IOptron HAE16C Handleiding

IOptron Statief HAE16C

Lees hieronder de đź“– handleiding in het Nederlandse voor IOptron HAE16C (6 pagina's) in de categorie Statief. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6
1
iOptron Corp. | 1 Merrill Street | Woburn, MA01801USA | (781) 569-0200 | Toll Free (866) 399-4587 | www.iOptron.com
Quick Start Guide
HAE16C Dual AZ/EQ SWG Hybrid Mount
PACKAGE CONTENTS1
ď‚· Telescope mount HAE16C w/built-in Wi- Fi
 AC adapter -240V, 12V 5A DC output (for indoor use only) –100
ď‚· USB 2.0 cable
ď‚· Hard carrying case
 Oponal Go2Nova® 8411 OLED handset with control cable
 Oponal external iPolar (#3339)
 Oponal carbon ber tripod (#8061)
 Oponal counterweight sha P-SGP-CWS and counterweight 3006- ) (# ) (# 05
ONLINE RESOURCES www.iOptron.com ( )
 User’s Manual
 Hand controller and mount rmware upgrades (check online for the latest version)
ď‚· ASCOM drive, Commander, Commander Lite and other computer control
1Contents and design may change from me to me without noce.
2
iOptron Corp. | 1 Merrill Street | Woburn, MA01801USA | (781) 569-0200 | Toll Free (866) 399-4587 | www.iOptron.com
Please hold the telescope when disengaging the DEC Gear Switch. An HAE mount is operated
under unbalanced condions and could be pped o if the tripod is not secured.
1. Remove mount head from package:
2. Set Latude Range: An HAE16C has two latude
range sengs: 0~47° and 43~90°. The default seng
is 0~47° (front latude hole). You may change the
latude range based on your locaon or if an
altazimuth (AA) mode is desired. Slightly loosen
Altude Locking Knob. Use a at head screw driver to
remove the Latude Locking Pin. Adjust the mount so
that the hole on the brass latude eyebolt is aligned
to the high latude posion hole. Insert the Locking
Pin to secure it.
3. Set up tripod: An HAE16C mount uses -a 3/8” 16
threaded hole for aachment. So a camera tripod or
other tripod with a 3/8”-16 mounng post can be
used. Shown here is an iOptron carbon ber tripod
#8061/#8061A.
4. Aach mount head: Thread the mount head onto the
tripod head and secure it.
Level the mount by adjusng the tripod legs Use the .
built-in Bubble Level Indicator on the mount base or
an external leveler for this purpose.
5. Adjust latude: To adjust the latude, slightly loosen
the Altude Locking Knob. Use the Latude
Adjustment Knob to move the mount to the desired
latude by aligning the Latude Mark Line to the
Latude Scale. Tighten the Alt. Locking Knob.
3/8”-16 mounting post
Lat. Scale
Lat. Range
Locking Pin
High Latitude
Lat. Adj.
Knob
Alt. Locking
Knob
3
iOptron Corp. | 1 Merrill Street | Woburn, MA01801USA | (781) 569-0200 | Toll Free (866) 399-4587 | www.iOptron.com
6. Install telescope: An HAE16C mount accepts a Vixen
dovetail mounng plate.
Release the dovetail Saddle Locking Lever and slide
the telescope dove il plate into the saddle with Gear ta
Switch disengaged. Make sure that the arrow sign on
the saddle is poinng forward. Tighten the Saddle
Locking Lever.
The locking levers on an HAE16C mount are ratchet
ones. Pull the lever handle and turn it to the posion
that the lever is parallel to the saddle or points
towards the scope to prevent it interfering with the
DEC unit during mount GOTO and tracking.
7. Balance payload: No RA balance is needed for an
HAE16C mount.
Turn the mount power on. Press number 9 to change
the slew speed to max. Press or button to slew â—„ â–ş
the telescope to one side of the mount. Hold the
telescope and disengage DEC Gear Switch to check
the balance Release the dovetail saddle locking lever .
and move the scope back and forth to adjust the
posion. Tighten the dovetail saddle locking lever and
engage the gear switch aer balancing is completed.
Return the mount to Zero Posion aer balancing
and engage the DEC gear switch.
8. Install counterweight bar and CW: The mount is
designed to operate without a counterweight (CW). If
you want to use an oponal CW, the CW sha
mounng hole is 3/8”-16 threaded. Thread in a CW
shaf ( -SGP-CWS and install a 5 lbs CW ((#3006-t #P )
05) .
9. Connect DC power and handset: Plug in a 12V DC
power supply to the socket on the base. DC12V IN
If you have an oponal Go2Nova® 8411 handset, plug
it into the 6P6C handset port on the mount.
10. Mount control via a SmartPhone/Tablet: The mount
can be controlled by the iOptron Commander Lite
app for inial sengs, as well as slew, GOTO and
tracking.
Turn the mount power on. Check your SmartPhone
WIFI seng and connect to a WIFI device named
HAECser_XXXXXX.
Locking Lever


Product specificaties

Merk: IOptron
Categorie: Statief
Model: HAE16C

Heb je hulp nodig?

Als je hulp nodig hebt met IOptron HAE16C stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Statief IOptron

Handleiding Statief

Nieuwste handleidingen voor Statief