Flyzone DHC-2 Beaver Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Flyzone DHC-2 Beaver (16 pagina's) in de categorie Radiografisch bestuurbaar speelgoed. Deze handleiding was nuttig voor 64 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/16
© 2012 Hobbico®, Inc. All rights reserved. FLZA4020 FLZA4022 Mnl
Length: 38.5 in
[980mm]
Radio: 5-channel
radio system
Motor: 40mm dia.
850kV outrunner,
40A ESC,
12x6 propeller
SPECIFICATIONS
Wingspan: 59.5 in
[1510mm]
Wing
Area:
430 in2
[27.7 dm2]
Weight: 3 3.25 lb
[13601470 g]
Wing
Loading:
1617 oz/ft2
[49 52 g/dm2]
READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT
INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.
WARRANTY
Flyzone guarantees this kit to be free from defects in both
material and workmanship at the date of purchase. This warranty
does not cover any component parts damaged by use or
modification. In no case shall Flyzone’s liability exceed the
original cost of the purchased kit. Further, Flyzone reserves
the right to change or modify this warranty without notice.
In that Flyzone has no control over the final assembly or material
used for final assembly, no liability shall be assumed nor
accepted for any damage resulting from the use by the user of
the final user-assembled product. By the act of using the
user-assembled product, the user accepts all resulting liability.
If the buyer is not prepared to accept the liability associated
with the use of this product, the buyer is advised to return
this kit immediately in new and unused condition to the
place of purchase.
To make a warranty claim send the defective part or item to
Hobby Services at the address below:
Hobby Services
3002 N. Apollo Dr. Suite 1
Champaign IL 61822 USA
Include a letter stating your name, return shipping address, as
much contact information as possible (daytime telephone
number, fax number, e-mail address), a detailed description of
the problem and a photocopy of the purchase receipt. Upon
receipt of the package the problem will be evaluated as quickly
as possible.
INSTRUCTION
MANUAL
2
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Academy of Model Aeronautics . . . . . . . . . . . . . . . . . . 2
SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 2
REQUIRED FOR COMPLETION . . . . . . . . . . . . . . . . . . . . 3
Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
LiPo Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
KIT INSPECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . 3
CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Mount the Landing Gear . . . . . . . . . . . . . . . . . . . . . . . 5
Mount the Floats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Mount the Horizontal and Vertical Stabilizer . . . . . . . . 6
Install the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Hook Up the Rudder and Elevator . . . . . . . . . . . . . . . . 8
Mount the Wings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Hook Up the Flaps and Ailerons . . . . . . . . . . . . . . . . 11
FINAL FLIGHT PREPARATION . . . . . . . . . . . . . . . . . . . 12
Check the Control Throws . . . . . . . . . . . . . . . . . . . . . 12
Check the C.G.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
MOTOR SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . 14
MOTOR / ESC OPERATION . . . . . . . . . . . . . . . . . . . . . . 15
FLYING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
REPAIRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
TABLE OF CONTENTS
INTRODUCTION
Thank you for purchasing the Flyzone 1/10
th
-scale de Havilland
DHC-2 Beaver RTF/Tx-R. For anybody who enjoys ying oat
planes or who aspires to do so for the fi rst time, the Flyzone
Beaver is the perfect choice because it maneuvers and fl ies
off the water so well—you virtually can’t mess up a takeoff or
landing unless you try! Of course, the Beaver is almost just
as much at home on dry land as it is in the water. And with
the aps extended you can set your Beaver down on water
or on land as light as a feather.
For the latest technical updates or manual corrections to the
Beaver, visit the Flyzone site at www.fl yzoneplanes.com. Open
the “Airplanes” link, then select the Beaver ARF. If there is
new technical information or changes to this model a “tech
notice box will appear in the upper left corner of the page.
Academy of Model Aeronautics
If you are not already a member of the AMA, please join! The
AMA is the governing body of model aviation and membership
provides liability insurance coverage, protects modelers’ rights
and interests and is required to fl y at most R/C sites.
Academy of Model Aeronautics
5151 East Memorial Drive
Muncie, IN 47302-9252
Tele. (800) 435-9262
Fax (765) 741-0057
Or via the Internet at: http://www.modelaircraft.org
IMPORTANT!!! Two of the most important things you can
do to preserve the radio controlled aircraft hobby are to avoid
ying near full-scale aircraft and avoid ying near or over
groups of people.
SAFETY PRECAUTIONS
PROTECT YOUR MODEL, YOURSELF AND OTHERS...
FOLLOW THESE IMPORTANT SAFETY PRECAUTIONS
1. Your de Havilland Beaver should not be considered a toy, but
rather a sophisticated, working model that functions very much
like a full-size airplane. Because of its performance capabilities,
the Beaver, if not assembled and operated correctly, could
possibly cause injury to yourself or spectators and damage
to property.
2. You must assemble the Beaver according to the instructions.
Do not alter or modify the model, as doing so may result in an
unsafe or un yable model. In a few cases the instructions may
differ slightly from the photos. In those instances the written
instructions should be considered as correct.
3. You must use an R/C radio system that is in good condition.
All components must be correctly installed so that the model
operates correctly on the ground and in the air. You must
check the operation of the model and all components before
every ight.
4. If you are not an experienced pilot or have not own this type
of model before, we recommend that you get the assistance
of an experienced pilot in your R/C club for your rst ights.
If you’re not a member of a club, your local hobby shop has
information about clubs in your area whose membership
includes experienced pilots.
5. While this kit has been ight tested to exceed normal
use, if the plane will be used for extremely high stress fl ying,
such as racing, or if a motor or battery larger than ones in
the recommended range is used, the modeler is responsible
for taking steps to reinforce the high stress points and/or
substituting hardware more suitable for the increased stress.
3
We, as the kit manufacturer, provide you with a top quality,
thoroughly tested kit and instructions, but ultimately the
quality and yability of your nished model depends on how
you build it; therefore, we cannot in any way guarantee the
performance of your completed model, and no representations
are expressed or implied as to the performance or safety of
your completed model.
Remember: Take your time and follow the instructions to
end up with a well-built model.
REQUIRED FOR COMPLETION
Other than a #1 and #2 Phillips screwdriver and a few drops
of non-permanent threadlocker (GPMR6060), no adhesives
or anything extraordinary is required to assemble the Beaver.
The RTF is fully equipped with a complete radio control
system, LiPo battery and charger, so no other accessories
are required, but the following items are required to complete
the Tx-R edition:
Transmitter
The Tx-R includes the Tactic™ TR624 6-Channel 2.4GHz
receiver, so you’ll need either a Tactic TX600 6-channel 2.4GHz
transmitter, or any other 5-channel (or more) transmitter
compatible with the Tactic AnyLink™ 2.4GHz radio adapter*.
Using the AnyLink allows any compatible transmitter to work
with the Tactic receiver.
TX600 6-channel transmitter (TACJ2600)
AnyLink radio adapter* (TACJ2000)
*In addition to the AnyLink radio adapter, some AnyLink-
compatible transmitters may also require additional adapter
cables. Visit Tx-Ready.com to see the compatibility AnyLink
chart or contact Product Support at the contact information
on this page.
LiPo Battery
The RTF edition of the Beaver includes a Flyzone 3S (11.1V)
1800mAh 20C LiPo battery and the same is recommended for
the Tx-R, but a 2100mAh battery is also an option for slightly
longer fl ight times (more about fl ying time on page 15).
Flyzone 3S (11.1V) 1800mAh 20C LiPo battery
(HCAA6430)
Flyzone 3S (11.1V) 2100mAh 20C LiPo battery
(HCAA6387)
Spare batteries may also be purchased and charged at home
ahead of time, eliminating the wait between ights for batteries
to charge at the fi eld.
NOTE: The Flyzone batteries suggested are equipped with
a SuperTigre
®
battery connector that t the connector on
the ESC. If using a different LiPo battery that has a Deans®
connector, a SuperTigre-to-Deans adapter (SUPM0040) will
be required, or the battery connector on the ESC may be
replaced with a Deans Ultra Plug® male connector which will
require soldering (but is a simple task for those so equipped).
Charger
The RTF comes equipped with a Great Planes 3S LiPo
balancing Smart Charger, but the Tx-R requires a charger to
be purchased separately. The Smart Charger is a safe way to
charge your LiPo battery, but it’s very basic and just enough
to get you started. The Smart Charger charges at a rate of .8
Amps, so it will take at least one-and-a-half hours or more to
charge your battery. For those who have the RTF and wish
to upgrade their charger, or those with the Tx-R who must
purchase a charger anyway, the Duratrax® Onyx235 AC/
DC Advanced Peak Charger (DTXP4235) is recommended.
The Onyx is perfect for 3S batteries used with the Beaver
and may be powered either by an external DC power source
(such as a 12V battery), or a 110V AC outlet. The Onyx also
has an adjustable charge rate to charge your batteries in as
little as a half-hour or less (depending on the condition of your
batteries and the manufacturer’s specifi ed charge rate). The
Onyx can also charge larger batteries and batteries other than
LiPos, so it is a versatile charger you can grow into. Finally, the
235 features an LCD digital display screen, so you can see
how much capacity it took to recharge the battery (required
for monitoring the condition of your batteries and calculating
how long you can fl y).
NOTE: For use with the Onyx 235, LiPo batteries that come
with a SuperTigre connector (such as the Flyzone batteries
recommended) require a banana plugs-to-SuperTiger charge
lead (SUPM0070). And batteries that come with a Deans Ultra
Plug connector require a Charge Lead with banana plugs/
Deans Ultra Plug Male charge lead (GPMM3148).
KIT INSPECTION
Before assembly, take an inventory of this kit to make sure
it is complete, and inspect the parts to make sure they are
of acceptable quality. If any parts are missing or are not of
acceptable quality, or if you need assistance with assembly,
contact Product Support. When reporting defective or missing
parts, use the part names exactly as they are written in the
Contents list.
Flyzone Product Support Ph: (217) 398-8970 ext. 5
3002 N Apollo Drive Suite 1 Fax: (217) 398-7721
Champaign, IL 61822
E-mail: airsupport@ yzoneplanes.com
ORDERING REPLACEMENT PARTS
Replacement parts for the Flyzone de Havilland Beaver RTF/
Tx-R are available using the order numbers in the Replacement
Parts List that follows. The fastest, most economical service
can be provided by your hobby dealer or mail-order company.
To locate a hobby dealer, visit the Flyzone web site at www.
yzoneplanes.com. Click on the Storefront icon at the top
of the page to load the Flyzone Dealer Locator. Follow the
instructions provided on the page to locate a U.S., Canadian or
International dealer.


Product specificaties

Merk: Flyzone
Categorie: Radiografisch bestuurbaar speelgoed
Model: DHC-2 Beaver
Kleur van het product: Red, Silver
Gewicht: 1470 g
Capaciteit van de accu/batterij: 1800 mAh
Lengte: 980 mm
Constructietype: Montagekit
Aantal kanalen: 4 kanalen
Type product: Watervliegtuig
Type motor: Borstelloos
Motorafmeting: 40mm
Reproductie: Ja
Spanwijdte: 1510 mm
Elektronische toerentalregeling (ESC): Ja
Type elektronische toerentalregeling (ESC): Geborsteld
Vleugeloppervlak: 2770 cm²
Aanbevolen batterij: 11.1V 1800mAh LiPo

Heb je hulp nodig?

Als je hulp nodig hebt met Flyzone DHC-2 Beaver stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Radiografisch bestuurbaar speelgoed Flyzone

Handleiding Radiografisch bestuurbaar speelgoed

Nieuwste handleidingen voor Radiografisch bestuurbaar speelgoed