Electro Harmonix Nano Pulsar Handleiding

Electro Harmonix Niet gecategoriseerd Nano Pulsar

Lees hieronder de 📖 handleiding in het Nederlandse voor Electro Harmonix Nano Pulsar (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
Congratulations on your purchase of the Nano Pulsar, a variable shape stereo
tremolo and panner effects pedal. Connected in mono, the Nano Pulsar is a
tremolo that allows signicant control over the shape of the modulating
waveform. Connect the Nano Pulsar in stereo (each output to a separate amp/
mixer channel) and you have a panner pedal that will send your instrument
back and forth between two amps with the same control over waveform shape.
So, while one amp is fading up in volume, the other will be fading down in
volume or even more dramatic: while one amp is on, the other is off. But that’s
not all! Higher settings of the DEPTH knob put the Nano Pulsar into warp mode
where the signal’s volume modulates asymmetrically producing rhythmic,
out-of-phase tremolo effects.
Operating Instructions
Connect your guitar or other instrument to the INPUT jack on the Nano Pulsar
and the MONO/L OUTPUT to your main amp. If running the Nano Pulsar in
stereo, connect the Right OUTPUT jack to another amplier. Apply power if
needed; your Nano Pulsar might already have a 9V battery installed. Press
the footswitch to ensure the STATUS LED is lit, now your Nano Pulsar is
ready to go.
For a nice starter setting, turn all knobs to their 12 o’clock positions and set
the toggle switch—centered within the knobs—to the Triangle position. This
setting will yield a deep, smooth tremolo at a medium rate. Lower the DEPTH
knob for a shallower tremolo effect; play with the RATE knob to hear the
full range of modulation speed on tap; and of course, adjust the VOL knob
for more or less volume at the output jacks.
- 2 -
1. VOL Knob Adjusts the overall output level of the effect. As VOL is turned clock-
wise, the output gets louder. The VOL knob offers up to 12dB of volume boost
depending on the settings of the other controls. When VOL is turned fully counter-
clockwise the effect output is silenced.
2. SHAPE Switch Selects between Triangle and Square Wave modes. See more on
Shape in the SHAPE knob section.
3. SHAPE Knob Further adjusts the tremolo’s modulation waveform shape.
Triangle Wave Mode The modulation waveform is triangle wave based,
resulting in smooth volume modulation. As the SHAPE knob is turned
clockwise from the minimum position to the center, the waveform morphs
from rising sawtooth to triangle. Turning SHAPE further clockwise from the
center position to maximum, the waveform continues to morph from triangle
to falling sawtooth. Please note: the triangle shapes are reversed out of the
Right OUTPUT jack. For example, at the minimum SHAPE setting, the right
output will be a falling sawtooth.
Controls and Connections
- 3 -
Square Wave Mode The modulation waveform is square wave based, re-
sulting in sharp, on/off volume modulation. As the SHAPE knob is turned
clockwise from minimum to maximum, the modulating waveform’s pulse
width increases from a narrow pulse to a wide pulse width. Near the knob’s
center position is square wave modulation where the tremolo volume is
loud and quiet in equal amounts. Please note: the square shapes are re-
versed out of the Right OUTPUT jack. For example, at the minimum SHAPE
setting, the right output will be a wide pulse width.
4. DEPTH Knob Adjusts the amount of tremolo that will be applied to your signal.
As DEPTH is turned clockwise from minimum to maximum, the amount of the
tremolo effect increases. Maximum tremolo—greatest dynamic range from loud-
est to quietest—occurs when the DEPTH knob is set to approximately 1 o’clock. As
DEPTH is turned further clockwise past 1 o’clock, the tremolo begins to warp by
modulating between positive and negative phase with an asymmetric or rhythmic
feel. Set DEPTH to approximately 1 o’clock to obtain the widest stereo eld
when the Nano Pulsar is used as a stereo panner.
5. RATE Knob Adjusts the speed of the tremolo or pan effect. As RATE is turned
clockwise the modulation rate increases. The range of modulation speed is ap-
proximately 20 seconds to 30 Hz.
6. FOOTSWITCH and STATUS LED – Press and release the footswitch to toggle
between buffered bypass and effect mode. When in effect mode, the Status LED
is lit and pulses at the same rate as the effect. The Status LED is off in buffered
bypass mode. The Nano Pulsar powers up in bypass mode.
7. INPUT Jack Audio input to the Nano Pulsar.
8. MONO/LEFT OUTPUT Jack Connect this ¼” mono jack to your amplier’s input.
When using the Nano Pulsar as a mono device we recommend you use the MONO/L
jack so that the SHAPE knob description on the previous page corresponds to
what you hear.
9. RIGHT OUTPUT Jack Connect this ¼” mono jack to your second amplier’s input.
When using the Nano Pulsar as a stereo panner, use the R OUTPUT jack for your
second channel. You can connect only to the RIGHT OUT jack if you like; the tremolo
effect will be the same as from the LEFT OUT jack but the SHAPE waveforms are re-
versed. For example, when the SHAPE knob is set to maximum, tremolo modulation
out of the Right Output will either be a rising sawtooth or narrow pulse width.
10. 9V Power Jack – An optional 9VDC, center-negative power supply can be connected
to the power jack to provide power without a battery. The Nano Pulsar requires
30mA at 9VDC on a center-negative plug. Do not exceed 12VDC at the power jack.
When using a 9V battery, plugging into the INPUT jack activates power. The input cable
should be removed when the unit is not in use to avoid running down the battery.
To change the 9-volt battery, you must remove the 4 screws on the bottom of
the Nano Pulsar. Once the screws are removed, you can take off the bottom plate
and change the battery. Please do not touch the circuit board while the bottom
plate is off or you risk damaging a component.

Product specificaties

Merk: Electro Harmonix
Categorie: Niet gecategoriseerd
Model: Nano Pulsar

Heb je hulp nodig?

Als je hulp nodig hebt met Electro Harmonix Nano Pulsar stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Electro Harmonix

Electro Harmonix

Electro Harmonix Memory Boy Handleiding

16 November 2024
Electro Harmonix

Electro Harmonix Soul POG Handleiding

16 November 2024
Electro Harmonix

Electro Harmonix OD Glove Handleiding

16 November 2024
Electro Harmonix

Electro Harmonix Crayon 69 Handleiding

16 November 2024
Electro Harmonix

Electro Harmonix Good Vibes Handleiding

12 November 2024
Electro Harmonix

Electro Harmonix Cock Fight Handleiding

9 Juli 2024
Electro Harmonix

Electro Harmonix Cock Fight Plus Handleiding

9 Juli 2024
Electro Harmonix

Electro Harmonix Holy Grail Max Handleiding

9 Juli 2024
Electro Harmonix

Electro Harmonix The Worm Handleiding

17 Juni 2024
Electro Harmonix

Electro Harmonix Canyon Echo Handleiding

12 Juni 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Panasonic

Panasonic NB-W250 Handleiding

25 November 2024
Alpine

Alpine CHM-S611 Handleiding

25 November 2024
AOpen

AOpen DE3650-C Handleiding

25 November 2024
Lazer

Lazer Urbanize MIPS Handleiding

25 November 2024
Symmons

Symmons Dia 353GB-24 Handleiding

25 November 2024
SoundTube

SoundTube IPD-RS62-EZ Handleiding

25 November 2024
Moen

Moen Camerist 4905 Handleiding

25 November 2024
Lazer

Lazer Cameleon DLX Handleiding

25 November 2024
DMT

DMT DLD-85 Handleiding

25 November 2024
AOpen

AOpen AM1120T Handleiding

25 November 2024