Lanzar VCAP8000 Handleiding

Lanzar Niet gecategoriseerd VCAP8000

Lees hieronder de 📖 handleiding in het Nederlandse voor Lanzar VCAP8000 (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 272 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

DETAILED FEATURES:

a) Chrome plastic case

b) Flashing Blue LED Lights

c) 4 digits blue light display DV voltage meter that can measure 0.1DCV range.

d) Reverse pole connection PCB buzz warning function. If the capacitor is

connected incorrectly by reversing the positive and negative wires during the

installation process the PCB will issue a noise to warn you.

e) Over voltage limit and low battery voltage limit warning, When the system voltage

peeks over 17.5DCV or LESS than 10DCV. The buzzer on the PCB will issue an

audible noise warning.

f) When the voltage between the positive and negative keeps same in two minutes,

the display will turn to sleep. When the voltage changes, display will wake and show

the voltage, LED will ﬂicker.

INSTALLATION AND MOUNTING:

Securely mount the capacitor using supplied hardware. Notice the small mounting

screw hole in the capacitor chassis.

CHARGING THE CAPACITOR AND WIRING:

The capacitor must be charged before connecting the Power and Ground cables to

the capacitor. Failure to charge the capacitor will result in a large spark generated

from the rapid inﬂow of current.

To charge the capacitor:

1. Make Capacitor positive terminal connections with ampliﬁer and

tighten the bolt. Do not over-tighten the bolts!

Caution: Stripped terminals are not covered under the capacitor’s

warranty.

2. Connect the ground cable with battery, ampliﬁer, then refer to the

attached drawing.

3. Place the supplied charging resistor between positive terminal of

the capacitor and the battery’s positive terminal. Do this for 2~3

minutes or until the charging resistor goes out.

Caution: The charging resistor will get hot!

4. Immediately take out the charging resistor from the connecting

wire after the charging process. And connect the positive cable of

the battery directly to the positive terminal on the capacitor.

CHARGING

CAPACITOR WIRING DIAGRAM:

DISCHARGING THE CAPACITOR:

When you want to take out the capacitor after you ﬁnish the

installation process from original car audio system, you must do

discharge process when you want to move the capacitor. It will be

safe to release the power of the capacitor.

To discharge the capacitor: With battery power disconnected, place

the resistor across the capacitor’s positive and negative terminals,

after 1-5 minutes, the capacitor will be discharged. (The resistor will

become hot!) Then you can safely remove and handle it..

DISCHARGING

LIMITED WARRANTY

One Year Warranty from the date of purchase.

WARNING!!

THIS POWER CAPACITOR MAY EXPLODE AND CAUSE

SERIOUS INJURY IF ABUSED OR CONNECTED IMPROPERLY.

PLEASE REFER TO THE INSTRUCTIONS CONTAINED IN THIS

MANUAL FOR CORRECT MOUNTING,

CHARGING/DISCHARGING AND WIRING CONNECTION FOR

THIS CAPACITOR PRIOR TO INSTALLATION.

SPECIFICATIONS

Capacitance……………………….….. 12,000,000 micro farad

Working Voltage……………………… 19DC

Surge Voltage…………………………. 24DC

E.S.R (Equivalent Series Resistance)… 0.0015 ohm @120hz/ 25 ℃

Capacitance Tolerance………………... ±10%

Model: VCAP3000

30Farad Hybrid High Performance Capacitor

Capacitance……………………….….. 30,000,000 micro farad

Working Voltage……………………… 19DC

Surge Voltage…………………………. 24DC

E.S.R (Equivalent Series Resistance)… 0.0015 ohm @120hz/ 25 ℃

Capacitance Tolerance………………... ±10%

Model: VCAP5000

50Farad Hybrid High Performance Capacitor

Capacitance……………………….….. 50,000,000 micro farad

Working Voltage……………………… 19DC

Surge Voltage…………………………. 24DC

E.S.R (Equivalent Series Resistance)… 0.0015 ohm @120hz/ 25℃

Capacitance Tolerance………………... ±10%

Model: VCAP8000

80Farad Hybrid High Performance Capacitor

Capacitance……………………….….. 80,000,000 micro farad

Working Voltage……………………… 19DC

Surge Voltage…………………………. 24DC

E.S.R (Equivalent Series Resistance)… 0.0015 ohm @120hz/ 25 ℃

Capacitance Tolerance………………... ±10%

Model: VCAP10000

100Farad Hybrid High Performance Capacitor

Capacitance……………………….….. 100,000,000 micro farad

Working Voltage……………………… 19DC

Surge Voltage…………………………. 24DC

E.S.R (Equivalent Series Resistance)… 0.0015 ohm @120hz/ 25℃

Capacitance Tolerance………………... ±10%

12Farad Hybrid High Performance Capacitor

Model: VCAP1200

Product specificaties

Merk:	Lanzar
Categorie:	Niet gecategoriseerd
Model:	VCAP8000
Kleur van het product:	Chroom
Breedte:	177.8 mm
Hoogte:	76.2 mm
Montagewijze:	Opbouw
Soort voeding:	DC
Impedantie:	0.0015 Ohm
Spanning:	19 V
Capaciteit:	80.000.000
Bedrijfstemperatuur (T-T):	0 - 25 °C
Capaciteit tolerantie:	10 procent
Condensator type:	Fixed capacitor