Lanzar OPTIX5 Handleiding

Lanzar Niet gecategoriseerd OPTIX5

Lees hieronder de 📖 handleiding in het Nederlandse voor Lanzar OPTIX5 (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 50 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

- 1 -

FRONT AND REAR CHANNEL : SUBWOOFER CHANNEL:

* High Pass Frequency Selector * Subwoofer Input Switch

40Hz to 400Hz / 32Hz to 250Hz * +12dB Bass Boost

* Frequencies Multiplier p2-x1 or x20 * Phase Shift Switch

* Crossover Slope 6dB/Octave or * Stereo/Mono Switch

12dB/Octave * Output Level Control

* Signal Gain Control * Exclusive Remote Subwoofer Level Control

* Parallel Input Switch * Low Pass Frequency Selector 40Hz to 400Hz

* Bass Boost Frequency Selector 25Hz to 250Hz

Power Supply....................................... DC to DC switching power

S/N Ratio............................................. 110dB

Channel Separation.............................. 80dB

Distortion.............................................. THD @ 0.01%

Crossover Slope.................................... 12dB per Octave

Input Impedance................................... 20K Ohms

Output Impedance................................ 100 Ohms

Output Gain.......................................... 1:2 (+6dB)

Output Voltage Level........................... 8Volts Max

Dimensions.......................................... 5-13/16" (W) x 8-1/4" (L) x 1-3/8" (H)

1. Find a suitable location in the vehicle to mount the crossover.

2. Bolt the crossover to the mounting surface.

3. Using the screw terminals provided, connect minimum 16 gauge wire from the power,

Ground and remote terminals. Connect the shortest possible wire to a chassis ground point. The (+)

12V connection should be made directly to the car battery, and the remote should be connected to

the Remote Turn On Lead of your head unit. When connecting directly to the battery, install a 3A

Fuse within 18 inches of the battery terminal.

4. Connect all line inputs and outputs using high-quality RCA cables.

5. Recheck all connections before powering up.

6. Set all level controls to their minimum positions and set all crossover controls, switches, etc. To

the desired frequency or position.

7. Once the system is powered up, set the volume control on the head unit to a moderate level where

your normal speaking voice can be heard while the music is playing.

8. Further fine tuning of the various controls may be necessary to obtain the desired results.

9. When unsure about installation or system tuning, please consult an authorized dealer.LANZAR

INSTALLATION

FEATURES

SPECIFICATIONS

Features and specifications subject to change without notice.

Congratulations on your purchase of a Crossover. This product has been designed LANZAR

and built to deliver excellent sound quality and long lasting high performance. We are sure you

will enjoy listening to your favorite music with this component in your car audio System. LANZAR

For best result a professional car stereo installer for application advice or troubleshooting. Thank

you for choosing products for your auto-sound system. Everything else is just noise LANZAR

INTRODUCTION

- 2 -

CONTROLS AND OPERATION

1. Ground Terminal (GND).

2. Remote Turn-On Terminal (REM).

3. Power Terminal (+12V).

4. Power Indicator.

5. Front Channel Inputs.

6. Parallel Input Switch: If there are 4 sets (2 pairs/ Front & Rear) RCA inputs available, place

this switch in the "IN" position. If there is only one pair of input RCA connectors being used,

place this switch in the "OUT" position to provide Front and Rear input from that single pair of

RCA inputs.

(Note that the Front inputs are essentially the main inputs, thus providing an input to

these terminals, and properly selection of the various switch positions would provide

signals on ALL of the various outputs.)

7. Rear Channel Inputs.

8. Subwoofer Channel Inputs.

9. Subwoofer Input Switch: If there is no dedicated subwoofer signal available from the signal

source, place this switch in the "ON" position to provide signal at the subwoofer output terminals.

If there is a dedicated subwoofer signal source available for this input purpose, place the switch

in the "OFF" position.

Product specificaties

Merk:	Lanzar
Categorie:	Niet gecategoriseerd
Model:	OPTIX5
Kleur van het product:	Zwart
Breedte:	127 mm
Diepte:	203.2 mm
Hoogte:	25.4 mm
Geschikt voor:	2-weg/3-wegystemen
Impedantie:	100 Ohm
Signaal/ruis-verhouding:	110 dB
Uitgangsspanning (max):	8 V
Type product:	Actieve crossover