Electro Harmonix Pitch Fork Handleiding

Electro Harmonix Niet gecategoriseerd Pitch Fork

Lees hieronder de 📖 handleiding in het Nederlandse voor Electro Harmonix Pitch Fork (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Pitch Fork

POLYPHONIC PITCH-SHIFTER/HARMONY PEDAL

Congratulations on your purchase of the Electro-Harmonix , a compact, Pitch Fork

battery powered, polyphonic pitch-shifter/harmony pedal. The transposes Pitch Fork

the pitch of your instrument over a range of up to +/- 3 octaves. Three different

available pitch-shifting modes allow the pitch to be transposed up, down or both

simultaneously in Dual mode. The pitch shift amount can be set to a fixed interval or

continuously varied by an expression pedal control voltage. Tor he Pitch Fork’s

footswitch features two different modes of operation: Latch and Momentary.

Momentary allows rapid toggling between effect and bypass for quick blasts of pitch

bending The BLEND knob is a wet/dry control allowing you create the perfect mix . to

of your dry and transposed signals.

WARNING: Your PITCH FORK comes equipped with an Electro-Harmonix 9.6DC-200BI power

supply (same as used by Boss® & Ibanez®: 9.6 Volts DC 200mA). The PITCH FORK requires

30mA at 9VDC with a center negative plug or runs off a 9Volt battery. Using the wrong adaptor

or a plug with the wrong polarity may damage your PITCH FORK and void the warranty.

GETTING STARTED

Connect the output plug of the supplied power adaptor to the 9V power jack Plug .

your strument into the INPUT jack; connect your amp to the OUTPUT jack Set the in .

toggle switch to UP arrow and press the LATCH button so it is down. Turn BLEND

fully clockwise and set SHIFT to 1, as in 1 octave up. Press the footswitch until the

LED lights up. You will hear all your notes shifted up 1 octave. Connect an optional

expression pedal to continuously y the pitch from unity up to 1 octave. var

Press the LATCH button it is up. The footswitch now has a momentary action: so

when pressed the effect activates and pitch is shifted; when released, the effect is

bypassed Connect an expression pedal to control glissando rate of the momentary .

footswitch. If the EXP jack is vacant, pitch will change at the default glissando rate of

60ms (this is user adjustable).

BLEND KNOB

The BLEND knob mixes between the untreated, analog dry signal and the effected

signal. At BLEND’s full clockwise position, the output is 100% wet.

SHIFT KNOB

The SHIFT knob selec the maximum interval of chromatic transposition. The chart ts

below shows how the pitch will be shifted relative to the original pitch.

Detune

Minor

2nd

Major

2nd

Major

3rd

Perfect

4th

Perfect

5th

Major

6th

M r ino

7th

Oct

MODE TOGGLE SWITCH

The MODE toggle switch selects whether the pitch is shifted up, down or both

simultaneously relative to the root. Dual mode outputs two pitch-shifted signals One .

of the shifted signals follows the SHIFT knob as if in UP mode. The other shifted

signal creates a musically useful harmony according to the SHIFT knob setting.

DUAL mode SHIFT knob Settings:

Detune

Deep

Detune

down

1 Oct

down

1 Oct

down

2 Oct

1 Oct

down

3 Oct

1 Oct

down

LATCH BUTTON

The LATCH button selects Latch or Momentary mode This affects how the footswitch .

and EXP jack input behave. When the LATCH button is down, Latch mode is enabled.

The footswitch toggles between effect and bypass each time you press and release

the footswitch; the EXP input continuously varies pitch. When the LATCH button is in

the up position, Momentary mode is selected. The effect is only on while the

footswitch is held down, otherwise the Pitch Fork is bypassed; the EXP input varies

the glissando rate of the momentary footswitch.

BYPASS FOOTSWITCH & STATUS LED

The footswitch toggles between effect on and buffered bypass. In Latch mode, each

press and release of the footswitch toggles between effect and bypass modes. In

Momentary mode, when the footswitch is held down, the effect is on, when the

footswitch is released, the Pitch Fork enters bypass. The status LED lights when in

Effect mode.

EXP JACK

EXPression input jack accepts a TRS expression pedal connector a T -Sleeve 0- or ip 5V

control voltage input expression pedal should ideally use a 10k potentiometer . The

with linear rather than audio taper. It must have the wiper connected to TIP and toe-

down connected to RING. Pedals made by some manufacturers do not conform to

this convention, and would need a special cable to swap RING and TIP. Some

suggested Expression Pedals: EHX Expression Pedal, M-Audio® -P, MoogEX ® -2 EP &

EP-3, Roland® -5 or BossEV ® -500L. FV

 LATCH MODE - the Expression/CV input controls pitch shift amount,

ranging from unity, or no pitch shift, in the heel position to the interval set

by the SHIFT knob for the toe position. Pitch varies continuously from heel

to toe in all settings.

 MOMENTARY MODE - the Expression/CV put controls glissando rate for in

the Pitch Fork’s footswitch. When the bypass footswitch is pressed, the Pitch

Fork jumps from bypass to the pitch shift interval set by the SHIFT knob.

The amount of time it takes to reach the interval setting is the SHIFT knob’s

glissando rate When the footswitch is released, pitch will return to unity by .

the same rate. When your expression pedal is heel-down the rate is 4ms, in

toe-down the rate is 2sec. When no device is plugged into the EXP input the

default glissando rate is ms. 60

SAVING NEW GLISSANDO RATE SETTING FOR PITCH FORK FOOTSWITCH

1) Set LATCH mode button to the Momentary or up position.

2) Connect expression pedal or CV device to EXP jack.

3) Press and release Pitch Fork’s footswitch while adjusting expression pedal or CV

device until you hear sired glissando rate. Leave external device in current de

setting.

4) Press and hold down the footswitch. Pitch Fork’s

5) Press LATCH button so it changes to Latch mode. LED flashes to confirm.

6) Release the footswitch.

7) The new glissando rate is now saved. Remove plug inserted into EXP jack,

change back to Momentary mode and use footswitch to confirm new rate.

RESTORING FACTORY DEFAULT FOR GLISSANDO RATE

1) Make sure nothing is plugged into EXP jack.

2) Set LATCH button to Latch mode, the down position.

3) Press footswitch so that Pitch Fork is in Bypass.

4) Press and hold down . the Pitch Fork’s footswitch

5) Press LATCH button so it changes to Momentary mode. LED flashes to confirm.

6) Release the footswitch.

OUTPUT JACK

Outputs the wet/dry mix set by the BLEND knob.

CHANGING BETWEEN LATCH AND MOMENTARY WHEN EXPRESSION PEDAL

IS CONNECTED

When in Latch mode and you switch to Momentary mode the expression pedal

position is ignored. The stored glissando rate will take precedence until the

expression pedal is moved from current position.

LED ON STARTUP

The LED will blink 4 times then hold on the 5th if in latch mode or toggle off if in

momentary. This happens when AC power is applied or you plug into the input jack

with fresh battery installed. If battery power is too low, the LED blinks dimly, every a

other second.

CHANGING THE BATTERY

To change the 9-volt battery, you must remove the 4 screws on the bottom of the

Pitch Fork. Once the screws are removed, you can take off the bottom plate and

change the battery. Please do not touch the circuit board while the bottom plate is off

or you risk damaging a component. extend battery life, disconnect the INPUT jack To

when the Pitch Fork is not in use.

NOTES AND SPECIFICATIONS

 PITCH FORK has high quality buffered bypass.

  Input impedance is 2.2M .

  Output impedance is 680 .

 Current draw of the PITCH FORK is 30mA.

- WARRANTY INFORMATION -

Please register online at http://www.ehx.com/product-registration or complete and

return the enclosed warranty card within 10 days of purchase. Electro-Harmonix will

repair or replace, at its discretion, a product that fails to operate due to defects in

materials or workmanship for a period of one year from date of purchase. This

applies only to original purchasers who have bought their product from an authorized

Electro-Harmonix retailer. Repaired or replaced units will then be warranted for the

unexpired portion of the original warranty term. If you should need to return your

unit for service within the warranty period, please contact EHX Customer Service at

718 937- -8300 or info@ehx.com for a Return Authorization Number. Along with your

pedal, please include a brief description of the problem as well as your name,

address, telephone number, copy of your receipt, and a check or money order.

United States - $12 Ship to:

Canada - $15 Electro-Harmonix

Europe and outside countries - $25 C/O New Sensor Corporation

55-01 2nd Street

Long Island City, NY, 11101

Attn: Service Department

Please make checks/money orders payable to New Sensor Corporation.

To hear demos on all EHX pedals visit us on the web at www.ehx.com

Email us at info@ehx.com

- FCC COMPLIANCE -

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation. If the

device is not installed and used in accordance with the instructions, it may cause harmful

interference to radio communications and void the user's authority to guarantee the equipment.

Note:

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:



Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.



Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.



Consult the dealer or an experienced radio/TV technician for help .

Modifications not expressly approved by the manufacturer could void the user's authority to

operate the equipment under FCC rules.

Product specificaties

Merk:	Electro Harmonix
Categorie:	Niet gecategoriseerd
Model:	Pitch Fork

Heb je hulp nodig?

Als je hulp nodig hebt met Electro Harmonix Pitch Fork stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Electro Harmonix

Electro Harmonix Memory Boy Handleiding

16 November 2024

Electro Harmonix Soul POG Handleiding

16 November 2024

Electro Harmonix OD Glove Handleiding

16 November 2024

Electro Harmonix Crayon 69 Handleiding

16 November 2024

Electro Harmonix Good Vibes Handleiding

12 November 2024

Electro Harmonix Cock Fight Handleiding

9 Juli 2024

Electro Harmonix Cock Fight Plus Handleiding

9 Juli 2024

Electro Harmonix Holy Grail Max Handleiding

9 Juli 2024

Electro Harmonix The Worm Handleiding

17 Juni 2024

Electro Harmonix Canyon Echo Handleiding

12 Juni 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Panasonic NB-W250 Handleiding

25 November 2024

Alpine CHM-S611 Handleiding

25 November 2024

AOpen DE3650-C Handleiding

25 November 2024

Lazer Urbanize MIPS Handleiding

25 November 2024

Symmons Dia 353GB-24 Handleiding

25 November 2024

SoundTube IPD-RS62-EZ Handleiding

25 November 2024

Moen Camerist 4905 Handleiding

25 November 2024

Lazer Cameleon DLX Handleiding

25 November 2024

DMT DLD-85 Handleiding

25 November 2024

AOpen AM1120T Handleiding

25 November 2024