Extron MVC 121 Plus Handleiding

Extron Mengpaneel MVC 121 Plus

Lees hieronder de 📖 handleiding in het Nederlandse voor Extron MVC 121 Plus (2 pagina's) in de categorie Mengpaneel. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

IMPORTANT:

Go to www.extron.com for the

complete user guide, installation

instructions, and specifications.

MVC 121 Plus • Setup Guide

The Extron MVC 121 Plus is an audio mixer and volume controller that will mix up to two mono mic/line inputs (balanced/

unbalanced) with one stereo line level input (balanced/unbalanced). All audio input signals are converted from analog to digital

prior to processing or routing. Each mic/line input and the line level input have their own gain control adjustment screws. The

mixed variable output also features a volume control knob on the front panel.

NOTE: For full installation, configuration, and operation details, see the , available at MVC 121 Plus User Guide

www.extron.com.

Rear Panel Features and Connections

a 12 VDC power connector f Fixed output connector

b Mic 1 and 2 Phantom power LED g RS-232 connector

c Mic/Line input connectors (1 – 2) h Digital input connector

d Line input connector (3) i Reset button

e Variable output connector

Installing the MVC 121 Plus

1. Disconnect power from all equipment.

2. (Optional) Mount the unit to a rack or furniture.

3. Connect the audio inputs.

• Connect up to two balanced or unbalanced mono mic/line level input devices to

connector above (see the 6-pole wiring diagram on the right). Alternatively, c

two 3-pole connectors may be used.

• A balanced or unbalanced stereo line level input may be connected to above (see the 5-pole wiring diagram below). d

Balanced audio

Tip

Ring

Tip

Ring

L R

Slee

ves

Unbalanced audio

Tip

Sleeve

Tip

L R

Do not tin the wires!

4. Connect the audio output.

• For variable balanced or unbalanced stereo output controlled

by the front panel knob of the MVC 121 Plus, connect an

amplier to the Variable connector e, above (see the wiring

diagram on the right).

• For xed stereo output, connect an output device to Fixed

connector f (see the wiring diagram above).

5. Connect a control device. Connect a host device, such as a computer, to

one of the following MVC ports to congure and control the MVC 121 plus via

Simple Instruction Set (SIS™) commands.

• RS-232 port (rear panel) — Connect a host device to the Tx, Rx, and

_ (ground) pins of this 6-pole captive screw connector (g). The default

baud rate for this port is 38400 baud, 1 stop bit, no parity, 8 data bits, and

no ow control (see the wiring diagram on the right).

• Conﬁg port (front panel) — See Front Panel Features on the next page.

6. Digital input connector. Up to three congurable input ports (see h on the

rear panel diagram above) allow connection to various devices including motion

detectors, alarms, buttons, photo (light) sensors, and temperature sensors. This

connector shares a common ground with the RS-232 connector (see the wiring

diagram on the right).

Both the RS-232 and digital input connectors may be used simultaneously by

using a 6-pin captive screw connector with two wires sharing the ground connector

(see the diagram on the right).

1 2MIC/LINE

Balanced MIC

Unbalanced MI

Jumper

Unbalanced Stereo Output

Tip

NO GROUND HERE.

Slee

ve(s)

Tip

NO GROUND HERE.

Balanced Stereo Output

Tip

Ring

Sleeve(s)

Tip

Ring

L R

Left

Right

Left

Right

Do not tin the wires!

Transmit (Tx)

Receive (Rx)

Ground (Gnd,

)

RS-232

21Tx Rx

DIGI IN

Do not tin the wires!

RS-232

21Tx Rx

DIGI IN

+48V

MIC

1 2MIC/LINE

LINE 3L R RL

POWER

0.4A MAX

12V

RS-232

VARIABLE

FIXEDL R DIGI IN

MVC 121 Plus

Tx Rx 1 2 3

INPUTS OUTPUTS

RESET

123

4 5

RS-232 DIGI IN

Tx Rx 1 2 3

68-1937-50 Rev. B

10 13

Extron USA Headquarters

+1.800.633.9876 (Inside USA/Canada Only)

Extron USA - West: +1.714.491.1500 FAX: +1.714.491.1517

+1.919.850.1000 FAX: +1.919.850.1001Extron USA - East:

MVC 121 Plus • Setup Guide (continued)

7. Reset button. The recessed reset button (see i on the rear panel diagram

on the previous page) is used to access various modes of resets. The green

power LED on the front panel indicates the reset mode that was used.

8. Connect power to the MVC by connecting the included 12 VDC external

power supply to the rear panel power connector (see a on the rear panel

diagram). The wiring diagram is shown on the right.

9. Install the software. Conguration and control is done via both hardware

encoders and software. The control software, DSP Congurator, is available

at www.extron.com Software and Manual Download from the Website (see

below). The control software help le contains operation descriptions.

Front Panel Features (see the front panel diagram at right)

a — This power indicator lights green when the MVC 121 Plus Power/Reset LED

is operational. The LED also blinks per mode reset.

b — Connect a PC to the USB Mini-B connector for Conﬁguration (Conﬁg) port

conguring the MVC using the DSP Congurator Software. The MVC 121 Plus

USB driver must be installed prior to using this port.

c — Rotating the encoder screw clockwise increases the gain setting. Rotating the encoder screw Mic 1 input gain control

counterclockwise decreases the gain. This adjustment controls the single gain point in the mix matrix that mixes mono mic 1

levels to the stereo output bus.

d — Rotating the encoder screw clockwise increases the gain setting. Rotating the encoder screw Mic 2 input gain control

counterclockwise decreases the gain setting. This adjustment controls the single gain point in the mix matrix that mixes

mono mic 2 levels to the stereo output bus.

e — Rotating the encoder screw clockwise increases the gain setting. Rotating the encoder Line level input 3 gain control

screw counterclockwise decreases the gain setting. This adjustment controls the single gain point in the mix matrix that

mixes line level input 3 to the stereo output bus.

f — As the mix-point gain or output volume increases or decreases, the LED indicator bar lights LED ladder indicator bar

from the bottom to the top to indicate the current mix-point or volume level. As the volume is increased or decreased within

a volume range, the top lit LED ashes once. If the knob is turned past maximum volume, all 8 LEDs ash for as long as the

knob continues to be turned. After 3 seconds of inactivity, the knob controls the variable volume output.

g Volume level adjust knob — Rotating the adjustment knob clockwise increases the output volume. Rotating the knob

counterclockwise decreases the volume.

Software and Manual Download from the Website

1. Using any internet browser, go to www.extron.com.

2. From the Extron home page, select the from the drop-down menu.

3. Select the tab on the MVC 121 Plus product page.

4. Select the User Guide from the list of available documentation and click on it to either view or download it to the hard drive

for future reference.

5. To download the control software, on the tab select .

6. The link navigates to the selected software download page. Fill out the form, then download the software to the hard drive.

NOTE: On the first installation of DSP Configurator, the USB driver loads automatically. Follow the on-screen instructions.

Once the USB driver has loaded, DSP Configurator continues to load.

By default, the program installs in and an icon is placed on the desktop.

SECTION A–A

Power Supply

Output Cord

Ridges

Smooth

Ridges

Smooth

2-P

ole Orange

Captive Scre

Connector

(12V)

Tie Wrap

3/16”

(5 mm) Max.

VOLUME

CONFIG

MIX

MIC MIC LINE

321

MIXER/VOLUME CONTROLLER

MVC 121 Plus

21 3 4 5 6 7

Product specificaties

Merk:	Extron
Categorie:	Mengpaneel
Model:	MVC 121 Plus
Gewicht:	300 g
Breedte:	109 mm
Diepte:	76 mm
Hoogte:	43 mm
Gewicht verpakking:	840 g
Breedte verpakking:	257 mm
Diepte verpakking:	189 mm
Hoogte verpakking:	70 mm
Rack-montage:	Ja
Frequentiebereik:	20 - 20000 Hz
Crosstalk (1kHz):	-90 dB
Aantal kanalen:	- kanalen
Totale harmonische vervorming (THD):	0.02 procent
Rackcapaciteit:	1U
AC-ingangsspanning:	100-240 V
AC-ingangsfrequentie:	50 - 60 Hz
Stroomverbruik (typisch):	4.8 W
Digitaal geluid verwerken:	24 Bit
Line Signal-to-Noise Ratio (SNR):	100 dB