Losi 1/24 Micro Rock Crawler RTR Handleiding

Losi Radiografisch bestuurbaar speelgoed 1/24 Micro Rock Crawler RTR

Lees hieronder de 📖 handleiding in het Nederlandse voor Losi 1/24 Micro Rock Crawler RTR (12 pagina's) in de categorie Radiografisch bestuurbaar speelgoed. Deze handleiding was nuttig voor 65 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

Operations Guide

CONNECT - REGISTER - WIN

updates, tech tips, service bulletins and more. Visit WWW.LOSI.COM and follow the

Product Registration link to stay connected.

For registering your Losi Product you will be automatically entered for a chance to win

the Losi Pick Your Prize Sweepstakes. The winner will be allowed to select a total prize

package of $1,000 (retail value) based on his/her preference.

Introduction

Thank you for choosing the Micro Rock Crawler from Losi. This guide contains the basic instruc-

tions for operating your new Micro Rock Crawler. While the Micro Rock Crawler is great for rst-

time RC drivers, it does require some mechanical experience. It is critical that you read all of the

instructions and all accompanying printed material in order to operate your model correctly and

avoid unnecessary damage. Please take a moment to look them over before running your model.

Warning

Although the best materials and components are used, and due to the size of this model, using anything other

than genuine Losi replacement and performance parts specically designed for the Losi Micro Rock Crawler could

cause damage.

1. Your Losi Micro Rock Crawler includes 2 complete

sets of batteries. The heavy-duty non-alkaline batter-

ies are for the transmitter.

2. Remove the battery cover by sliding it in the

direction noted on the cover. Install (8) AA alkaline

batteries into the bottom of the charger. Pay close

attention to the correct direction of the positive

(+) and negative(-) ends as marked. Reinstall the

battery cover.

3. Plug the battery lead into the charger lead. The

RED LED on the charger will light up and stay solid

while charging. When the battery is fully charged the

light will shut off (approximately 20 minutes). If the

charger light only lights up for about a minute, the AA

batteries inside the charger are low and should be

replaced.

4. Remove the transmitter battery cover by sliding it

in the direction noted on the cover. Install four (4) AA

batteries into the battery holder. Pay close attention to

the correct direction of the positive (+) and negative

(-) ends as marked. Once all 4 batteries have been

installed, reinstall the battery cover.

5. Plug in the battery lead into the speed controller

lead and replace the body. Secure the body with the

included body clips.

6. ALWAYS turn on the transmitter rst by sliding the

switch “ON”. The small red and green lights above the

switch should both light up. If not, please check for

low or incorrectly installed batteries.

7. Once the transmitter has been turned on, turn on the Losi Micro Rock Crawler by sliding the switch to the

“On” position (located at the rear of the chassis). If the wheels spin, adjust the “TH. Trim” knob located to

the lower right of the steering wheel until they stop. To go forward pull the trigger back. If you should need to

reverse, wait for the model to stop then push the trigger forward. When going forward the model should move

in a straight line. If not, adjust the “ST.Trim” so that it tracks in a straight line without having to turn the steer-

ing wheel. After you are nished running, turn the Losi Micro Rock Crawler off FIRST by sliding the switch to

the “Off” position. After the model has been turned off, turn off the transmitter.

RTR Getting Started

Charger

1. Your Losi Micro Rock Crawler includes a complete

set of batteries for the portable charger. 2. Remove the battery cover by sliding it in the

direction noted on the cover. Install (8) AA alkaline

batteries into the bottom of the charger. Pay close

attention to the correct direction of the positive

(+) and negative(-) ends as marked. Reinstall the

battery cover.

3. Plug the battery lead into the charger lead. The

RED LED will light up and stay solid while charging.

When the battery is fully charged the light will shut off

(approximately 20 minutes). If the charger light only

lights up for about a minute, the AA batteries inside

the charger are low and should be replaced. 4. Plug in the battery lead into the speed controller

lead and replace the body.

5. While pressing the white “Bind” button, slide the

switch to the “On” position. When the green LED

begins to ash rapidily release the bind button.

6. Switch on the transmitter and you should notice

a blinking LED on the back of the transmitter with a

translucent cover (MTX-Pro or LSR-3000). NOTE:

If using other Spektrum transmitters, please consult

your instruction manual for help with this process.

7. Once the transmitter has been bound with the Micro Rock Crawler on, if the wheels spin, adjust the “TH.

Trim” on your transmitter until they stop. To go forward pull the trigger back. If you should need to reverse,

push the trigger forward. When going forward the model should move in a straight line. If not, adjust the “ST.

Trim” so that it tracks in a straight line without having to turn the steering wheel. After you are nished run-

ning, turn the Losi Micro Rock Crawler off FIRST by sliding the switch to the “Off” position. After the model

has been turned off, turn off the transmitter.

Spektrum DX2, DX3 and radios equipped with Spektrum modules

are also compatible with Bind-N-Drive

Getting Started

Product specificaties

Merk:	Losi
Categorie:	Radiografisch bestuurbaar speelgoed
Model:	1/24 Micro Rock Crawler RTR
Gewicht:	188 g
Breedte:	86.36 mm
Capaciteit van de accu/batterij:	150 mAh
Frequentieband:	2.4 GHz
Batterijtechnologie:	Nikkel-Metaalhydride (NiMH)