Elektrobock Pocket Home PH-SP2 Handleiding

Elektrobock Receiver Pocket Home PH-SP2

Lees hieronder de ๐Ÿ“– handleiding in het Nederlandse voor Elektrobock Pocket Home PH-SP2 (4 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 58 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Version 11.02
Wireless receiver for control of
electric heating devices
- WALL-MOUNTED -
PH-SP2
Operating instructions
Control of electric heating systems
Component of the PocketHome
ยฎsystem
Two-way radio communication at 433,92 MHz
The connected electric appliance is switched according to
the required temperature
The control unit PH-BSP is the pilot component
The device can only be installed by a person with adequate qualification!
The installation must be executed in a voltage-free state!
holes for
installation
on KU/KP68
Fig.1 Fig.2 Fig.3
230 V/ 50 Hz
Wiring diagram:
L
N
FUNCTION BUTTON:
SHORT PRESSING - coding.
LONG PRESSING (for about 5 s) - RESET
deleting the code from the memory (the green and
red LEDs flash simultaneously).
max.
16 A
Fig.4
INSTALLATION
output terminals
power supply
terminals
FUNCTION
BUTTON
PH-SP2 is used for switching the heating device in connection
with the PH-BSP control unit.
ACTIVATION PROCEDURE
1. Lift off the front cover of the receiver acc. to Fig. 1, 2.
2. Attach the receiver to the wall (or to the wiring box directly).
3. Switch off the main circuit breaker.
4. Connect the receiver acc. to the diagram.
5. Connect the receiver to the mains 230 V / 50 Hz.
6. Switch on the main circuit breaker; the green diode flashes
on the receiver; thus the receiver is ready for further setting.
7. Shortly press the FUNCTION BUTTON
for about 1.5 s (the green and red
diode are flashing alternately).
8. On the PH-BSP control unit, press theโ€ Test โ€
button in the ACTIV mode to activate the
SP switching components (see page 10 of
the PH-BSP instructions).
9. If the code has been learned correctly,
the green and red diodes flash
simultaneously.
INDICATION DIODES
LED 2LED 1
empty memory, code not learned
code learned
FLASHING ALTERNATELY= code learning mode
FLASHING SIMULTANEOUSLY= code has been learned
SIMULTANEOUS LONG FLASH= code was ERASED
relay switched
ERROR (if no signal is received from the
transmitter within approx. 6 hours, it switches to
the 2-min-ON / 8-min-OFF mode). LED flashes
only if the relay is on, i.e. for 2 minutes.
EXPLANATION: LIT UNLIT FLASHING
FUNCTION


Product specificaties

Merk: Elektrobock
Categorie: Receiver
Model: Pocket Home PH-SP2

Heb je hulp nodig?

Als je hulp nodig hebt met Elektrobock Pocket Home PH-SP2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Elektrobock

Handleiding Receiver

Nieuwste handleidingen voor Receiver

Akg

Akg IVM4500 IEM Handleiding

14 November 2024
Yamaha

Yamaha XMV8140 Handleiding

14 November 2024
Yamaha

Yamaha TX4n Handleiding

14 November 2024
Yamaha

Yamaha XMV4140 Handleiding

14 November 2024
Yamaha

Yamaha PC6501N Handleiding

14 November 2024
Yamaha

Yamaha PC3301N Handleiding

14 November 2024
Yamaha

Yamaha PC4801N Handleiding

14 November 2024
Yamaha

Yamaha P1000S Handleiding

14 November 2024
Yamaha

Yamaha PC9501N Handleiding

14 November 2024