La Crosse Technology WS-6010U-IT Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor La Crosse Technology WS-6010U-IT (9 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 247 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/9
1
Wall
mount
Solar
panel
Battery
compartment
with battery
switch inside
Model WS- -6010U IT
Solar Powered Wireless Humidity/Temperature Station
(Weather Station)
INSTRUCTION MANUAL
Model TX62UTH-IT/Solar-powered Transmitter (Sensor):
D toggles temperature and humidity readings LC
Transmits outdoor humidity/temperature to indoor receiver using 915
MHz signals
200 FT. wireless transmission range (open air)
Built-in rechargeable alkaline power cells store solar power for
continuous operation
No batteries necessary (internal power cells cannot be replaced;
contact customer service for a replacement sensor)
Able to charge in low light environments.
Solar panel
2
BATTERY
COMPARTMENT
INITIAL SETUP (USING INCLUDED SOLAR RECHARGEABLE BATTERIES FROM THE FACTORY)
1. Open battery compartment on the back of the Weather Station and make sure that the battery switch
under the battery compartment is to the left. If it is not, please slide the switch to the left before
proceeding.
2. Locate the battery insulator tab and gently pull to remove it.
3. Slide the battery switch to the SOLAR position.
4. Continue to section labeled " " ACTIVATE SOLAR-POWERED OUTDOOR TRANSMITTER
ACTIVATE SOLAR-POWERED OUTDOOR TRANSMITTER
Press the RESET key on the Sensor to activate the solar-powered transmitter and place it 5-10 feet
from the Weather Station for 15 minutes. The outdoor temperature will show on the weather station
within 60 seconds. Allow the sensor and the weather station to sit 5-10 feet apart for 15 minutes so the
signal can lock in repeatedly. Do not press buttons at this time.
NOTE: The solar panel needs light from a 60W light bulb or brighter during the activation process. Do not
cover solar panel with hands or other objects.
TX62UTH-IT transmitter RESET key:
NOTE: Do not use sharp objects to
press the RESET key. Use a small
dull pointed object or a straightened
paper clip and
gently press the
RESET key to commence NORMAL
MODE.
Several start up numbers will ash on
the screen of the sensor then the
temperature will display.
SWITCH RIGHT
(SOLAR OPERATION)
(SOLAR-RECHARGEABLE
BATTERIES)
Slide switch to RIGHT
position once solar-
rechargeable
batteries are inserted and
insulator tab is removed
WARNING
Do NOT recharge the
included solar-
rechargeable batteries
outside of this product
because it will damage
the batteries and other
charging devices.
SWITCH LEFT
(START-UP / RESET)
(STANDARD
ALKALINES)
Slide switch to LEFT
position before (1) start-
up / reset or (2) any type
of battery replacement
3
SOLAR-POWERED TRANSMITTER OPERATION MODES
(1) NORMAL MODE:
NORMAL MODE occurs when the battery voltage is 2.5V or greater.
It measures and transmits temperature / humidity (weather) data to the indoor receiver every
8 seconds.
It checks the brightness level of the surrounding environment every 5 seconds.
It measures / transmits every 16 seconds if it detects a dark environment or if the battery
voltage drops below 2.5V.
(2) IDLE MODE:
If the battery voltage drops below 2.4V, it commences IDLE MODE; the LCD turns o and it
does not measure / transmit weather data.
It checks the brightness level of the surrounding environment every 5 seconds.
If battery voltage rises back to 2.5V or above, it returns to NORMAL MODE.
If the environment remains dark for 72 hours, it commences STOP MODE.
(3) STOP MODE (STANDBY):
Occurs when the environment remains dark for 72 hours OR if you manually commence
STOP MODE (standby) by covering the solar cell for 10 seconds and then press the RESET
key one time.
*NOTE: The LCD will display " " then turn off and commence STOP MODE. StP
While in STOP MODE (standby), the LCD is o and the Sensor does not perform any normal
operations.
To resume normal operation, ensure the Sensor is in a bright environment (next to a 60W
light bulb or similar condition) and press the RESET key to return to NORMAL MODE (battery
voltage is higher than 2.5V).
SOLAR MODE ON THE WEATHER STATION
This weather station has green technology and a power-savings mode that reduces power consumption
by monitoring and reacting to available lighting conditions .
The surrounding environment brightness is checked every 5 seconds.
LCD will automatically turn OFF if the environment is too dark. (It will appear blank)
LCD will automatically turn ON if the environment is bright enough.
No information will display when the LCD is OFF, but all the settings and operations will
remain, except for the temperature and humidity measurements.
This will occur no matter which type of battery you use. This is a NOTE: Program Menu
feature.
Turn this feature o and the LCD will stay on all the time. Enter the Program Menu and click
through until you see SOL and ON flashing. Press the PLUS button to turn Solar Mode OFF.
The LCD will no longer go blank in low light situations.
STOP MODE ON THE WEATHER STATION
If the Weather Station is in a dark environment for 72 hours continually, the clock will go to the stop mode:
The most power saving condition.
The indoor solar display will not operate and the LCD will turn OFF.
Press any key to wake up the indoor solar display and re-activate the transmission with the
solar transmitter.


Product specificaties

Merk: La Crosse Technology
Categorie: Niet gecategoriseerd
Model: WS-6010U-IT

Heb je hulp nodig?

Als je hulp nodig hebt met La Crosse Technology WS-6010U-IT stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd La Crosse Technology

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd