Joy-it COM-OLED2.42 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Joy-it COM-OLED2.42 (16 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 10 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/16
www.joy it.net-
Pascalstr. 8 47506 Neukirchen Vluyn-
OLED DISPLAY MODULE-
COM OLED2.42-
1. GENERAL INFORMATION
Dear customer,
thank you very much for choosing our product.
In the following, we will introduce you to what to observe while starting
up and using this product.
Should you encounter any unexpected problems during use, please do
not hesitate to contact us.
www.joy it.net-
Pascalstr. 8 47506 Neukirchen Vluyn-
2. PIN ASSIGNMENT OF THE DISPLAY
Pin Designation Pin number I/O Function
VSS 1 P Logic circuit ground
This is a ground pin. It also serves as a reference
for the logic pins. It must be connected to the
external ground.
VDD - 2 3,3 5V Power supply for display module circuit
This is a power supply pin.
V0 - 3 Voltage supply for OEL panel
This is the most positive voltage supply pin of
the chip.
Please do not connect it.
A0 4 I Data/Command Control
This pin is a data/command control pin. When
the pin is pulled high, the input at D7~D0 is trea-
ted as display data. When the pin is pulled low,
the input at D7~D0 is transferred to the com-
mand register.
/WR 5 I Read/Write Select or Write
This pin is an MCU interface input. When
connected to a 68XX series microprocessor, this
pin is used as a read/write select (R/W) input.
Pull this pin high for read mode and pull it low
for write mode. When the 80XX interface mode is
selected, this pin is the write input (WR). The da-
ta write operation is initiated when this pin is
pulled "Low" and CS is pulled "Low".
/RD 6 I Read/Write Enable or Read
This pin is an MCU interface input. When
connected to a 68XX series microprocessor, this
pin is used as an Enable(E) signal. The read/
write operation is initiated when this pin is pul-
led high and CS is pulled low. When connected
to an 80XX microprocessor, this pin receives the
Read(RD) signal. The data read operation is initi-
ated when this pin is pulled low and CS is pulled
low.
www.joy it.net-
Pascalstr. 8 47506 Neukirchen Vluyn-
Pin Designation Pin number I/O Function
DB0 7 I/O
Host data input/output bus
These pins are bidirectional 8 bit data buses -
that connect to the microprocessor data
bus. When serial mode is selected, D1 is the
SDIN serial data input and D0 is the SCLK
serial clock input.
DB1 8 I/O
DB2 9 I/O
DB3 I/O 10
DB4 I/O 11
DB5 I/O 12
DB6 I/O 13
DB7 I/O 14
/CS I Chip Select 15 -
This pin is the chip select input. The chip is
only enabled for MCU communication when
CS# is pulled low.
/RESET I Power Reset for Controller and Driver 16
This pin is a reset signal input. When the pin
is low, the initialization of the chip is perfor-
med.
NC (BS1) H/L Communication protocol selection 17
These pins are inputs for selecting the MCU
interface.
See the following table:
NC (BS2) H/L 18
NC 19 - NC or connection to VSS.
FG 20 0V It must be connected to external ground.
68XX-
parallel
80XX-
parallel
I2C Serial
BS1 0 1 1 0
BS2 1 1 0 0


Product specificaties

Merk: Joy-it
Categorie: Niet gecategoriseerd
Model: COM-OLED2.42

Heb je hulp nodig?

Als je hulp nodig hebt met Joy-it COM-OLED2.42 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Joy-it

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd