Emko ESM-3722 Handleiding

Emko Thermostaat ESM-3722

Lees hieronder de 📖 handleiding in het Nederlandse voor Emko ESM-3722 (2 pagina's) in de categorie Thermostaat. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
2.2PanelCut-Out
ESM- 77x35DINSizeHatcherController3722
InstructionManual.ENGESM-372201V0402/15
2.GeneralDescription
2.1FrontViewandDimensionsofESM-3722HatcherController
All order information of ESM-3722 Hatcher Controller are given on the table at above. User may form
appropriate device configuration from information and codes that at the table and convert it to the
ordering codes.Firstly, supply voltage then other specifications must be determined. Please fill the order
code blanks according to your needs. Please contact us, if your needs are out of the standards.
10.OtherInformations
WhenSET buttonispressedfor3
seconds,“P”ledturn.Ifprogramming
modeenteringpasswordisdifferent
from0,programmingmodeentering
screenwillbeobserved.
MainOperationScreen
ProgrammingScreen
Changethevaluewithincrement
anddecrementbuttons.
Press SET button for accessing to the
parameter value. Press increment
button for accessing to the next
parameter, press decrement button for
accessing to the previous parameter.
Presssetbuttonforsavingthe
parameter.
Press increment button for accessing to
the next parameter, press decrement
button for accessing to the previous
parameter.
ProgrammingMode
EnteringScreen
PressSET buttonfor
accessingtothe
passwordentering
PasswordEnteringScreen
Enterprogrammingmodeaccessing
passwordwithincrementand
decrementbuttons.
Note2: If programming mode accessing password is 0, only three parameters are accessible, and the
parameter values can be changed.
PressSET/OKbuttonfor
enteringthepassword.
Note1: Ifprogramming
modeaccessingpassword
is0, TemperatureUnit
screen isobserved
insteadofprogramming
screen
If no operation is performed in programming mode for 20 seconds, device turns to main
operation screen automatically.
i
DecimalSeparatorEnabling
SelectionScreen
5.5EnteringToTheProgrammingMode,ChangingandSavingParameter
14
13
3sec.
76mm/3inch
34,5mm/1.36inch
15
While button protection parameter value is 0,1,2 or
4 in main operation screen if engine button is pressed,
manual engine start will be active.When the button is
released the engine start will be passive and engine stops.
6. ManualStartofEggTrayRotatorOperationwithEngineButton
Note-1: If input type is selected PTC or NTC (B = 2, 3), Temperature sensor is given with the
device.For this reason, if input type is selected as PTC,sensor type (V = 0,1 or 2) or if input type is
selected as NTC, sensor type (V = 0, 3 or 4) must be declared in ordering information.
8.Specifications
PasswordEnteringScreen
TemperatureUnitSelection
ParameterValue
TemperatureUnitSelection
ParameterValue
8.Specifications
c
1.2.GeneralSpecifications
1.Preface
ESM3722-HT seriesHatchercontrollersaredesignedforcontrollinghatcherprocess.Device
canbeusedeasilywithPIDorOn-Offcontrolformandmanualstartofeggtrayrotatorproperties.
ESM-3722
PowerSupply
Input
Output
Output
Output
2
Humidification
EggTrayRotatorOutput
Alarm
1.1EnvironmentalRatings
-4DigitsforTemperatureDisplay
-4DigitsforHumidityDisplay
-TemperatureSensorInput
NTC,PTC,PT-100,0/2..10V,0/4..20mA orProNemMiniPMI-P
(Mustbedeterminedinorder.)
-HumiditySensorInput
0/2..10V,0/4..20mA orProNemMiniPMI-P
(Mustbedeterminedinorder.)
-4Output
HeatingControlOutput
EggtrayrotatorOutput
HumidificationControlOutput
AlarmControlOutput
-RelayorSSROutputs(Mustbedeterminedinorder.)
-SelectableTemparatureControl(PIDorON/OFF)
- Auto-TunePID
-Setvalueboundaries
-ManualStartoftrayrotatorfromfrontpanel
- Alarmparametreters
- Adjustableinternalbuzzeraccordingtothealarmsituations
-Passwordprotectionforprogrammingmode,
ESM- 77x35DINSize3722
DigitalHatcherController
3 416
MountingClamp
PanelSurface
(maximumthickness15mm/0.59inch)
Frontpanel
IP65Protection
65mm/2.56inch
6mm/0.24inch
110mm/4.33inch(min)
71mm/2.79inch
29mm/1.14inch
50mm/1.97inch(min)
Maximum15mm/0.59inch
230V ( %15)50/60HzV±
OptionalSupply
Voltage
-30V Z
115V ( %15)50/60Hz
24V ( %15)50/60Hz
24V ( %15)50/60Hz
10
±
±
±
V
V
W
Standard
DeviceType
Housing&Mounting
ProtectionClas
Weight
EnviromentalRatings
Storage/OperatingTemperature
Storage/OperatingHumidity
Installation
OvervoltageCategory
PollutionDegree
OperatingConditions
SupplyVoltageandPower
TemperatureSensorInput
:HatcherController
:76mmx34.5mmx71mmPlastichousingforpanel
Panelcutoutis71x29mm.
:Ip65atfront,Ip20atrear.
: Approximately0.2Kg
:Standart,indooratanaltitudeoflessthan2000meterswith
nonecondensinghumidity.
:-40 Cto+80 C/-30 Cto+80 C
:90%max.(Nonecondensing)
:Fixedinstallation
:II.
:II,officeorworkplace,noneconductivepollution
:Continuous
:
:115
:24
:24
:10-30
:NTC,PTC,PT-100,0/2..10V 0/4..20mA or
ProNemMiniPMI-P
o o o o
Z Z,
230V ( %15)50/60Hz-1.5VA
V ( %15)50/60Hz-1.5VA
V ( %15)50/60Hz-1.5VA
V ( %15)50/60Hz-1.5VA
V 1.5WZ
V
V
V
W
±
±
±
±
Output Heating
YourTechnologyPartner
www.emkoelektronik.com.tr
Thankyouverymuchforyourpreferenceto
useEmkoElektronikproducts,pleasevisitour
webpagetodownloaddetailedusermanual.
OperatingTemperature:
Max.OperatingHumidity:
Altitude :
0to50°C
90%Rh(non-condensing)
Upto2000m.
Forbidden Conditions:
Corrosive atmosphere
Explosive atmosphere
Home applications (The unit is only for industrial applications)
A visual inspection of this product for possible damage occurred during shipment is recommended
before installation.
It is your responsibility to ensure that qualified mechanical and electrical technicians install this product.
If there is danger of serious accident resulting from a failure or defect in this unit, power off the system
and separate the electrical connection of the device from the system.
The unit is normally supplied without a power supply switch or a fuse. Use power switch and fuse as
required.
Be sure to use the rated power supply voltage to protect the unit against damage and to prevent failure
Keep the power off until all of the wiring is completed so that electric shock and trouble with the unit can
be prevented.
Never attempt to disassemble, modify or repair this unit. Tampering with the unit may results in
malfunction, electric shock or fire.
Do not use the unit in combustible or explosive gaseous atmospheres.
During putting equipment in hole on the metal panel while mechanical installation some metal burrs can
cause injury on hands, you must be careful.
Montage of the product on a system must be done with it’s fixing clamps. Do not do the montage of the
device with inappropriate fixing clamp. Be sure that device will not fall while doing the montage.
It is your responsibility if this equipment is used in a manner not specified in this instruction manual.
EMKO Elektronik warrants that the equipment delivered is free from defects in material and
workmanship. This warranty is provided for a period of two years. The warranty period starts from the
delivery date. This warranty is in force if duty and responsibilities which are determined in warranty
document and instruction manual performs by the customer completely.
Repairs should only be performed by trained and specialized personnel. Cut power to the device before
accessing internal parts.
Do not clean the case with hydrocarbon-based solvents (Petrol, Trichlorethylene etc.). Use of these
solvents can reduce the mechanical reliability of the device. Use a cloth dampened in ethyl alcohol or
water to clean the external plastic case.
1.3Installation
1.4Warranty
1.5Maintenance
1.6ManufacturerCompany
ManufacturerInformation:
Repairandmaintenanceserviceinformation:
EmkoElektronikSanayive Ticaret A.Þ.
DemirtaþOrganizeSanayiBölgesiKaranfilSk.No:616369BURSA/TURKEY
Phone:+902242611900
Fax:+902242611912
EmkoElektronikSanayive Ticaret A.Þ.
DemirtaþOrganizeSanayiBölgesiKaranfilSk.No:616369BURSA/TURKEY
Phone:+902242611900
Fax:+902242611912
TemperatureSensor
Input
HumiditySensorInput
0/2..10V,0/4..20mA or
ProNemMiniPMI-P
5.2 AlarmOutputGraphicsofESM-3722HT
i
Process High Alarm
ON
OFF
Alarm
Output
Process Value
Process Low Alarm
ON
OFF
Alarm
Output
ProcessValue
Deviation Band Alarm
ON
OFF
Alarm
Output
(- AlarmSet)
=Process Set Value (Temperature or Humidity)
Deviation Range Alarm
ON
OFF
Alarm
Output
ProcessValue
AlarmSet AlarmSet
(+AlarmSet)
(- AlarmSet) (+AlarmSet)
ProcessValue
5.3EggTrayRotatorOperationGraphicsofESM-3722HT
Egg Tray Rotator
Output Led
Egg Tray Rotator
Output
ü
1- Screen Blinking Temperature Sensor failure . Sensor connection is wrong or there is no sensor
connection. While this message shown on this display,if buzzer function selection is 3, 5, 7 or 8
internal buzzer starts to operate.
5.4 FailureMessagesinESM3722HatcherController
2 Screen Blinking H Sensor failure . Sensor connection is wrong or there is no sensor
connection. While this message shown on this display,if buzzer function selection is 4, 6,7 or 8
internal buzzer starts to operate.
- umidity
NTCinputtype
PTCinputtype
Termoresistanceinputtype
Humidityinputtype
Accuracy
SensorBreakProtection
ControlForm
RelayOutputs
OptionalSSRDriverOutput
TemperatureDisplay
HumidityDisplay
LEDDisplays
InternalBuzzer
Upprovals
:NTC(10k @25°C)
:PTC(1000 @25°C)
:PT-100IEC751(ITS90)
:0/2..10V 0/4..20mA MiniPMI-P
:±1%offullscale
:Upscale
:PIDorON/OFF
:5A@250V atResistiveLoad(HeatingOutput)
:3 A@250V atResistiveLoad(Humidificating, Alarm
andEggtrayrotatorOutput
:Maximum30mA,Maximum15V
:8mmRed4digitLEDDisplay
:8mmGreen4digitLEDDisplay
:P (Green),%(Green), C(Red), F(Red), Alarm(Red),
HumidifierOutput(Red),EggtrayrotatorOutput(Red)
HeatingOutput(Red),
: 83dB
:,
W
W
³
Z Z
V
V
, orProNem
o o
7. AutoTuneMetod
Starting Auto Tune (Limit Cycle Tuning)
Operation by the user :
•Adjust t
•Adjust auto tune selection parameter ( = )
• In the main screen and Temperature value
are should alternately.
“Atun”
emperature control on/off or PID parameter
( =1)
Auto Tune method is used for determining PID parameters used by the device.
If Auto Tune operation is finished without any problem,
the device saves the new PID coefficients, calculated
using the previously found “T” and “B” values, to
memory and continue to run.
parameter is adjusted automatically.
Temperature
Value
Time
Heating
Output
Time
B
T
Cancelling Auto Tune (Limit Cycle Tuning) operation :
1 - If sensor breaks;
2 - If auto tune operation can not be completed in 8 hours ;
3 - If user adjusts parameter ;
4- During auto tune operation if the user changes the temperature control from pid to on/off;
5 - If process set value is changed while auto tune operation is being performed;
Auto tune is canceled. “Atun” is not displayed. Then, without doing any changes in PID
parameters, device continues to run with previous PID parameters.
3- In main operating screen if the upper display is blinking, it means that temperature alarm exits and
alarm output is active . 1 5if buzzer function selection is , or 8 internal buzzer starts to operate.
4- In main operating screen if the lower display is blinking, it means that humidity alarm exits and alarm
output is active . 2 6if buzzer function selection is , or 8 internal buzzer starts to operate.
B C D E FG HI /
/
UV W Z/
/ 0
PowerSupplyVoltageA
TemperatureSensorInputB Scale( )°C/°F
ESM-3722
(77x35DINSize)
4
-20°C/-4°F; 80°C/176°F
115V ( %15)50/60Hz-1.5VAV±
ProNemMiniPMI-P
PT 100,IEC751(ITS90)
1
PTC(Not-1)
2
5230V ( %15)50/60Hz-1.5VAV±
8 10-30V 1.5W
Z
0°C/32°F;100°C/212°F
0°C/32°F;100°C/212°F
NTC(Not-1)
3
0°C/32°F;100°C/212°F
324V ( %15)50/60Hz-1.5VAV±
0
224V ( %15)50/60Hz-1.5VAW±
0%-100%
0%-100%
0%-100%
0/2..10VdcVoltageInput
4
50/4..20mA CurrentInput
6
HumiditySensorInputC Scale(%)
ProNemMiniPMI-P
0/2..10VdcVoltageInput
4
50/4..20mA CurrentInput
6
01 RelayOutput(3A@250V ,atResistiveLoad,1NO)V
HumidifierOutput
FG
1RelayOutput(5 A@250V ,atResistiveLoad1NC,1NO)V
HeatingOutputE
2SSRDriveOutput(Maximum30mA,Maximum15V)
01 RelayOutput(3A@250V ,atResistiveLoad,1NO)V
EggTryRotatorOutputHI
1RelayOutput(3A@250V ,atResistiveLoad,1NO)V
AlarmOutput
U
Temp.SensorwhichisgivenwithESM-3722
V
0None
3NTC-M5L20.K1.5 (NTCProbethermoplasticmouldedwith
1.5mcableforcoolingapplication)
4NTC-M6L50.K1.5 (
)
NTCProbestainlesssteelhousingwith
1.5mcableforcoolingapplication
9
ProNemMiniPMI-P (2 for TemperatureandHumidity
application)
.5mcable
6
Customer
1PTC-M6L40.K1.5(PTC AirProbe1.5msiliconcable)
2PTCS-M6L30.K1.5.1/8”(PTCLiquidProbewith1.5msiliconcable)
A
Userdefined
Userdefined
ESM-3722
ü
ESM-3722
ü
ESM-3722
ü
ESM-3722
ü
ESM-3722
ü
ESM-3722
ü
ESM-3722
ü
ESM-3722
ü
ü
PTC,NTC,PT-100
0/2..10V,0/4..20mA or
ProNemMiniPMI-P
6
2.3PanelMountingandRemoving
5.ChangingandSavingTemperatureandHumiditySetValue
5.1Ch miditySetValue
MainOperatingScreen
WhenSET buttonpressed‘’S’’ ledwill
beactiveandtemperaturesetvaluewill
bedisplayed.
TemperatureSetValueScreen
Temperaturesetvaluecan
bechangedwithincrement
anddecrementbuttons.
WhenSET buttonpressed
temperaturesetvaluecanbesaved.
GoesHumiditySET
valuescreen.
Temperaturesetvalueparameter(Default=37.4 )
Temperaturesetvalue,canbeprogrammedbetweenminimumtemperaturesetvalue and
maximumtemperaturesetvalue .
°C
WhenSET buttonpressed
setvaluecanbesaved.
Humidity
Goesbackto
mainoperationscreen.
HumiditySetValue Screen
If no operation is performed in Humidity set value changing mode and temperature set value
changing mode for 20 seconds, device turns to main operation screen automatically.
i
HumiditySetValue Screen
5.1 ProgrammingModeParameterList
In ON/OFF control algorithm, temperature
value is tried to keep equal to set value by
opening or closing the last control element.
ON/OFF controlled system, temperature
value oscillates continuously. Temperature
value’s oscillation period or amplitude around
set value changes according to controlled
system. For reducing oscillation period of
temperature value, a threshold zone is formed
below or around set value and this zone is
named hysteresis.
Temperature Sensor Offset Parameter ( Default = 0 )
3.2DeviceLabelandConnectionDiagram
3.ElectricalWiringDiagram
3.1SupplyVoltageInputConnectionoftheDevice
4.FrontPanelDefinitionand AccessingtotheMenus
5
7 8 11
9 10
12
BUTTON DEFINITIONS
1. Increment Button :
2. Decrement, Silencing Buzzer Button :
3. Manual Start of Egg Tray Rotator Operation Button:
**
4. Set Button:
5.Alarm led :
6. Heating Output Led :
7.Celcius led :
8.Fahrenheit led :
9. Led :
10. Output Led :
11.Precent Sign ledi :
12.Program led :
** In main operation screen, press this button to change display temperature and humidity sensor
value.
** It is used to increase the value in the Temperature and Humidity Set screens and Programming mode.
** It is used to decrease the value in the Set screen and Programming mode.
** It is used to silence the buzzer.
When the button is released the
engine start will be passive and engine stops.
** In the main operation screen; if this button pressed for the first time, Temperature set value will be
displayed. Value can be changed using increment and decrement buttons. When Set button is pressed
again, value is saved and Humidty set value will be displayed next. Value can be changed using
increment and decrement buttons. When Set button pressed again, value is saved and returns back to
main operating screen.
** To access the programming screen; in the main operation screen, press and hold this button for 5
seconds.
** It is used to save value in the Set screens (Temperature or Humidity) and programming screen.
**
** This led indicates that heating output is active.
** Indicates that device is in C mode.
** Indicates that device is in F mode.
** This led indicates that is active.
** This led indicates that output is active.
** Indicates that device is in programming mode .
o
o
In the main operation screen, if this button pressed engine starts.
It is active when alarm statuses.
Egg Tray Rotator Output
Humidity
** Indicates that device is in Humidity Set screen.
LED DEFINITIONS
Egg Tray Rotator Output
Humidificating
230V CONNECTION DIAGRAMV
TemperatureControlSelectionParameterOn/OfforPID (Default=0)
On - Off selected.
PID selected.
PID - Proportional Control Parameter ( Default =50 )
This parameter value can be adjusted form 0 to 100.
PID - Integral Parameter( Default = 1000 )
This parameter value can be adjusted form 0 to 3600.
PID - Derivative Parameter ( Default = 250 )
This parameter value can be adjusted form 0 to 3600.
PID -Period Time Parameter ( Default = 1 )
This parameter value can be adjusted form 1 to 50 second.
HumiditySensorScaleSelectionParameter(Default=0)
Buzzer Function Selection Parameter( Default = 0 )
Button Protection Parameter ( Default = 0 )
Humidity Alarm Function Selection Parameter ( Default = 0 )
Humidity (Default = 0)
When power is first applied to the device, this time delay must be expired for activation of
Humidity alarm.
Alarm Delay After Power On Parameter
It can be adjusted from 0 to 99 minutes.
Humidity Set Maximum Parameter(Default =Maximum Value of Device Scale)
if humidity alarm is active, this parameter value can be adjusted from humidity alarm set
minimum parameter to maximum value of the device scale.
Alarm
Humidity (Default = 0)
Humidity
Alarm On Delay Time Parameter
AlarmOnDelay Timecanbedefinedwiththisparameter.Itcanbeadjusted
from0to99minutes.
Buzzer is inactive.
Buzzer is active during temperature alarm
Buzzer is active during humidity alarm
Buzzer is active during Temperature sensor failures.
Buzzer is active during Humidity sensor failures.
Buzzer is active during Temperature sensor failures or temperature alarm.
Buzzer is active during Humidity sensor failures or Humidity alarm.
Buzzer is active during Temperature sensor failures or Humidity sensor failures
Buzzer is active during Temperature sensor failures or Humidity sensor failures
or temperature alarm or humidity alarm.
There is no protection.
Temperature setvalue can not be changed.
Humidity set value can not be changed.
Manual engine start is not available.
Humidity set value and Temperature set value can not be changed
Humidity set value can not be change and Manual engine start is not available.
Temperature set value can not be change and Manual engine start is not
available.
Temperature set value and Humidity set value can not be changed. Also
Manual engine start is not available.
Humiditysetvalueparameter(Default=60%)
Humiditysetvalue,canbeprogrammedbetweenminimumHumiditysetvalue andmaximum
temperaturesetvalue .
1-Before mounting the device in your panel, make
sure that the cut-out is of the right size.
2-Insert the device through the cut-out. If the
mounting clamps are on the unit, put out them
before inserting the unit to the panel.
3- Insert the mounting clamps to the fixing sockets
that located left and right sides of device and
make the unit completely immobile within the
panel
1-Pull mounting clamps from left and right
fixing sockets.
2-Pull the unit through the front side of the
panel
Before starting to remove the unit
from panel, power off the unit and
the related system.
c
Make sure that the power supply voltage is the same indicated on
the instrument.
Switch on the power supply only after that all the electrical
connections have been completed.
Supply voltage range must be determined in order. While installing
the unit, supply voltage range must be controlled and appropriate
supply voltage must be applied to the unit.
c
There is no power supply switch on the device. So a power supply
switch must be added to the supply voltage input.
Power switch must be two poled for seperating phase and neutral,
On/Off condition of power supply switch is very important in
electrical connection.
External fuse that on power supply inputs must be on phase
connection.
External fuse that on power supply inputs must be on (+)
connection.
V
Z
c
PowerSupplyInput
c
a
External
Fuse
(1A T)
Note-1
Supply
Switch
7 8
LN
Supply Voltage
230V ( %15) 50/60Hz ,
115V ( %15) 50/60Hz ,
24V ( %15)50/60Hz ,
24V ( %15) 50/60Hz ,
Z
V
V
V
W
±
±
±
±
10...30 V 1.5 W
Mustbedeterminedinorder.
ON
OFF
Temperature
Control
Output
Set
thSt
Time
thSt
Time
ü
3
4
1
2
5 6
9 10
7 8
11
12
TemperatureSetValueScreen HumiditySetValue Screen
Humiditysetvaluecanbe
changedwithincrementand
decrementbuttons.
RelayOutputs
2
135
468
7910
P/N: ESM-3722
L
N
a
PowerSupplyVoltage
230V ( %15) 50/60Hz ,
115V ( %15) 50/60Hz,
24V ( %15) 50/60Hz ,
24V ( %15) 50/60Hz ,
Z
V
V
V
W
±
±
±
±
10...30 V 1.5 W
11 12
TemperatureSensorInput
NTC,PTC,PT-100or
ProNemMiniPMI-P
HumiditySensorInput
0/2..10V,0/4..20mA or
ProNemMiniPMI-P
Mustbedeterminedinorder.
3
2
1
1
2
Mustbedeterminedinorder.
Mustbedeterminedinorder.
N
L
7 8 9 10
a
3x3 @250VA V
5A @250VV
LN
230 V ±15%
50/60Hz-1.5VA
V
2 3 41
ALARM
HUM.
5 6 11 12
14A TFuse
+
-
ENGINE
HEAT
N
L
7 8 9 10
a
3x3 @250VA V
5A @250VV
LN
230 V ±15%
50/60Hz-1.5VA
V
2 3 41
ALARM
HUM.
5 6 11 12
14A TFuse
+
-
ENGINE
HEAT
PTC Temperature and 0/4..20mA Humidity Sensor Input connection
VCC
GND
SCL
SDA
ProNem Mini PMI-P Temperature and Humidity Sensor Input Connection
Note: If this parameter is select 0, PID parameters ( , , , , ) will be not observed.
If this parameter select 1, parameter will be not observed.
Auto Tune (Limit Cycle Tuning) Selection Parameter ( Default = )
Device does not do(Limit cycle Tuning) operation.
Device does operation.
HysteresisParameterforTemperature(Default=0.1°C)
From 1 to 10°C for NTC,PTC, PT-100 (0°C, 100°C) ,From 1 to 18°F for NTC,PTC ,PT-100
(32°F, 212°F),From 0.1 to 10.0°C for NTC, PTC, PT-100 (0.0°C,100.0°C), From 0.1 to
18.0°F for NTC, PTC, PT-100 (32.0°F,212.0°F) ,From 1 to 10°C for ProNem Mini PMI-P
(-20°C, 80°C) ,From 1 to 18°F for ProNem Mini PMI-P (-4°F,176°F), From 0.1 to 10.0°C for
ProNem Mini PMI-P (-20.0°C,80.0°C), From 0.1 to 18.0°F for ProNem Mini PMI-P
(-4.0°F,176.0°F).
Minimum Temperature Set Value Parameter ( Default = 10.0°C)
Temperature set value can not be lower than this value. This parameter value can be
adjusted from minimum value of device scale to maximum temperature set value
parameter
Maximum Temperature Set Value Parameter ( Default = 40.0 °C )
Temperature set value can not be greater than this value.
This parameter value can be adjusted from minimum temperature set value parameter
to maximum value of the device scale.
From -10 to 10°C , NTC,PTC , PT-100 (0°C, 100°C)
From -18 to 18°F, NTC,PTC , PT-100 (32°F, 212°F)
From -10.0 to 10.0°C , NTC ,PTC , PT-100 (0.0°C,100.0°C)
From -18.0 to18.0°F NTC, PTC , PT-100 (32.0°F,212.0°F)
From -10 to 10°C ,ProNem Mini PMI-P ( -20°C, 80°C )
From -18 to 18°F,ProNem Mini PMI-P ( -4°F, 176°F )
From -10.0 to 10.0°C, ProNem Mini PMI-P ( -20.0°C, 80.0°C )
From -18.0 to18.0°F, ProNem Mini PMI-P ( -4.0°F,176.0°F )
0..10V 0..20mAZ Zor
2..10V 4..20mAZ Zor
(1) (2)
(2)(1)
It is valid, if the device type 0/2...10V
It is valid, if the device type 0/4...20mA
Z
Z
Humidity Sensor Input.
Humidity Sensor Input .
(1)
(2)
i
Analogue input range is determined with this parameter.
Note : parameter ProNem Mini PMI- type device are not observed.P
HysteresisParameterforHumidity(Default=1)
From 1 to 10 for Humidity Sensor (0%RH, 100%RH)
From 0.1to 10.0 for Humidity Sensor (0.0%RH,100.0%RH)
In ON/OFF control algorithm,
value is tried to keep equal to set value by
opening or closing the last control element.
ON/OFF controlled system, temperature
value oscillates continuously. Temperature
value’s oscillation period or amplitude
around set value changes according to
controlled system. For reducing oscillation
period of temperature value, a threshold
zone is formed below or around set value
and this zone is named hysteresis.
Humidity
ON
OFF
Humidity
Control
Output
Set
hhSt
Time
hhSt
Time
Maximum Humidity Set Value Parameter (Default = Maximum Value of Device Scale)
This parameter value can be
adjusted from minimum humidity set value parameter to maximum value of the
device scale.
Humidity set value can not be greater than this value.
Minimum Humidity Set Value Parameter (Default = Minimum Value of Device Scale)
set value can not be lower than this value. This parameter value can be adjusted
from minimum value of device scale to maximum set value parameter
Humidity
Humidity
Sensor Offset Parameter ( Default = 0.0 )Humidity
From -10 to 10 for Humidity Sensor (0%RH, 100%RH)
From -10.0 to 10.0 for Humidity Sensor (0.0%RH,100.0%RH)
Timeof AutomaticEggTrayRotator (Default=00:00)
Thisparametervaluecanbeadjustedform00:00to99:00minute/second.
Repeatcycleof AutomaticEggTrayRotator (Default=00:00)
Thisparametervaluecanbeadjustedform00:00to24:00hour/minute.
Alarm Output Function Selection Parameter ( Default = 0 )
Alarm is inactive.
Alarm-Temperature sensor failures.
Alarm-Humidity sensor failures.
Alarm-Temperature or Temperature sensor failures.
Alarm-Humidity or Humidity sensor failures.
Alarm-Temperature sensor failures or Humidity sensor failures.
Alarm-Temperature or Humidity or Temperature sensor failures or Humidity
sensor failures.
Note : if parameter value is 3 or 6 , , , , , or parameters are
observed.
Note : if parameter value is 4 or 6 , , , , , or parameters are
observed.
Temperature Alarm Set Parameter
Thisparametervaluecanbeprogrammedbetweentemperatureminimumalarmset
parameterandtemperaturealarmsetmaximum parameter.
( Default = 50.0 °C )
Temperature Alarm Function Selection Parameter ( Default = 0 )
Process High alarm selected.
Process Low alarm selected.
Deviation Band alarm selected.
Deviation Range alarm selected.
Alarm Set Maximum Parameter ( Default = Maximum Value of Device Scale)
if temperature alarm is active, this parameter value can be adjusted from temperature
alarm set value parameter to maximum value of the device scale.
Alarm Set Minimum Parameter (Default = Minimum Value of Device Scale)
if temperature alarm is active, this parameter value can be adjusted from minimum value of
device scale to temperature alarm set maximum parameter value.
Temperature Alarm Parameter
This parameter value can be adjusted form 0 to %50 of the device scale.
Hysteresis ( Default = 0)
Temperature AlarmOnDelayTimeParameter
Temperature AlarmOnDelay Timecanbedefinedwiththisparameter.Itcanbe
adjustedfrom0to99minutes.
(Default=0)
Temperature Alarm Delay After Power On Parameter
It can be adjusted from 0 to 99 minutes.
( Default = 0)
When power is first applied to the device, this time delay must be expired for activation of
temperature alarm.
Process High alarm selected.
Process Low alarm selected.
Deviation Band alarm selected.
Deviation Range alarm selected.
Humidity AlarmSetParameter
Thisparametervaluecanbeprogrammedbetweenhumidityminimumalarmset
parameterandhumidityalarmsetmaximum parameter.
(Default=50)
Humidity Set Minimum Parameter(Default =Minimum Valueof Device Scale)
if humidity alarm is active, this parameter value can be adjusted from minimum value of
device scale to humidty alarm set maximum parameter value.
Alarm
Humidity Alarm Parameter
This parameter value can be adjusted form 0 to %50 of the device scale.
Hysteresis ( Default = 0)
Buzzer ActiveTime
Ifbuzzerfunctionselectionparameter
Buzzeractivetimecanbedefinewiththisparameter.Itcanbeadjustedfrom1to99
minutes.Whenthisparameteris1,ifdecrementbuttonispressed, isobserved.In
thisconditionbuzzerisactivetillbuzzersilencebuttonispressed.
(Default= )
value=0,thisparameterisnotobserved.
Note-1: External Fuse is recommended
WHITE
YELLOW
BROWN
GREEN
ProNemMini
PMI-P
BLACK
Shield
Note: (Black)pinmustbeconnectedtonumber10(GND)oftheterminalblock.Shield
P/N:ESM-3722-5.2.5.0.1/01.01/1.0.0.0
7 8
a
3x3A@250V V
5A @250VV
L
230 V ±15%
50/60Hz -1.5VA
V
2 3 41
ALARM
PTC
5 6
ENGINE
HEAT
L N NNN N
0/4-20mA
HUM.
HUM.
INPUT
TEMP.
INPUT
9 10 11
P/N:ESM-3722-5.6.6.0.1/01.01/1.6.6.0
7 8 9 10
a
3x3A@250V V
5A @250VV
L
230 V ±15%
50/60Hz-1.5VA
V
2 3 41
ALARM
5 6
ENGINE
11 12
HEAT
L N NNN N
HUM.
ProNemMiniPMI-P
WHITE
BROWN
YELLOW
GREEN
VCC
GND
SCL
SDA
5.1 ProgrammingModeParameterList
Decimal Seperator Enabling Parameter ( Default = 0 )
None.
Only Temperature parameters with decimal seperator.
TemperatureUnitSelectionParameter (Default=0)
°C selected.
°F selected.
Only Humidity parameters with decimal seperator.
Only Temperature and Humidity parameters with decimal seperator.
Note : When value of or parameters are changed , the values of , , , ,
, , , , , , , , , , , , and parameters
should be changed accordingly.
0..10V veya 0..20mAZ Z
2..10V veya 4..20mAZ Z
Temperature SensorScaleSelectionParameter(Default=0)
(1) (2)
(2)(1)
Analogue(T inputrangeisdeterminedwiththisparameter.emperature)
Temperature
or
or
SensorScaleLowLimitParameter:(Default=0)
It can be adjusted from -1999 to ( -1). At this value analogue input becomes;
If =0,accordingtothedevicetype0V 0mA
If =1,accordingtothedevicetype2V 4mA
Z Z
Z Z
(1) (2)
(1) (2)
Temperature
or
SensorScaleHighLimitParameter:(Default=100)
Itcanbeadjustedfrom( +1)to9999. Atthisvalueanalogueinputbecomes;
According to the device type 10V 20mAZ Z
(1) (2)
Note : , parameters are shown, if the Temperature sensor analogue input type is selected .
Note : , and parameters are shown, if the Temperature sensor input type
( ) is selected.
analogue
0/2..10V or 0/4..20mA
ESM-3722
ü ü
ESM-3722
ESM-3722
ü ü
ESM-3722
ü
ESM-3722 ESM-3722
ü
Programming Mode Accessing Password
It is used for accessing to programming mode. It can be adjusted from 0 to 9999. If it is 0,
password is not entered for accessing to the parameters. When the password screen is not
set as “12” , If the user enters ‘12’ in password screen and parameters are
accessed and they can changed.
( Default = 0 )

Product specificaties

Merk: Emko
Categorie: Thermostaat
Model: ESM-3722

Heb je hulp nodig?

Als je hulp nodig hebt met Emko ESM-3722 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Thermostaat Emko

Emko

Emko Eco Light Handleiding

11 Juni 2024
Emko

Emko ESM-4900 Handleiding

27 November 2023
Emko

Emko CHANNEL8N Handleiding

27 November 2023
Emko

Emko ESM-4920 Handleiding

27 November 2023
Emko

Emko ESM-3722 Handleiding

27 November 2023
Emko

Emko ESM-9945-N Handleiding

27 November 2023
Emko

Emko ESD-9950-N Handleiding

6 Juni 2023

Handleiding Thermostaat

Nieuwste handleidingen voor Thermostaat

Tru Components

Tru Components TCN4S-24R Handleiding

18 December 2024
Tru Components

Tru Components TK4S-14RC Handleiding

18 December 2024
Tru Components

Tru Components TX4S-14R Handleiding

17 December 2024
Warmup

Warmup 5iE Handleiding

16 December 2024
Warmup

Warmup +Kit Handleiding

16 December 2024
Nobo

Nobo Connect SWT-IZW Handleiding

15 December 2024
Nobo

Nobo Connect SWT-IZB Handleiding

11 December 2024
Hive

Hive Thermostat Handleiding

10 December 2024
GENERAL Life

GENERAL Life HT15S Handleiding

9 December 2024
GENERAL Life

GENERAL Life HT15 Handleiding

9 December 2024