La Crosse Technology WT-3143AX1 Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor La Crosse Technology WT-3143AX1 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Model: WT-3143A www.lacrossetechnology.com/support Page | 1
Model: WT-3143A
Instruction Manual
DC: 0 31716
14” Atomic Wall Clock
Get Started
1: Slide the switch to select a time zone and DST ON or OFF .
2: Insert 1 fresh AA, LR6 1.5 volt ALKALINE battery according to the polarity
marked on the case.
OPTIONAL: To extend battery life (over years) 3 , insert two batteries in the
compartment below the movement.
3: For the best reception, please place clock on a wall that faces Ft. Collins,
Colorado. During the night, your clock will automatically set itself.
Note: The hands will move to the 12:00 position and for the radio signal. search
If the radio signal not received is in the first 10 minutes, the clock will start
running from the 12:00 position and will continue to run. Do not attempt to
reset the hands manually even though the time on the clock is incorrect. The
clock is synchronizing to the WWVB signal and once the radio signal is decoded,
the hands will automatically adjust to the correct time. This may take up to 5
nights if there is atmospheric interference.
Position Clock
• Signal reception is at its peak when there is only one wall or window
between the clock and the outside.
• The antenna is best positioned for signal reception when the front or back of
the clock faces Colorado.
• Choose a location 6 feet or more from electronics such as cordless phones,
wireless gaming systems, televisions, microwaves, routers, baby monitors,
etc., which can prevent signal reception.
• Large office buildings, schools, or hospitals may not receive the WWVB time
signal in every room.
Time Zone
DST ON/OFF
Model: WT-3143A www.lacrossetechnology.com/support Page | 2
• Building with a metal roof may interfere with reception.
R :eset If the clock does not respond to the various function modes, reset the
clock by pressing the RESET button on the movement case.
Manual Set Time
On rare occasions in certain areas, the clock may not be
able to utilize the radio controlled function because of the
strength of the signal or the geographic location. In this
case, the clock can be set manually and used as a regular
quartz wall clock.
Note: Allow up to five nights for the clock to receive the WWVB signal before
manually setting the time.
Set the clock manually:
1. Press and hold the SET button for 3+ seconds to activate the manual mode.
Once the clock is in manual mode, there are two ways to move the minute
hand forward.
2. Hold the SET button down to move the minute hand forward consistently.
3. Alternatively, press the SET button rapidly (more than once per second) to
move the minute hand forward step by step (in minute increments).
4. Use these features to move the minute hand forward until the correct time is
set. The clock will automatically leave manual mode after the SET button is
not pressed for 6+ seconds.
Troubleshooting
The wonderful advantage of owning a radio-controlled clock is that it is virtually
trouble free. If the clock receives a clear time signal, it will set itself perfectly. If it
does not receive a time signal, consider the following:
• Battery – The clock must have a fresh battery to receive and process the
time signal.
• Location – Try a different location, ideally near a window. Your clock should
be at least six feet from computers, TVs, air conditioners, other radio-
controlled clocks and other electrical appliances that cause interference.
• Weather – Electrical storms between you and Colorado during the night will
interfere with the WWVB signal.
Daylight Saving Time:
The National Institute of Standards and Technology and WWVB encode a special
DST “bit” in the WWVB transmission for DST. Your clock will read this information
and automatically advance the hands one hour in the spring and eleven hours in
the fall.
Arizona
If you live in an area that does not recognize DST, you must slide the DST switch
OFF. To reactivate the DST program simply slide the switch to the ON position.
Model: WT-3143A www.lacrossetechnology.com/support Page | 3
Manual WWVB Time Signal Search
For information about WWVB, visit: www.nist.gov/pml/div688/grp40/wwvb.cfm
Manual Signal Search:
The WWVB signal is strongest at night.
• Hold the WAVE button down for 3+ seconds.
• The hands will automatically reset to the 12:00 position, and the movement
will search for the WWVB time signal from Fort Collins, CO.
• If the movement successfully receives the signal, the clock will reset
automatically to the correct time. The signal search takes approximately 3-8
minutes.
• Set the clock manually and the movement's micro CPU will control the time , -
keeping function.
Internal Synchronization:
Once the clock has set correctly by the radio signal, the clock’s CPU operates
continuously. To ensure accuracy, the clock synchronizes the position of the
second and minute hands to the time calculated by the CPU every day. Second
hand synchronization occurs at 1:30 a.m. and 9:30 a.m. and minute hand
synchronization occurs between 1:50 and 2:01 am every day.
Signal Interference:
In some cases, the signal is affected by weather conditions and electrical
interferences, or the location of the clock itself may result in poor reception. If the
clock has not synchronized to the correct time within a few days of activation, you
may need to move the clock to a different location.
Frequently Asked Questions
Q. How long will the battery last?
A. One good AA alkaline battery will last over 12 years with months, and over 3
the optional, 2 additional batteries.
Q: Can I wire a control timing circuit to the La Crosse Technology® atomic
clock?
A: No, the clock cannot work on a timing circuit. Opening the clock voids the
warranty.
Q: Is there a booster antenna to receive the WWVB signal in a difficult
location?
A: No, the clock cannot work with a booster antenna. Opening the clock or
movement voids the warranty.
Q: Can I shut off the WWVB signal?
A: No. If you manually set the time, when the clock receives a WWVB signal,
that signal will override the manual set. The WAVE button will temporarily
stop a WWVB search, but will not permanent stop the clock from receiving a
WWVB time signal.


Product specificaties

Merk: La Crosse Technology
Categorie: Niet gecategoriseerd
Model: WT-3143AX1

Heb je hulp nodig?

Als je hulp nodig hebt met La Crosse Technology WT-3143AX1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd La Crosse Technology

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd