Milwaukee 1007-1 Handleiding

Milwaukee Boormachine 1007-1

Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee 1007-1 (15 pagina's) in de categorie Boormachine. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/15

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S

MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN

COMPRENDRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL

MANUAL DEL OPERADOR.

Cat. No.

No de Cat.

1001-1

1007-1

1101-1

1107-6

1107-1

1250-1

3102-1

3102-6

3002-1

3107-1

3107-6

48-06-2871

48-06-2860

HEAVY-DUTY, REVERSING,

1/2" D-HANDLE DRILL

EXTRA ROBUSTE PERCEUSES

13 mm (1/2") ROTATION

RÉVERSIBLE, POIGÉE EN ÉNTRIER

HEAVY-DUTY, REVERSIBLES, TALADRO DE 13 mm (1/2") CON

EMPUNADURA EN “D”

HEAVY-DUTY, RIGHT ANGLE, REVERSING 1/2" D-HANDLE DRILL

EXTRA ROBUSTE PERCEUSES, COUDÉ-AD 13 mm (1/2")

ROTATION RÉVERSIBLE, POIGÉE EN ÉNTRIER

HEAVY-DUTY, REVERSIBLES, TALADROS EN ANGULOS

RECTOS, DE 13 mm (1/2") CON EMPUNADURA EN “D”

RIGHT ANGLE DRIVE UNIT

UNITÉ COUDÉE ANGLE DROIT

CABEZAL PARA TRANSMISSION DE POTENCIA EN ANGULO

RECTO

33° ANGLE DRIVE UNIT

RENVOI D’ANGLE DE 33°

UNIDAD IMPULSORA DE ANGULO DE 33°

2 3

PERSONAL SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WORK AREA SAFETY

ELECTRICAL SAFETY

WARNING READ ALL SAFETY WARNINGS AND INSTRUCTIONS.

Failure to follow the warnings and instructions may result in electric shock, ﬁ re and/or

serious injury. Save all warnings and instructions for future reference

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

POWER TOOL USE AND CARE

SPECIFIC SAFETY RULES

SERVICE

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive atmo-

spheres, such as in the presence of ﬂ ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁ ed plugs and matching outlets will

reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of elec-

tric shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet con-

ditions. Water entering a power tool will increase

the risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use

of a cord suitable for outdoor use reduces the risk

of electric shock.

• If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

these devices can reduce dust-related hazards.

• Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

• Do not use the power tool if the switch does

not turn it on and off. Any power tool that cannot

be controlled with the switch is dangerous and

must be repaired.

• Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

• Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may aﬀect the

power tool operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits

etc., in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the power

tool for operations diﬀerent from those intended

could result in a hazardous situation.

• Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

• Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inﬂ uence of drugs, alcohol or medi-

cation. A moment of inattention while operating

power tools may result in serious personal injury.

• Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

• Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your ﬁ nger on the switch or energising power

tools that have the switch on invites accidents.

• Wear ear protectors with impact drills. Expo-

sure to noise can cause hearing loss.

• Use auxiliary handles supplied with the tool.

Loss of control can cause personal injury.

• Hold power tools by insulated gripping sur-

faces when performing an operation where

the cutting tool may contact hidden wiring or

its own cord. Contact with a “live” wire will make

exposed metal parts of the tool “live” and shock

the operator.

• Keep hands away from all cutting edges and

moving parts.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

• WARNING Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are spe-

cially designed to ﬁ lter out microscopic particles.

Speciﬁ cations

Cat. No.

(RAD KIT)

1001-1

(3002-1)

1007-1

(***)

1101-1

(3102-1)

1107-1

(3107-1)

1107-6

(3107-6)

1250-1

(***)

Load

RPM

0-600

500

0-500

0-1000

RAD *

RPM

lo 0-400

hi 0-900

lo 0-400

hi 0-900

lo 0-335

hi 0-750

lo 0-335

hi 0-750

lo 0-335

hi 0-750

lo 0-665

hi 0-1500

Flat

boring

bit

1-1/2"

Auger

bit

1-1/2"

Ship

auger

bit

1-1/2"

1-1/16"

Wood

Volts

120

Hole

saw

4-1/2"

3-1/8"

Capacities

Selfeed

bit

3-5/8"

2-9/16"

3-5/8"

2-9/16"

3-5/8"

4-5/8"

2-9/16"

3-5/8"

4-5/8"

2-9/16"

3-5/8"

4-5/8"

2-9/16"

2-1/4"

Hole

saw

3-1/2"

4-1/2"

3-1/2"

4-1/2"

3-3/4"

3-1/2"

3-3/4"

3-1/2"

3-3/4"

3-1/2"

1-3/4"

Twist

drill

1/2"

Carbide-

tipped

bit

1/2"

Steel Masonry

33° **

RPM

0-600

500

0-500

0-1000

* The Right Angle Drill Kit can be purchased with some drills, or as an accessory.

** The 33° Angle Drill Kit is available as an accessory only (Cat. No. 48-06-2860).

*** RAD available as an accessory only (Cat. No. 48-06-2871).

Functional Description

1. Handle

2. Trigger

3. Nameplate

4. Extension (not shown)

5. Side handle

6. Keyed chuck

7. Side handle socket

8. Forward/Reverse switch

9. Quik-Lok® cord (Cat. No. 1007-1 and 1107-1)

10.Ring clamp

11.Right angle drive unit

12.Clamp

Cat. No. 1107-1

10 11

12 14

13.Auxiliary side handle

14.30" extension tube

15.33° angle drive unit

4 5

Grounded tools require a three wire extension

cord. Double insulated tools can use either a two

or three wire extension cord. As the distance from

the supply outlet increases, you must use a heavier

gauge extension cord. Using extension cords with

inadequately sized wire causes a serious drop in

voltage, resulting in loss of power and possible tool

damage. Refer to the table shown to determine the

required minimum wire size.

The smaller the gauge number of the wire, the

greater the capacity of the cord. For example, a 14

gauge cord can carry a higher current than a 16

gauge cord. When using more than one extension

cord to make up the total length, be sure each cord

contains at least the minimum wire size required. If

you are using one extension cord for more than one

tool, add the nameplate amperes and use the sum

to determine the required minimum wire size.

Guidelines for Using Extension Cords

• If you are using an extension cord outdoors,

be sure it is marked with the sufﬁ x “W-A” (“W”

in Canada) to indicate that it is acceptable for

outdoor use.

• Be sure your extension cord is properly wired

and in good electrical condition. Always replace

a damaged extension cord or have it repaired by

a qualiﬁ ed person before using it.

• Protect your extension cords from sharp objects,

excessive heat and damp or wet areas.

READ AND SAVE ALL

INSTRUCTIONS FOR FUTURE USE.

Recommended Minimum Wire Gauge

for Extension Cords*

Extension Cord Length

* Based on limiting the line voltage drop to ﬁ ve volts

at 150% of the rated amperes.

Nameplate

Amperes

0 - 2.0

2.1 - 3.4

3.5 - 5.0

5.1 - 7.0

7.1 - 12.0

12.1 - 16.0

16.1 - 20.0

25'

75'

100'

150'

50'

EXTENSION CORDS ASSEMBLY

WARNING To reduce the risk of injury,

always unplug tool before attaching

or removing accessories or making adjust-

ments. Use only speciﬁ cally recommended

accessories. Others may be hazardous.

Grounded Tools: Tools with Three Prong Plugs

Tools marked “Grounding Required” have a three

wire cord and three prong grounding plug. The

plug must be connected to a properly grounded

outlet (See Figure A). If the tool should electrically

malfunction or break down, grounding provides a

low resistance path to carry electricity away from

the user, reducing the risk of electric shock.

The grounding prong in the plug is connected

through the green wire inside the cord to the

grounding system in the tool. The green wire in the

cord must be the only wire connected to the tool's

grounding system and must never be attached to

an electrically “live” terminal.

Your tool must be plugged into an ap-

propriate outlet, properly installed and

grounded in accordance with all codes

and ordinances. The plug and

outlet should look like those in

Figure A.

Double Insulated Tools:

Tools with Two Prong Plugs

Tools marked “Double Insulated” do not require

grounding. They have a special double insula-

tion system which satisﬁ es OSHA requirements

and complies with the applicable standards of

Underwriters Laboratories, Inc.,

the Canadian Standard Asso-

ciation and the National Elec-

trical Code. Double Insulated

tools may be used in either of

the 120 volt outlets shown in

Figures B and C. Fig. B Fig. C

Fig. A

GROUNDING

WARNING Improperly connecting the

grounding wire can result in the risk of

electric shock. Check with a qualiﬁ ed electri-

cian if you are in doubt as to whether the

outlet is properly grounded. Do not modify

the plug provided with the tool. Never remove

the grounding prong from the plug. Do not

use the tool if the cord or plug is damaged. If

damaged, have it repaired by a MILWAUKEE

service facility before use. If the plug will not

ﬁ t the outlet, have a proper outlet installed by

a qualiﬁ ed electrician.

Removing and Replacing Quik-Lok

® Cords

MILWAUKEE's exclusive Quik-Lok® Cords provide

instant ﬁ eld replacement or substitution.

1. To remove the Quik-Lok® Cord, turn the cord nut

1/4 turn to the left and pull it out.

2. To replace the Quik-Lok

® Cord, align the connec-

tor keyways and push the connector in as far as

it will go. Turn the cord nut 1/4 turn to the right

to lock.

Installing Side Handle

MILWAUKEE D-Handle Drills are supplied with a

side handle that can be installed on either side of

the tool for right or left handed use. To install the

side handle, attach the side handle to the extension.

Thread it into the socket on the desired side of the

tool and tighten it securely. Because of the high

torque of this drill, the side handle must always be

used when operating the drill.

WARNING To reduce the risk of

injury, always use a side handle when us-

ing this tool. This tool operates with high

torque. Always brace or hold the tool securely.

WARNING When using the D-handle

drill without the right angle drive unit, do

not clamp the ring clamp with attached side

handle to the front of the gear case; use the

side handle instead.

Do not use the extension when using the

ring clamp.

For D-handle drill without Right Angle Drive Unit:

When using the D-handle drill without the right an-

gle drive unit, remove the ring clamp with attached

side handle, then remove the side handle from the

ring clamp. Attach the side handle to the extension.

The side handle can be installed on either side of

the tool for right or left handed use. To install the

extension with attached side handle, thread it into

the socket on the desired side of the tool (for right

or left-handed use) and tighten securely.

NOTE: If you have an extra ring clamp with at-

tached side handle and extension with attached

side handle, do not use the extension with attached

side handle when using the right angle drive unit.

Remove it from the tool.

Symbology

Volts Alternating Current

No Load Revolutions per

Minute (RPM)

Amperes

Mexican Approvals Marking

Underwriters Laboratories, Inc.,

United States and Canada Ring Clamp, Extension, and Side Handle for

Right Angle Drive Unit

For D-handle drill with Right Angle Drive Unit:

A ring clamp, extension, and side handle are sup-

plied with the Right Angle Drive Unit. When using a

right angle drive unit, attach the side handle to the

ring clamp. Do not use the extension when using

the ring clamp. The ring clamp with attached side

handle clamps onto the right angle drive unit and

can swivel 360° and locked tight in any position.

WARNING To prevent personal injury,

always remove the chuck key from the chuck

after each use.

Chuck jaws

Chuck key hole

Installing Bits into Keyed Chucks

Be sure that the shank of the bit and the chuck jaws

are clean. Dirt particles may cause the bit to line up

improperly. Do not use bits larger than the maxi-

mum recommended capacity of the drill because

gear damage or motor overloading may result. For

best performance, be sure that the bits are properly

sharpened before use.

1. Unplug the tool.

2. Open the chuck jaws wide

enough to insert a bit. Allow

the bit to strike the bottom of

the chuck. Center the bit in

the chuck jaws and tighten

the jaws by hand to align the bit.

3. Place the chuck key into each of the three holes

in the chuck, turning it clockwise to tighten the

chuck securely.

NOTE: Never use a wrench or means other than

a chuck key to tighten or loosen the chuck.

4. To remove the bit, insert the chuck key into one

of the holes in the chuck and turn it counterclock-

wise.

Removing the Chuck from the Drill

1. To remove the left-hand screw inside the chuck,

unplug the tool and open the chuck jaws. In-

sert a T-handle hex key

into the screw inside the

chuck. Turn the T-handle

hex key and remove the

screw. Save the screw

for installing your new

chuck.

2. To remove chuck; tighten a large hex key into

the chuck. Place the chuck on a workbench as

shown. Strike the hex key with a soft-headed

mallet to loosen the chuck. Remove the chuck

by hand.

Product specificaties

Merk:	Milwaukee
Categorie:	Boormachine
Model:	1007-1

Heb je hulp nodig?

Als je hulp nodig hebt met Milwaukee 1007-1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Boormachine Milwaukee

Milwaukee M12 BDDXKIT Handleiding

16 November 2024

Milwaukee M18 FHACOD32 Handleiding

29 Mei 2024

Milwaukee M18 ONEFHP Handleiding

29 Mei 2024

Milwaukee M18 ONEFH Handleiding

29 Mei 2024

Milwaukee M18 CHM Handleiding

29 Mei 2024

Milwaukee M18 FHM Handleiding

29 Mei 2024

Milwaukee M18 ONEDD3 Handleiding

16 April 2024

Milwaukee SB 2-35 D Handleiding

10 April 2024

Milwaukee M18 BLH Handleiding

10 April 2024

Milwaukee M18 BLHX Handleiding

10 April 2024

Handleiding Boormachine

Nieuwste handleidingen voor Boormachine

Makita DDF459 Handleiding

21 December 2024

Total TRHLI1601 Handleiding

16 December 2024

Black Decker 1963 Handleiding

8 December 2024

Black Decker 1350-09 Handleiding

8 December 2024

Gude GTB 16/5 R Handleiding

8 December 2024

Hikoki DV36DA Handleiding

7 December 2024

Hikoki DH26PC2 Handleiding

7 December 2024

Hikoki DH28PCY2 Handleiding

7 December 2024

Zipper ZI-BHA1500DN Handleiding

7 December 2024

Bavaria BRH 850 Handleiding

5 December 2024