Lanzar OptiX-6 Handleiding

Lanzar Niet gecategoriseerd OptiX-6

Lees hieronder de 📖 handleiding in het Nederlandse voor Lanzar OptiX-6 (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

- 1 -

Congratulations on your purchase of a Crossover. This product has been designed LANZAR

and built to deliver excellent sound quality and long lasting high performance. We are sure you

will enjoy listening to your favorite music with this component in your car audio System. LANZAR

For best result a professional car stereo installer for application advice or troubleshooting. Thank

you for choosing products for your auto-sound system. Everything else is just noise LANZAR

INTRODUCTION

FEATURES

SUBWOOFER CHANNEL:

* +12dB Bass Boost

* Phase Shift Switch

* Stereo/Mono Switch

* Output Level Control

* Exclusive Remote Subwoofer Level Control

* Low Pass Frequency Selector 50Hz to 160Hz

* Bass Boost Frequency Selector 40Hz to 120Hz

FRONT AND REAR CHANNEL:

* High Pass Frequency Selector

32Hz to 800Hz

* Frequencies Multiplier p2-x1 or x10

* Signal Gain Control

SPECIFICATIONS

Power Supply : 14.4 volts DC negative ground

Input current 0.5 amp max：

Distortion 0.01：％ THD at 1V output level

Frequency response 10Hz- 30K Hz, ±3dB：

S/N ratio (A weighted) > 95 dB：

Separation 60 dB：

Crossover frequencies (continuously variable)：

Front High-pass： (x1) : 32-800 Hz (x10) : 320Hz- 8KHz

Rear High-pass： (x1) : 32-800 Hz (x10) : 320Hz- 8KHz

Subwoofer： 50-160 Hz

Crossover slope rate： 12 dB per octave 2nd Order Butter worth

Subwoofer boost： Single octave 0 dB to 12 dB (variable) at 40 to 120Hz (variable)

Input impedance > 10K Ohms：

Output impedance < 1K Ohms：

Output gain +3 dB：

Output voltage level 5 volts max：

Dimensions： 150mm x 190mm x 35mm

1. Find a suitable location in the vehicle to mount the crossover.

2. Bolt the crossover to the mounting surface.

3. Using the screw terminals provided, connect minimum 16 gauge wire from the power,

Ground and remote terminals. Connect the shortest possible wire to a chassis ground point. The (+)

12V connection should be made directly to the car battery, and the remote should be connected to

the Remote Turn On Lead of your head unit. When connecting directly to the battery, install a 1A

Fuse within 18 inches of the battery terminal.

4. Connect all line inputs and outputs using high-quality RCA cables.

5. Recheck all connections before powering up.

6. Set all level controls to their minimum positions and set all crossover controls, switches, etc. To

the desired frequency or position.

7. Once the system is powered up, set the volume control on the head unit to a moderate level where

your normal speaking voice can be heard while the music is playing.

8. Further fine tuning of the various controls may be necessary to obtain the desired results.

9. When unsure about installation or system tuning, please consult an authorized LANZAR dealer.

INTALLATION

- 2 -

CONTROLS AND OPERATION

LEFT/RIGHT FRONT CHANNEL SIGNAL INPUTS:

To be connected to the front channel output of the source

unit.

1.POWER INPUT TERMINAL(12V): To be connected to the positive terminal of your vehicle

battery or other constant +12V source.

2.GROUND INPUT TERMINAL: To be wired to the vehicle's chassis ground.

3.REMOTE TURN-ON INPUT TERMINAL(REMOTE): To be connected to the remote control wire or

antenna lead of the source unit for remote ON/OFF.

4. POWER INDICATOR: This indicator lights up when the internal switching power supply is activated and the

unit is operational.

Set to “IN” position the input signals coming in through the front channel signal inputs are split

and directed to the front and rear channels simultaneously. (This feature is to be engaged where

the source unit has no separate front, rear or subwoofer channel outputs)

If the source unit has independent front and rear channel outputs, disengage the parrel input by

sliding the switch to the position“OUT”

8. LEFT/RIGHT DUAL IN/OUT TERMINALS

As Input Terminal:

To be connected to the subwoofer output of the source unit.

As Output Terminal:

To be connected to the front channel input terminal of another electronic

crossover in a multi-crossover system.

7. LEFT/RIGHT REAR CHANNEL SIGNAL INPUTS:

To be connected to the rear channel outputs of the source

unit. BUT MAKE SURE THAT THE DUAL INPUT SWITCH IS AT THE OUT POSITION.

6. DUAL INPUT SWITCH

Product specificaties

Merk:	Lanzar
Categorie:	Niet gecategoriseerd
Model:	OptiX-6
Kleur van het product:	Zwart
Breedte:	150 mm
Diepte:	190 mm
Hoogte:	35 mm
Geschikt voor:	3-wegsystemen
Impedantie:	10000 Ohm
Signaal/ruis-verhouding:	95 dB
Uitgangsspanning (max):	5 V
Totale harmonische vervorming (THD):	0.01 procent
Niveaucontrole subwoofer:	Ja
Variabele basboost:	Ja
Kantelfrequentie:	32 - 800 Hz
Variabel hoogdoorlaatfilter:	Ja
Variabel laagdoorlaatfilter:	Ja