La Crosse Technology LTV-R2 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor La Crosse Technology LTV-R2 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Model: LTV-R2
DC: 090517
Rain Sensor
Insert 2- AA batteries into the rain sensor according to polarity.
1. Flip open both locking tabs on your rain sensor and lift o the funnel portion.
2. Pull up on the battery cover and remove.
3. Install 2-AA batteries according to polarity. Reposition the battery cover over the battery compartment,
andrmly push down to lock it back into place
5. Remove cardboard and any tape around the rocker before use. These were used to protect the
sensor from unwanted movement during shipping.
6. Place the funnel portion back over the sensor and re-secure the locking tabs.
Power
Funnel
Battery Cover
Locking Tab
Remove piece under
rocker of rain sensor
Position Rain Sensor
LTV-R2 Rain Sensor
Lets identify the parts of the rain sensor.
• Mount your rain sensor in an open area for a more accurate rain count.
• Placing the rain sensor on the ground provides the most accurate rainfall measurement as there is no
wind shear. Unfortunately, since insects think of rain sensors as personal hotels, placing your sensor
3-6 feet above ground may deter the insects.
• This is a self-emptying sensor, but be sure your unit is not sitting in a depression that would prevent
rain from draining out of the bottom
• Your rain sensor should be accessible to allow for periodic cleaning of leaves or other debris that may
clog the funnel.
• Install the Rain sensor on a level platform that is stationary and has a direct line of sight to your station.
• Insert mounting screws through the holes in the base of the rain sensor. Do not over tighten.
• Use the bubble level inside your sensor to be sure it is level.
• Avoid other wireless rain sensors as this can cause inaccuracy due to signal interference.
• The maximum wireless transmission range to the rain station is over 400 feet (121 meters) in open air,
not including walls or floors.
• For video instruction, please visit: http://bit.ly/Rain_SensorMounting
AA
+
-
AA
+-
Top (Funnel)
Battery Cover
Locking Tabs
Rocker
Mounting Screw (3 total) Bubble Level
Clean Rain Sensor
1. Press the Locking Tabs on each end and lift o the funnel.
2. Gently remove debris or insects inside the rain sensor.
3. Clear debris from drain vents.
4. Clear debris from the rain funnel itself.
5. Reinstall the rain funnel.
Note: Do not oil the rain sensor.
Sensor ID
Standalone station:
Your rain sensor has a bar code and ID number. This ID number locks your sensor into
your station. Follow the instructions in your station manual to delete the sensor ID
for sensor replacement.
La Crosse View™ compatible system:
The rain sensor ID and bar code are recognized by the La Crosse View™ app if you are using
this rain sensor as an add-on to your existing La Crosse View™ compatible system.
To add this sensor to your existing La Crosse View™ compatible system:
1. Open your La Crosse View app to add sensors.
2. From Main Menu - select “Devices” under “Add/Edit”
3. On Edit Devices page - select “ADD DEVICE”
4. Scan Device ID - Scan the bar code on your sensor or press inside the Device ID search box to enter
your code manually. Once entered, select “Search”.
5. On Confirm Device page - Confirm the sensor image and model number are correct and select “YES”
6. On Enter Device and Location Names page - enter Device Name and select a location or enter
a Location Name for your sensor. Select “DONE”.
Note: This rain sensor cannot connect to the La Crosse View app without a La Crosse View compatible
station. Station’s that are La Crosse View compatible have built-in Wi-Fi capabilities that send your rain
sensor’s data to the La Crosse View app. For more information about our new connected stations visit:
http://www.lacrossetechnology.com/products/connected
Note: When multiple rain sensors are used in close proximity false readings may occur.
JOIN THE CONVERSATION
Follow us on our social media outlets for the latest promotions, product support, and awesome
giveaways.
Let’s Be Social!


Product specificaties

Merk: La Crosse Technology
Categorie: Niet gecategoriseerd
Model: LTV-R2

Heb je hulp nodig?

Als je hulp nodig hebt met La Crosse Technology LTV-R2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd La Crosse Technology

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd