FireAngel HW1-R Handleiding

FireAngel Rookmelder HW1-R

Lees hieronder de 📖 handleiding in het Nederlandse voor FireAngel HW1-R (1 pagina's) in de categorie Rookmelder. Deze handleiding was nuttig voor 41 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

300mm

1. POSITIONING

Your heat alarm is suitable for the kitchen,

garage and loft.

Heat alarms should be sited at least 300mm

from light fittings and walls. Ideally as central

as possible in the room. Do not install heat

alarms on a wall.

Install your heat alarm at a distance no greater

than 5.3m from the farthest wall, no greater

than 5.3m from a door to any room in which a

fire might start and no greater than 5.3m from

the next heat or smoke alarm.

If there is fluorescent lighting, heat alarms

should be installed at least 1500mm from

these fittings and wiring. Keep any wiring at

least 1000mm from fluorescent lighting.

Do not use circuits containing fluorescent light

fittings or dimmer switches.

If there is fluorescent lighting, heat alarms

should be installed at least 1500mm from

these fittings and wiring. Keep any wiring at

least 1000mm from fluorescent lighting.

Do not use circuits containing fluorescent light

fittings or dimmer switches.

Locations of alarms must be compliant

with either BS 5839: Part 6 or relevant

Building Regulations if in any doubt.

2. INSTALLATION

TROUBLESHOOTING GUIDE WARRANTY AND DISPOSAL

HW1 MAINS POWERED HEAT ALARM

WITH 9V BATTERY BACK-UP

USER MANUAL

IMPORTANT: The circuit used to Power the alarm must be a 24 hour voltage circuit that cannot be turned off by a switch.

In accordance with BS 5839: Part 6, we recommend: For mains powered alarms, each with an integral standby supply, the mains

electricity supply should take the form of either a) an independent circuit at the dwelling’s main circuit board, in which case no

other electrical equipment should be connected to this circuit (other than a dedicated monitoring device installed to indicate

failure of the mains electricity supply to the alarms); or b) a separately electrically protected, regularly used local lighting circuit.

Check with local building and ﬁre regulations for your property, to ensure compliance.

Ensure dust cover is removed before operation.

The red LED on the front of the alarm should ﬂash once every 32 seconds (approx.) to show that the alarm sensor is actively

monitoring for heat. When the test button is pressed, the alarm will ﬂash once every 8 seconds for 8 minutes.

FireAngel Safety Technology Limited warrants to the original purchaser that its enclosed smoke alarm be free from defects in materials and

workmanship under normal residential use and service for a period of 5 (ﬁve) years from the date of purchase (not including the replaceable

battery). Provided product is sent back to FireAngel Safety Technology Limited with proof and date of purchase, FireAngel Safety Technology

Limited hereby warrants that during the 5 (ﬁve) year period commencing from the date of purchase FireAngel Safety Technology Limited, at its

discretion, agrees to replace the unit free of charge. The warranty on any replacement HW1 alarm, will last for the remainder of the period of the

original warranty in respect of the alarm originally purchased – that is from the date of original purchase and not from the date of receipt of the

replacement product. FireAngel Safety Technology Limited reserves the right to offer an alternative product similar to that being replaced if the

original model is no longer available or in stock. This warranty applies to the original retail purchaser from the date of original retail purchase and

is not transferable. Proof of purchase is required.

This warranty does not cover damage resulting from accident, misuse, disassembly, abuse or lack of reasonable care of the product, or

applications not in accordance with the user manual. It does not cover events and conditions outside of FireAngel Safety Technology Limited’s

control, such as Acts of God (ﬁre, severe weather etc.). It does not apply to retail stores, service centres or any distributors or agents. FireAngel

Safety Technology Limited will not recognise any changes to this warranty by third parties.

FireAngel Safety Technology Limited shall not be liable for any incidental or consequential damages caused by the breach of any expressed or

implied warranty. Except to the extent prohibited by applicable law, any implied warranty of merchantability or ﬁtness for a particular purpose is

limited in duration for 5 (ﬁve) years.

This warranty does not affect your statutory rights. Except for death or personal injury, FireAngel Safety Technology Limited shall not be liable

for any loss of use, damage, cost or expense relating to this product or for any indirect, or consequential loss, damages or costs incurred by

you or any other user of this product.

DISPOSAL

Waste electrical products should not be disposed of with your other household waste. The alarm is ideally suited for disposal within the

waste electronic and electrical equipment (WEEE) recycling scheme.

Please recycle where facilities exist. Check with your local authority, retailer or contact our Technical Support team for recycling/disposal

advice as regional variations apply.

Once the batteries are removed, the low battery warning chirp will stop. The batteries should always be removed before disposal.

Do not attempt to open. Do not burn.

6. LOW BATTERY WARNING

Your alarm requires 1 x 9V (PP3) battery. Under normal use, the battery should last approximately one year.

Use of a battery other than those recommended here may have a detrimental effect on the alarm performance:

Duracell MN1604, Gold Peak: GP1604S, Raymax: 6F22.

6a When the alarm battery is low, the alarm will ‘chirp’

and the LED will ﬂash every 32 seconds.

6c Twist alarm

anti-clockwise to

remove from base

plate and disconnect

power adapter.

6d Replace the batteries and re-install.

(See 'Installation') 6e Always test the alarm after replacing

the batteries.

Switch off electricity supply.

4a For multiple alarm installations use a ‘three core and earth’ style cable between all the alarms to be interconnected.

Connect the 3rd core of the cable (‘Interconnect’ cable), to the white wire from the heat alarm’s power connector (see Installation).

4b Test each alarm and ensure every connected alarm

sounds within 10 seconds.

Up to 12 FireAngel mains smoke (SW1), heat (HW1) or carbon monoxide alarms (CW1) can be interconnected on

a single network.

4. OPTIONAL INTERCONNECTING FEATURE

On an interconnected network, only the alarm that senses the ﬁre will sound and ﬂash its LED. Other connected alarms will sound a

warning but will not ﬂash their LED. Do not connect more than 11 other devices.

IMPORTANT: The interconnect wire (minimum 0.75 mm2 cable) must be treated as Live, it should be insulated and sheathed.

Mains 230V AC

Power Supply

WIRING KEY

= Live

= Interconnect

= Neutral

= Earth

To other alarms

if ﬁtted

Press and hold the test button for 5 seconds.

The alarm will sound.

Switch off electricity supply.

Remove the baseplate by twisting the alarm anti-clockwise.

Connect the house wiring to the power connector provided.

Ensure a permanent connection is made in a suitable junction

box (not provided).

No connection should

be made to the mains

electricity supply

earth terminal.

Terminate house

wiring earth in spare

connector.

Fit the base to ceiling

using the screws

provided. Feed the

wiring through the

hole in the base plate

and connect the

power adapter to

the alarm.

2a Unwrap battery. Insert battery into battery compartment

(match ‘+’ to ‘+’). Remove dust cover. Press and hold the

test button for 5 seconds. The alarm will sound.

3a Press and hold the

button for

5 seconds.

In a known false alarm, the alarm can be silenced temporarily.

3. SILENCE FEATURE

The alarm will silence for

10 minutes.

Push and twist the alarm clockwise onto the base plate.

Turn the electricity supply back on and check that the

green LED is on.

5. MAINTENANCE

5a Test the alarm every month.

Press the test button for 5 seconds.

The alarm will sound.

5b Vacuum your alarm

every 3 months.

5c Do not use cleaners or solvents. 5d Do not paint the alarm.

Replace the alarm every

10 years.

5e Do not use any other test method except

the process described in this manual.

2e Remove locking plug from baseplate.

Insert into hole between base plate and alarm

OPTIONAL LOCKING FEATURE

Brown (live)

Blue (neutral)

Black or grey (interlink)

Earth

White

Baseplate

Brown

Blue

• Check the location of your heat alarm.

• Clean the heat alarm.

• Check the location of your heat alarm.

• Clean the heat alarm.

• Check that your alarm is connected to the power supply and that the

battery is installed correctly.

• If testing after installation, allow a few seconds for the alarm to settle.

• Push and hold the centre of the test button ﬁrmly for 5 seconds.

• Check that the alarm is properly connected to the mains power.

• Check the location of your heat alarm.

• Check that your heat alarm is deﬁnitely the source of the chirping; make

sure the noise isn’t coming from another alarm.

• If the alarm ‘chirps’ every 32 seconds and the red LED ﬂashes at the

same time - replace the battery.

• If the alarm ‘chirps’ every 32 seconds without a red LED ﬂash, a fault is

indicated - contact Techincal Support.

• Check that your heat alarm is connected to the power

supply and that the battery is correctly installed.

If the green LED does not light when the alarm

is connected to power:

If your heat alarm does not sound during

testing:

If your heat alarm activates when no smoke is

visible:

If your heat alarm sounds unusual or ‘chirps’

intermittently:

If you experience frequent unwanted alarms:

220-240 V AC 50-60 Hz mains powered heat alarm. 9V battery back-up.

WARNING: Wiring should be installed by a qualiﬁed electrician in accordance with local building

standards. The wiring must conform to current regulations for electrical installations. Check with local

building and ﬁre regulations for your property, to ensure compliance.

For the best protection, heat alarms should always be installed as part of a complete ﬁre protection

system that includes smoke alarms.

Class A2 detection. This heat alarm will sound a warning when the ambient temperature in a room is

between 54°C and 70°C.

This heat alarm is not intended for any non-residential, commercial or industrial application, nor for any

other purpose than described above.

WARNING: Experience has shown that children may not be woken by ﬁre alarm tones. It is important

that children are never left alone in a house. Families should have a ﬁre escape plan that is rehearsed, so

that everyone knows how to escape when ﬁre occurs. The immediate priority when ﬁre occurs is to

ensure that any sleeping children are woken from sleep and are immediately taken to a place of safety

outside the property, along with all other occupants. The ﬁre and rescue service should always be called

without delay, no matter how small the ﬁre.

GN5091R6

Your alarm features ‘Silence’ technology. In the event of a known false alarm you can temporarily silence it by pressing the

button. After 10 minutes your alarm will automatically sound 2 chirps and return to full sensitivity.

The red LED on the front of the alarm will ﬂash once every 8 seconds to show that it is in Silence mode.

The alarm will sound continuously and the red LED will ﬂash every second when the alarm senses dangerous heat levels. NEVER

IGNORE ANY ALARM. If an alarm is sounding, it is warning you of a potentially hazardous situation. Do not ignore it. Ignoring the

alarm may result in injury or death. If your heat alarm activates and you are not absolutely certain of the source of the problem,

get everyone out of the house immediately.

Junction box

(not provided)

Power connector

To enable removal of the alarm,

withdraw the locking plug with a

pair of pliers.

BS 5446-2: 2003

Licence No: KM694292

Vanguard Centre, Coventry CV4 7EZ, UK

www.ﬁreangeltech.com

Technical Support

Online: www.ﬁreangeltech.com/support

E-mail: technicalsupport@ﬁreangeltech.com

Phone: 0330 094 5830

Fire & Rescue Customers: 0800 141 2561

Note: This user manual is also available in large text and other formats. Please email: technicalsupport@ﬁreangeltech.com or call 0330 094 5830 for further information.