Electro Harmonix Nano Metal Muff Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Electro Harmonix Nano Metal Muff (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Nano Metal Muff
with Noise Gate
Congratulations on your purchase of the Nano Metal Muff, a pocket-sized offering of
EHX’s classic Metal Muff. The Nano Metal Muff utilizes three powerful EQ bands and a
newly added noise gate to tame unwanted noise and hum between riffs. The Nano
Metal Muff offers commanding bass, sculpted mids, and defined high coupled with s
user-controlled distortion from pinched-edge to totally crushing making it a true
heavy metal machine.
C ONTROLS
DIST Knob Adjusts the amount of distortion and saturation. Turn clockwise for
more saturation.
GATE Knob Removes unwanted hum by adjusting the noise floor threshold. The
gate mutes the OUTPUT jack when the signal at the INPUT jack is below the threshold
setting of the GATE knob. As GATE is turned clockwise, a louder guitar signal at the
INPUT jack is required to unmute the OUTPUT jack Set GATE fully counter-clockwise .
to disable.
Setting the GATE knob: start with GATE fully counterclockwise, DIST above noon, and
your guitar volume at max, you may want to hold the strings so they don’t ring out.
Slowly turn GATE clockwise until the Nano Metal Muff mutes. Now turn GATE a little
further clockwise and then test it. If you have to play with too much force to unmute
the gate then turn GATE a little counter-clockwise. If you want the gate to act more
quickly at the end of notes, turn GATE further clockwise.
GATE LED This LED lights when the internal gate mutes the output signal. When
the GATE LED is off, the signal is allowed to pass through to the output jack.
VOL Knob Sets the overall output level.
BASS Knob Provides up to 14dB of cut and boost in the bass frequency range.
MID Knob Provides up to 15dB of cut and boost in the middle frequency range.
TREBLE Knob Provides up to 10dB of cut and boost in the treble frequency range.
BYPASS Footswitch & STATUS LED Toggles the Nano Metal Muff between effect
and buffered bypassed. The STATUS D lights when the pedal is engaged. LE
C & P ONNECTIONS OWER
INPUT Jack Nano Metal Muff. The input This ¼” jack is the audio input to the
impedance presented at the INPUT jack is 1M . Ω
OUTPUT Jack Nano Metal Muff. In This ¼” jack is the audio output from the
Bypass mode, the OUTPUT jack is connected to the INPUT jack through a buffer
circuit. The output impedance at the OUTPUT Jack is 600 . Ω
9V Power Jack An optional 9VDC, center-negative power supply can be inserted
into this jack to power the Nano Metal Muff. The Nano Metal Muff requires mA at 24
9VDC on a center-negative plug. Do not exceed at the power jack. 12V
When using a 9V battery, plugging into the INPUT jack activates power. The input
cable should be removed when the unit is not in use to avoid running down the
battery.
To change the 9-volt battery, you must remove the 4 screws on the
bottom of the Nano Metal Muff. Once the screws are removed, you can
take off the bottom plate and change the battery. Please do not touch the
circuit board while the bottom plate is off or you may damage a
component.
N & S OTES PECIFICATIONS
Audio input impedance at INPUT jack: 1MΩ
Audio output impedance at OUTPUT jack: 600Ω
Current draw: mA 24
Maximum input signal level in bypass, before clipping +8.5 : dBu
To achieve its biting distortion, the Nano Metal Muff has very high maximum gain.
This requires that both the pickups and cables be well shielded and properly
grounded to avoid excessive hum when high sustain control settings are used.
C OMPLIANCE
Note:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help .
Modifications not expressly approved by the manufacturer could void the user's authority to
operate the equipment under FCC rules.
The CE logo indicates that this product has been tested and shown to conform with all
applicable European Conformity directives.
The logo indicates that this product is made up of electronic WEEE or “trashcan”
components that should not be trashed alongside household waste but instead should
be recycled by a proper electrical waste facility.


Product specificaties

Merk: Electro Harmonix
Categorie: Niet gecategoriseerd
Model: Nano Metal Muff

Heb je hulp nodig?

Als je hulp nodig hebt met Electro Harmonix Nano Metal Muff stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Electro Harmonix

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd