Electro Harmonix Next Step Crying Bass Handleiding

Electro Harmonix Niet gecategoriseerd Next Step Crying Bass

Lees hieronder de 📖 handleiding in het Nederlandse voor Electro Harmonix Next Step Crying Bass (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
CRYING BASS
WAH/FUZZ PEDAL FOR BASS
Congratulations on your purchase of the Electro-Harmonix a wah Crying Bass:
pedal, with fuzz, designed specifically for bass! The sweeps the wah Crying Bass
filter without using any moving parts: it does not use a potentiometer, optics or
magnetism. The result is a responsive pedal that allows precise control over a
brilliantly fluid wah. The Crying Bass also includes a fuzz circuit to add extra
harmonics to your bass sound, giving the wah filter more frequencies to chew on, as
well as a fixed low pass filter (LPF) for extra low end.
GETTING STARTED
Plug your guitar into the INPUT jack; connect your amp to the OUTPUT jack. Within
seconds the EHX logo in the center of the pedal will light. Your Crying Bass is ready
to go! Please note: as long as a plug is inserted into the INPUT jack, a drain is placed
on the 9V battery inside the Crying Bass. It is recommended that you disconnect the
INPUT jack when the Crying Bass is not in use to extend battery life.
FUZZ Control
The fuzz in the Crying Bass helps to accentuate the wah effect, adding distortion and
harmonics to your bass notes. The FUZZ dial located on the INPUT side of the Crying
Bass is a blend control for the fuzz circuit. As the numbers increase on the dial, the
volume of the fuzz effect increases while the dry volume decreases. The maximum
setting of 10 should yield a volume boost as compared to your bypass volume.
LPF VOL Control
The Crying Bass includes a 2nd-Order Low Pass Filter (LPF) fixed at 194 Hz for adding
more bottom end to the wah effect. Dial-in just the right amount of LPF by using the
LPF VOL control located near the INPUT jack. The volume of the LPF increases as the
numbers increase on the dial. The LPF is muted when set to 0. The maximum setting
of 10 should yield a low end boost as compared to your bypass volume.
CALIBRATION
To ensure the Crying Bass responds to its full sweep range, it may be necessary to
calibrate the sweep of the Crying Bass when it is used on a different surface since its
last use. It is particularly important to calibrate if the Crying Bass is used on a slanted
surface. We recommend calibrating the Crying Bass after unwrapping it from its
packaging, during your first use of the pedal.
CALIBRATION PROCEDURE
1. Place the pedal on the surface where it will be used.
2. Ensure the Crying Bass is sitting flat on the surface then press and release
the CALIBRATE button once; the EHX logo begins to blink indicating the toe
position has been saved.
3. While the EHX logo continues to blink, rock the pedal all the way back to the
extreme heel position and hold it there.
4. Press and release the CALIBRATE button once more.
5. The EHX logo will stop blinking to indicate that the heel position has been
saved.
If you accidentally press the CALIBRATE button and the EHX logo blinks, do not press
CALIBRATE again. After approximately 7 seconds, the Crying Bass will stop blinking
and ignore the button press.
ENTERING/EXITING BYPASS
Toggle between and effect mode by tipping the Crying Bass buffered bypass
forward, in the toe direction, past the flat position of the Crying Bass. You do not
need to tip the Crying Bass all the way forward; 25% of the total forward travel will
do it. The Crying Bass needs to return to its flat position before you can toggle
between bypass and effect mode again.
When the Crying Bass is in effect mode, the EHX logo in the center of the pedal will
light up. In bypass mode, the logo does not light.
POWER
Plugging into the INPUT jack activates power from the internal 9 Volt battery. The
input cable should be removed when the unit is not in use to avoid running down the
battery. If an AC Adapter is used, the Crying Bass will be powered up as long as the
AC Adapter is correctly plugged in.
The Crying Bass’s power jack is located on the same side as the OUTPUT jack. A 9
Volt AC Adapter capable of delivering at least 50 mA of current is required to power
the Crying Bass. The inner ring of the 9 Volt AC Adapter must be negative, the outer
ring positive. The optional 9V power supply from Electro-Harmonix is 9.6DC-200BI
(same as used by Boss® & Ibanez®) 9.6 Volts DC/200mA. The unit’s battery may be
left in or taken out when the AC Adapter is in use. The actual current draw of the
Crying Bass is 18 mA.
CHANGING THE BATTERY
1. Locate the battery door at the front of the Crying Bass, under the toe area
of the top plate.
2. Remove the large black screw that holds the battery door to the case, most
coins or larger slotted screwdrivers can be used to remove this screw.
3. Connect your new 9V battery to the wired battery connector.
4. Insert the 9V battery into the battery holder clip on the battery door so that
the wired connector is on the same side of the hole in the battery door.
5. Place the battery door back into its window in the case of the Crying Bass
and re-install the screw.
NOTES AND SPECIFICATIONS
• Crying Bass has buffered bypass.
•  The input impedance presented at the INPUT Jack is 1M . The output
impedance at the OUTPUT Jack is 1.8k .
• The current draw of the Crying Bass is 18 mA.

Product specificaties

Merk: Electro Harmonix
Categorie: Niet gecategoriseerd
Model: Next Step Crying Bass

Heb je hulp nodig?

Als je hulp nodig hebt met Electro Harmonix Next Step Crying Bass stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Electro Harmonix

Electro Harmonix

Electro Harmonix Memory Boy Handleiding

16 November 2024
Electro Harmonix

Electro Harmonix Soul POG Handleiding

16 November 2024
Electro Harmonix

Electro Harmonix OD Glove Handleiding

16 November 2024
Electro Harmonix

Electro Harmonix Crayon 69 Handleiding

16 November 2024
Electro Harmonix

Electro Harmonix Good Vibes Handleiding

12 November 2024
Electro Harmonix

Electro Harmonix Cock Fight Handleiding

9 Juli 2024
Electro Harmonix

Electro Harmonix Cock Fight Plus Handleiding

9 Juli 2024
Electro Harmonix

Electro Harmonix Holy Grail Max Handleiding

9 Juli 2024
Electro Harmonix

Electro Harmonix The Worm Handleiding

17 Juni 2024
Electro Harmonix

Electro Harmonix Canyon Echo Handleiding

12 Juni 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Panasonic

Panasonic NB-W250 Handleiding

25 November 2024
Alpine

Alpine CHM-S611 Handleiding

25 November 2024
AOpen

AOpen DE3650-C Handleiding

25 November 2024
Lazer

Lazer Urbanize MIPS Handleiding

25 November 2024
Symmons

Symmons Dia 353GB-24 Handleiding

25 November 2024
SoundTube

SoundTube IPD-RS62-EZ Handleiding

25 November 2024
Moen

Moen Camerist 4905 Handleiding

25 November 2024
Lazer

Lazer Cameleon DLX Handleiding

25 November 2024
DMT

DMT DLD-85 Handleiding

25 November 2024
AOpen

AOpen AM1120T Handleiding

25 November 2024