Milwaukee 4203 Handleiding
Milwaukee
Boormachine
4203
Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee 4203 (28 pagina's) in de categorie Boormachine. Deze handleiding was nuttig voor 56 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/28
HEAVY-DUTY DRILL MOTORS, ELECTROMAGNETIC DRILL STANDS,
ELECTROMAGNETIC DRILL PRESSES
PERCEUSES ÉLECTROMAGNÉTIQUES, COLONNES ET MOTEURS DE
PERCEUSES EXTRA ROBUSTES
MOTORES PARA TALADRADORAS EXTRARESISTENTES, BASES
ELECTROMAGNÉTICAS PARA TALADRADORAS, PRENSAS
TALADRADORAS ELCTROMAGNÉTICAS
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
Cat. No. / No de cat.
4253-1, 4262-1, 4292-1, 4297-1, 4204-1,
4206-1, 4208-1, 4210-1, 4202, 4203
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instruc-
tions, illustrations and specica-
tions provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, re and/or serious injury. Save all
warnings and instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of an GFCI reduces
the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your nger on
the switch or energizing power tools that have the
switch on invites accidents.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
• Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts. Loose clothes, jewelry or long hair
can be caught in moving parts.
• If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power
tool for your application. The correct power tool
will do the job better and safer at the rate for which
it was designed.
• Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
• Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many ac-
cidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
SERVICE
• Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
SPECIFIC SAFETY RULES
• When working overhead or on a vertical surface,
always use safety chain. Mounting can release.
(See “Safety Chain” under “Operation)
• Clean the surface before attaching the drill stand
to the work surface. Paint, rust, scale, or uneven
surfaces decrease the holding strength or the mag-
net. Chips, burrs, dirt and other foreign matter on
the surface of the magnetic base will also decrease
holding power.
3
• Do not attach magnetic base to nonmagnetic
grades of stainless steel. The magnetic base will
not hold. The electro magnetic drill press attaches
magnetically to any ferrous metal. It is designed for
use on 1/2 inch or thicker ferrous stock. Holding pow-
er will decrease on thinner stock. A back up plate must
be used (See “Backing Plate" under “Operation”).
• Wet connections are shock hazards. Prevent cut-
ting uid from traveling along the cord and contacting
the outlet, extension cord connections or tool plug.
• If the plug or connections get wet, turn power
off to the outlet before unplugging the tool.
• Use clamps or other practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body is
unstable and may lead to loss of control.
• Use only accessories that are recommended by
the manufacturer for your model. Accessories that
may be suitable for one tool, may become hazard-
ous when used on another tool.
• Always use common sense and be cautious when
using tools. It is not possible to anticipate every
situation that could result in a dangerous outcome.
Do not use this tool if you do not understand these
operating instructions or you feel the work is beyond
your capability; contact Milwaukee Tool or a trained
professional for additional information or training.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
•
WARNING
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
lter out microscopic particles.
EXTENSION CORDS
Grounded tools require a three wire extension
cord. Double insulated tools can use either a two
or three wire extension cord. As the distance from
the supply outlet increases, you must use a heavier
gauge extension cord. Using extension cords with
inadequately sized wire causes a serious drop in
voltage, resulting in loss of power and possible tool
damage. Refer to the table shown to determine the
required minimum wire size.
The smaller the gauge number of the wire, the greater
the capacity of the cord. For example, a 14 gauge
cord can carry a higher current than a 16 gauge cord.
When using more than one extension cord to make
up the total length, be sure each cord contains at
least the minimum wire size required. If you are using
one extension cord for more than one tool, add the
nameplate amperes and use the sum to determine
the required minimum wire size.
Guidelines for Using Extension Cords
• If you are using an extension cord outdoors, be sure
it is marked with the sufx “W-A” (“W” in Canada)
to indicate that it is acceptable for outdoor use.
• Be sure your extension cord is properly wired
and in good electrical condition. Always replace a
damaged extension cord or have it repaired by a
qualied person before using it.
• Protect your extension cords from sharp objects,
excessive heat and damp or wet areas.
Recommended Minimum Wire Gauge
For Extension Cords*
Nameplate Amps
Extension Cord Length
25' 50' 75' 100' 150'
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 16.0
16.1 - 20.0
18
18
18
18
16
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
--
18
16
14
12
10
--
--
16
14
12
12
--
--
--
* Based on limiting the line voltage drop to ve volts at 150%
of the rated amperes.
GROUNDING
WARNING
Improperly connecting the ground-
ing wire can result in the risk of
electric shock. Check with a qualied electrician
if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug pro-
vided with the tool. Never remove the grounding
prong from the plug. Do not use the tool if the
cord or plug is damaged. If damaged, have it
repaired by a MILWAUKEE service facility before
use. If the plug will not t the outlet, have a
proper outlet installed by a qualied electrician.
Grounded Tools (Three-Prong Plugs)
Tools marked “Grounding Required” have a three
wire cord and three prong grounding plug. The plug
must be connected to a properly grounded outlet
(See Figure A). If the tool should electrically mal-
function or break down, grounding provides a low
resistance path to carry electricity away from the
user, reducing the risk of electric shock.
The grounding prong in the plug is connected through
the green wire inside the cord to the grounding
system in the tool. The green wire in the cord must
be the only wire connected to the tool's grounding
system and must never be attached to an electrically
“live” terminal.
Your tool must be plugged into an appro-
Fig. A
priate outlet, properly installed and
grounded in accordance with all codes
and ordinances. The plug and outlet
should look like those in Figure A.
Double Insulated Tools (Two-Prong Plugs)
Tools marked “Double Insulated” do not require
grounding. They have a special double insulation
system which satises OSHA requirements and
complies with the applicable standards
Fig. B Fig. C
of Underwriters Laboratories, Inc., the
Canadian Standard Association and
the National Electrical Code. Double
Insulated tools may be used in either
of the 120 volt outlets shown in Figures
B and C.
Product specificaties
| Merk: | Milwaukee |
| Categorie: | Boormachine |
| Model: | 4203 |
Heb je hulp nodig?
Als je hulp nodig hebt met Milwaukee 4203 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Boormachine Milwaukee
16 November 2024
29 Mei 2024
29 Mei 2024
29 Mei 2024
29 Mei 2024
29 Mei 2024
16 April 2024
10 April 2024
10 April 2024
10 April 2024
Handleiding Boormachine
- Boormachine Bosch
- Boormachine IKEA
- Boormachine Panasonic
- Boormachine AEG
- Boormachine DeWalt
- Boormachine Baier
- Boormachine Basetech
- Boormachine Batavia
- Boormachine Bavaria
- Boormachine Berner
- Boormachine Black Decker
- Boormachine Blucave
- Boormachine Bort
- Boormachine Bruder Mannesmann
- Boormachine Defort
- Boormachine Delta
- Boormachine Dremel
- Boormachine Duro
- Boormachine Duro Pro
- Boormachine Ecomac
- Boormachine Economy
- Boormachine Einhell
- Boormachine Elu
- Boormachine Fe Powertools
- Boormachine Fein
- Boormachine Felisatti
- Boormachine Ferm
- Boormachine Ferrex
- Boormachine Festool
- Boormachine Flex
- Boormachine Gamma
- Boormachine Global
- Boormachine Goon
- Boormachine Gude
- Boormachine Hikoki
- Boormachine Hitachi
- Boormachine Holzmann
- Boormachine Huvema
- Boormachine Hyundai
- Boormachine Kawasaki
- Boormachine Kinzo
- Boormachine Kress
- Boormachine Laserliner
- Boormachine Lux Tools
- Boormachine Luxor
- Boormachine Maestro
- Boormachine Makita
- Boormachine Maktec
- Boormachine Max
- Boormachine Metabo
- Boormachine Parkside
- Boormachine Powerfix
- Boormachine Powerplus
- Boormachine Profitech
- Boormachine Protool
- Boormachine Robust
- Boormachine Rupes
- Boormachine Ryobi
- Boormachine Scheppach
- Boormachine Silverline
- Boormachine Skil
- Boormachine Sparky
- Boormachine Spit
- Boormachine Stanley
- Boormachine Stihl
- Boormachine Stomer
- Boormachine Tanaka
- Boormachine Texas
- Boormachine Toolcraft
- Boormachine Toolland
- Boormachine Topcraft
- Boormachine Trotec
- Boormachine Varo
- Boormachine Velleman
- Boormachine Vonroc
- Boormachine Westfalia
- Boormachine Workzone
- Boormachine Worx
- Boormachine Wurth
- Boormachine Zipper
- Boormachine Ozito
- Boormachine Clas Ohlson
- Boormachine Black And Decker
- Boormachine Steren
- Boormachine Cocraft
- Boormachine Meec Tools
- Boormachine Genesis
- Boormachine Carat
- Boormachine Eibenstock
- Boormachine Hilti
- Boormachine Cotech
- Boormachine Power Craft
- Boormachine Tacklife
- Boormachine Truper
- Boormachine Festo
- Boormachine Fieldmann
- Boormachine Mafell
- Boormachine Proxxon
- Boormachine Biltema
- Boormachine Malmbergs
- Boormachine Porter-Cable
- Boormachine Sun Joe
- Boormachine Dedra
- Boormachine Graphite
- Boormachine Narex
- Boormachine RIDGID
- Boormachine Tryton
- Boormachine Herkules
- Boormachine MSW
- Boormachine Sthor
- Boormachine Craftsman
- Boormachine Rikon
- Boormachine Cecotec
- Boormachine Verto
- Boormachine Alpha Tools
- Boormachine Hazet
- Boormachine G-Technology
- Boormachine Yato
- Boormachine Total
- Boormachine Stalco
- Boormachine Baumr-AG
- Boormachine Powerblade
- Boormachine Meister Craft
- Boormachine King Craft
- Boormachine Max Bahr
- Boormachine Toolson
- Boormachine Wolfcraft
- Boormachine Kreg
- Boormachine Rok
- Boormachine Netter Vibration
- Boormachine RUKO
- Boormachine Einhell Bavaria
- Boormachine McKenzie
- Boormachine Proviel
- Boormachine Ribimex
- Boormachine Ergotools Pattfield
- Boormachine MyTool
- Boormachine Rodcraft
- Boormachine Bavaria By Einhell
- Boormachine Handwerk
Nieuwste handleidingen voor Boormachine
21 December 2024
16 December 2024
8 December 2024
8 December 2024
8 December 2024
7 December 2024
7 December 2024
7 December 2024
7 December 2024
5 December 2024