Electro Harmonix HOLIEST GRAIL Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Electro Harmonix HOLIEST GRAIL (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 19 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
1
HOLIEST GRAIL
- DESCRIPTION -
The Holiest Grail is built around a high quality stereo reverb algorithm coupled with a
painstakingly developed simulation of spring reverb as found in guitar amps and dedicated
reverb tanks. The decay time, damping and diffusion parameters of the reverb can be
freely tweaked to design an infinite array of natural and unnatural sounding spaces. A
versatile pre-delay can be applied to the reverb, and a feedback control has been added to
the pre-delay to provide even greater sound-sculpting capabilities for spatial simulation
and/or experimentation.
As an aid to both live performance and recording, the box is able to store 8 user presets
and can be remotely controlled via MIDI. A standard expression footpedal can be used to
control the amount of signal sent to the reverb, a performance tool that can help
personalize the sound.
- CONTROLS/INDICATORS -
INPUT
--------------------------------------------------------------------------------------------
INPUT GAIN Slider –
A control for setting optimal analog signal level into the A/D
Converter. The green LED lights when there is sufficient level. The red LED will light when
clipping occurs.
The position of the INPUT GAIN Slider is not saved with the user
presets.
WARNING: Use only the 9VDC/500mA AC adapter the Holiest Grail comes
supplied with. Do not use any other AC adapters. Using other AC adapters, even
those made by Electro-Harmonix, could cause harm to the unit, the adapter or you.
The Holiest Grail does not use batteries.
2
Signal LED
– Green LED above INPUT GAIN Slider. The Signal LED varies in brightness
depending on the strength of the input signal. The louder the signal the brighter this LED
will be.
Clip LED
– Red LED above INPUT GAIN Slider. The Clip LED lights when the signal clips
the A/D Converter. Ideally you want the largest possible signal entering the A/D Converter
without clipping. One way to achieve the ideal signal level is to raise the INPUT GAIN Slider
until the CLIP LED starts to blink and then lower the INPUT GAIN Slider slowly until the
CLIP LED stops lighting.
REVERB Design
------------------------------------------------------------------------------------------------------------
Pre-delay Controls
TIME Slider –
Controls the length of time between striking a note on your
instrument and the start of the reverb. For maximum usability, the slider has
two ranges of usage: between 0% and 50%, the predelay time can be adjusted
from 0 to 100 ms with an accuracy of approximately 1.5 ms. From 50% to
100%, the time ranges from 100ms to 440ms in 5 ms increments.
FEEDBACK Slider –
Controls the amount of feedback that is re-circulated in the
pre-delay before the reverb. At its maximum setting an infinite loop will be
created. At the lowest level the pre-delay simply delays the sound of the reverb
without any special effects. When the FEEDBACK Slider is set somewhere in the
middle, your original note will enter the Reverb a number of times.
Reverb Controls
DECAY Slider –
Controls the length of the reverb time. This affects the
apparent size of space. At maximum setting an infinite reverb may occur,
depending on the other settings.
DAMPING Slider
– Affects the frequency response of the reverb over time. A
setting of 0% has more damping and thus the reverb is muted. As the slider is
pushed up, the reverb sounds more bright and ‘open’. Higher settings (less
damping) also yield a longer reverb time.
DIFFUSION Slider
– Works in conjunction with the other parameters to
provide a density control to make subtle variations in the quality of the reverb
3
sound. At the lowest setting, the reverb has a grainier quality, while at the
maximum setting the reverb is at its most lush.
Output Mixer Controls
DRY Output Level Slider
– Controls the amount of dry signal sent to the
outputs. The dry signal is mixed into both the left and right output channels. At
maximum setting, 100% signal is output.
SPRING Output Level Slider
– Controls the amount of spring simulation
effect sent to the outputs. The spring signal is mixed into both the left and right
output channels. A higher setting makes the output “spring-ier.”
REVERB Output Level Slider
– Controls the amount of stereo reverb signal
sent to outputs. A higher setting yields more reverb signal.
PRESET Management
--------------------------------------------------------------------------------------------
PRESET/FREE MODE Slide Switch–
When in Preset Mode, programs can be saved and
loaded. When in Free Mode, all preset capability is disabled and all parameters are derived
from their slider values. (What you see is what you get!) In Free Mode, the Preset A and B
Footswitches have no function.
PRESET BANK Slider
– Selects the bank (1-4) to use when saving or loading presets. In
Free Mode, this slider has no function.
PRESET A Footswitch
– Tap this footswitch to load Preset A. Hold down the footswitch
for approximately 5 seconds to save a preset to position A.
PRESET B Footswitch
– Tap this footswitch to load Preset B. Hold down the footswitch
for approximately 5 seconds to save a preset to position B.
Preset A LED
– Lit solid when Preset A is loaded. Blinks when saving to Preset A.
Preset B LED
– Lit solid when Preset B is loaded. Blinks when saving to Preset B.


Product specificaties

Merk: Electro Harmonix
Categorie: Niet gecategoriseerd
Model: HOLIEST GRAIL

Heb je hulp nodig?

Als je hulp nodig hebt met Electro Harmonix HOLIEST GRAIL stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Electro Harmonix

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd