Milwaukee 5426-21 Handleiding

Milwaukee Boormachine 5426-21

Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee 5426-21 (15 pagina's) in de categorie Boormachine. Deze handleiding was nuttig voor 12 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/15

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S

MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN

COMPRENDRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL

MANUAL DEL OPERADOR.

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

HEAVY-DUTY ROTARY HAMMERS AND DEMOLITION HAMMERS

EXTRA ROBUSTES MARTEAUX ROTATIFS ET MARTEAU DE

DÉMOLISSEUR

ROTOMARTILLOS Y MARTILLOS PERFORADORES DE DEMOLICIÓN

HEAVY-DUTY

Cat. No.

No de Cat.

5426-21

5446-21

PERSONAL SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WORK AREA SAFETY

ELECTRICAL SAFETY

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive atmo-

spheres, such as in the presence of ﬂ ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁ ed plugs and matching outlets will

reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase

the risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use

of a cord suitable for outdoor use reduces the risk

of electric shock.

• If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS.

Failure to follow the warnings and instructions may result in electric shock, ﬁ re and/or

serious injury. Save all warnings and instructions for future reference

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

• Do not use the power tool if the switch does not

turn it on and oﬀ. Any power tool that cannot be

controlled with the switch is dangerous and must

be repaired.

• Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

• Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits

etc., in accordance with these instructions,

taking into account the working conditions and

the work to be performed. Use of the power tool

for operations diﬀerent from those intended could

result in a hazardous situation.

• Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the inﬂ uence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personal injury.

• Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

• Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your ﬁ nger on the switch or energising power tools

that have the switch on invites accidents.

SERVICE

• Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

SPECIFIC SAFETY RULES

• Wear ear protectors. Exposure to noise can

cause hearing loss.

• Use auxiliary handle(s), if supplied with the

tool. Loss of control can cause personal injury.

• Hold power tools by insulated gripping surfaces,

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Cutting accessory contacting a live wire may make

exposed metal parts of the power tool live and could

give the operator an electric shock.

• Keep hands away from all cutting edges and

moving parts.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

• WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are spe-

cially designed to ﬁ lter out microscopic particles.

FUNCTIONAL DESCRIPTION

SPECIFICATIONS

Cat. No.

Volts

AC A

No Load

RPM

No Load

BPM

Shank

Type

Carbide Tipped

Percussion Bit

(concrete)

Percussion

Core Bit

(concrete/brick)

5426-21

5446-21

120

120 14

14 350 / 450

- - 2200 / 2840

2200 / 2840 SDS-Max

SDS-Max 1-3/4"

- - 4-1/2" / 6"

- -

SYMBOLOGY

Volts Alternating Current

Amps

No Load Revolutions per Minute

(RPM)

BPM Blows per Minute (BPM)

Mexican Approvals Marking

Underwriters Laboratories, Inc.

United States and Canada

1. Bit holder

2 Rear side handle

position

3. Mode selector

4. Trigger lock-on

(5446-21 only)

5. Trigger

6. Hammer speed control

7. Power indicator

8. Service indicator

9. Side handle

10.Side handle ball (5446-21 only)

11.Clamp

12.Depth gauge rod

Fig. B Fig. C

Fig. A

GROUNDING

WARNING Improperly connecting the

grounding wire can result in the risk of

electric shock. Check with a qualiﬁ ed electri-

cian if you are in doubt as to whether the

outlet is properly grounded. Do not modify

the plug provided with the tool. Never remove

the grounding prong from the plug. Do not

use the tool if the cord or plug is damaged. If

damaged, have it repaired by a MILWAUKEE

service facility before use. If the plug will not

ﬁ t the outlet, have a proper outlet installed by

a qualiﬁ ed electrician.

Grounded Tools: Tools with Three Prong Plugs

Tools marked “Grounding Required” have a three

wire cord and three prong grounding plug. The

plug must be connected to a properly grounded

outlet (See Figure A). If the tool should electrically

malfunction or break down, grounding provides a

low resistance path to carry electricity away from

the user, reducing the risk of electric shock.

The grounding prong in the plug is connected

through the green wire inside the cord to the

grounding system in the tool. The green wire in the

cord must be the only wire connected to the tool's

grounding system and must never be attached to

an electrically “live” terminal.

Your tool must be plugged into an ap-

propriate outlet, properly installed and

grounded in accordance with all codes

and ordinances. The plug and outlet

should look like those in Figure A.

Double Insulated Tools: Tools with Two Prong

Plugs

Tools marked “Double Insulated” do not require

grounding. They have a special double insula-

tion system which satisﬁ es OSHA requirements

and complies with the applicable standards of

Underwriters Laboratories, Inc., the

Canadian Standard Association and

the National Electrical Code. Double

Insulated tools may be used in either

of the 120 volt outlets shown in

Figures B and C.

Grounded tools require a three wire extension

cord. Double insulated tools can use either a two

or three wire extension cord. As the distance from

the supply outlet increases, you must use a heavier

gauge extension cord. Using extension cords with

inadequately sized wire causes a serious drop in

voltage, resulting in loss of power and possible tool

damage. Refer to the table shown to determine the

required minimum wire size.

The smaller the gauge number of the wire, the

greater the capacity of the cord. For example, a 14

gauge cord can carry a higher current than a 16

gauge cord. When using more than one extension

cord to make up the total length, be sure each cord

contains at least the minimum wire size required. If

you are using one extension cord for more than one

tool, add the nameplate amperes and use the sum

to determine the required minimum wire size.

Guidelines for Using Extension Cords

• If you are using an extension cord outdoors,

be sure it is marked with the sufﬁ x “W-A” (“W”

in Canada) to indicate that it is acceptable for

outdoor use.

• Be sure your extension cord is properly wired

and in good electrical condition. Always replace

a damaged extension cord or have it repaired by

a qualiﬁ ed person before using it.

• Protect your extension cords from sharp objects,

excessive heat and damp or wet areas.

READ AND SAVE ALL

INSTRUCTIONS FOR FUTURE USE.

Recommended Minimum Wire Gauge

for Extension Cords*

Extension Cord Length

* Based on limiting the line voltage drop to ﬁ ve volts

at 150% of the rated amperes.

Nameplate

Amperes

0 - 2.0

2.1 - 3.4

3.5 - 5.0

5.1 - 7.0

7.1 - 12.0

12.1 - 16.0

16.1 - 20.0

25'

75'

100'

150'

50'

EXTENSION CORDS

WARNING To reduce the risk of injury,

always use a side handle when using

this tool. Always brace or hold securely.

ASSEMBLY

WARNING To reduce the risk of injury,

always unplug tool before attaching

or removing accessories or making adjust-

ments. Use only speciﬁ cally recommended

accessories. Others may be hazardous.

OPERATION

WARNING To reduce the risk of injury,

always unplug tool before attaching

or removing accessories or making adjust-

ments. Use only speciﬁ cally recommended

accessories. Others may be hazardous.

WARNING To reduce the risk of injury,

keep hands and cord away from the bit

and all moving parts.

WARNING To reduce the risk of injury,

wear safety goggles or glasses with side

shields.

Adjusting the Side Handle Position

1. Loosen the side handle by unscrewing the side

handle grip (5426-21) or ball (5446-21) until the

side handle rotates freely.

2. Rotate the side handle to the desired position.

3. Tighten the side handle grip or ball securely.

Moving the Side Handle (Cat. No. 5426-21)

1. Remove the side handle by unscrewing the side

handle grip until it comes free.

2. Screw the side handle into the alternate loca-

tion.

3. Tighten the side handle grip securely.

Setting the Depth Gauge

1. Press in the clamp lever.

2. Slide the depth gauge rod backward or forward

until it is set for the desired depth.

NOTE: The drilling

depth is the distance

between the tip of the

bit and the tip of the

depth gauge rod.

3. Release the clamp le-

ver.

Installing Drill Bits and Chisels

Be sure that the shank of the bit is clean. Dirt par-

ticles may cause the bit to line up improperly. Do not

use bits larger than the maximum recommended

capacity of the drill because gear damage or mo-

tor overloading may result. For best performance,

be sure that the bit is properly sharpened and the

shank is lightly greased before use.

SDS Drive System

NOTE: Only use accessories with SDS or SDS

Plus shanks.

1. Unplug the tool.

2. Lightly grease the bit or chisel shank.

3. Insert the bit or chisel into the nose of the tool.

4. Rotate bit slowly until it aligns with the locking

mechanism.

5. Push bit into tool until it locks.

6. Check that the bit is locked properly; it should

be possible to pull the bit back and forth slightly

(about 1/4”).

7. To remove bits and chisels, pull bit holder toward

the rear of tool and remove bit.

NOTE: Use caution when handling hot bits and

chisels.

Electronic Feedback Control Circuit

These hammers have an Electronic Feedback

Control Circuit (EFCC) which helps improve the

operation and life of the tool. It allows the tool to

maintain constant speed and torque between no-

load and load conditions.

Soft Start

The Soft-Start feature reduces the amount of torque

reaction at startup to the tool and the user. This

feature gradually increases the motor speed up

from zero to the top no-load speed.

WARNING To reduce the risk of injury,

when using chisels or other hammering-

only accessories, the action selector must be

set to the "hammering only" position.

Selecting Mode

1. For hammering with

rotation, turn the selec-

tor lever to display the

hammer and twist drill

symbols. (Not available

on Cat. No. 5446-21)

2. For hammering only,

turn the selector lever

to display the hammer

symbol. (See "Selecting

Hammering Speed")

3. To freely rotate the bit

to the desired angle for

chiseling only, turn the

selector lever to display

the 0 symbol.

Fig. 2

Fig. 3

Fig. 4

Drilling

Depth

Fig. 1

Product specificaties

Merk:	Milwaukee
Categorie:	Boormachine
Model:	5426-21

Heb je hulp nodig?

Als je hulp nodig hebt met Milwaukee 5426-21 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Boormachine Milwaukee

Milwaukee M12 BDDXKIT Handleiding

16 November 2024

Milwaukee M18 FHACOD32 Handleiding

29 Mei 2024

Milwaukee M18 ONEFHP Handleiding

29 Mei 2024

Milwaukee M18 ONEFH Handleiding

29 Mei 2024

Milwaukee M18 CHM Handleiding

29 Mei 2024

Milwaukee M18 FHM Handleiding

29 Mei 2024

Milwaukee M18 ONEDD3 Handleiding

16 April 2024

Milwaukee SB 2-35 D Handleiding

10 April 2024

Milwaukee M18 BLH Handleiding

10 April 2024

Milwaukee M18 BLHX Handleiding

10 April 2024

Handleiding Boormachine

Nieuwste handleidingen voor Boormachine

Makita DDF459 Handleiding

21 December 2024

Total TRHLI1601 Handleiding

16 December 2024

Black Decker 1963 Handleiding

8 December 2024

Black Decker 1350-09 Handleiding

8 December 2024

Gude GTB 16/5 R Handleiding

8 December 2024

Hikoki DV36DA Handleiding

7 December 2024

Hikoki DH26PC2 Handleiding

7 December 2024

Hikoki DH28PCY2 Handleiding

7 December 2024

Zipper ZI-BHA1500DN Handleiding

7 December 2024

Bavaria BRH 850 Handleiding

5 December 2024