormachine Cotech
- Boormachine Power Craft
- Boormachine Tacklife
- Boormachine Truper
- Boormachine Fieldmann
- Boormachine Mafell
- Boormachine Proxxon
- Boormachine Biltema
- Boormachine Malmbergs
- Boormachine Porter-Cable
- Boormachine Sun Joe
- Boormachine Dedra
- Boormachine Graphite
- Boormachine Narex
- Boormachine RIDGID
- Boormachine Tryton
- Boormachine Herkules
- Boormachine MSW
- Boormachine Sthor
- Boormachine Craftsman
- Boormachine Rikon
- Boormachine Verto
- Boormachine Alpha Tools
- Boormachine Hazet
- Boormachine G-Technology
- Boormachine Yato
- Boormachine Stalco
- Boormachine Baumr-AG
- Boormachine Powerblade
- Boormachine Meister Craft
- Boormachine Max Bahr
- Boormachine Wolfcraft
- Boormachine Kreg
- Boormachine Rok
- Boormachine RUKO
- Boormachine Einhell Bavaria
- Boormachine McKenzie
- Boormachine Ribimex
- Boormachine Ergotools Pattfield
- Boormachine MyTool
- Boormachine Rodcraft
- Boormachine Bavaria By Einhell
- Boormachine Handwerk
Nieuwste handleidingen voor Boormachine
2 November 2024
20 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024