Electro Harmonix Hell Melter Handleiding

Electro Harmonix Niet gecategoriseerd Hell Melter

Lees hieronder de 📖 handleiding in het Nederlandse voor Electro Harmonix Hell Melter (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 189 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
Congratulations, you are now possessed by the Hell Melter. This device
is built to produce the legendary ‘chainsaw’ distortion tone, but with
added features that expand the threat of tonal destruction. Do you
want the gruesome vintage grind found on classic death metal records?
Do you seek added volume, distortion, clarity, or control? Sink deep
into the Hell Melter and you shall nd all the havoc you’ll ever need.
Operating Instructions
Connect your guitar to the INPUT jack of the Hell Melter and the OUTPUT
jack to your amp’s input. Plug in the included power supply and plug its
output plug into the Hell Melter’s power jack. Press the EFFECT footswitch
to ensure the red LED is lit, and the Hell Melter is ready.
A good starting point is to turn all the knobs (except for DRY LVL and GATE)
to their maximum positions and play the heaviest riffs you've got. Setting
all the EQ knobs to maximum, including MID FREQ, produces the uniquely
punchy “chainsaw” sound that has powered countless heavy bands.
Note: the original circuit that produced this sound used components
with wide tolerances, resulting in noticeable tone differences from unit
to unit. The Hell Melter can recreate many of these different tones with
slight tweaks near the maximum position of the MID FREQ knob.
POWER SUPPY REQUIREMENTS:
Voltage: Current: 9VDC 140mA Center-Negative Polarity:
This device comes equipped with an Electro-Harmonix 9.6DC-200 power supply. Use of the wrong adapt-
er or a plug with the wrong polarity may damage the device and void the warranty. Do not exceed 12VDC
on the power plug. Power supplies rated for less than 140mA can cause the device to act unreliably
Advanced Heavy Metal Distortion
- 2 -
1. DISTORTION Knob Adjusts the amount of distortion and saturation, from a
light grind to a roaring chainsaw. Turn clockwise for more distortion.
2. LEVEL Knob Adjusts the overall output level of the Hell Melter. Turn clockwise
for more output. More output is available than on the original ‘chainsaw’ circuit.
3. LOW Knob Provides active boost or cut to the bass frequency range. The middle
position leaves bass frequencies at.
4. MID LVL Knob Provides active boost or cut to the mid frequency, with the
frequency set by the MID FREQ knob. The middle position leaves mid frequen-
cies at.
5. MID FREQ Knob Adjusts the frequency boosted or cut by the MID LVL knob.
Turn the knob clockwise to increase the frequency.
Controls and Connections
- 3 -
6. HIGH Knob Provides active boost or cut to high frequencies. The middle posi-
tion leaves high frequencies at. Tip: the frequencies controlled by the HIGH
Knob are slightly lower than a typical ‘treble’ control, allowing you to produce
searing highs without a lot of treble harshness. To emphasize even higher
‘treble’ frequencies, turn the HIGH knob below the middle position, and increase
the LEVEL knob to re-emphasize treble.
7. NORM/BURN Switch Switches between “Normal” and “Burn” Modes:
Normal Mode The famous vintage chainsaw distortion sound.
Burn Mode A custom, modernized distortion sound, utilizing higher voltage
rails and alternative clipping options. This results in a less compressed and
more open distortion sound with a more pronounced attack.
8. GATE Mini Knob Removes unwanted hum by adjusting the noise oor thresh-
old. The gate mutes the OUTPUT jack when the signal at the INPUT jack is below
the threshold setting of the GATE knob. As GATE is turned clockwise, a louder
guitar signal at the INPUT jack is required to unmute the OUTPUT jack. Set GATE
fully counter-clockwise to disable.
Setting the GATE knob: Start with GATE fully counterclockwise, DIST above noon,
and your guitar volume at max. You may want to hold the strings so they don’t
ring out. Slowly turn GATE clockwise until the Hell Melter mutes. Now turn GATE
a little further clockwise and then test it. If you have to play with too much force
to unmute the gate, then turn GATE a little counter-clockwise. If you want the
gate to act more quickly at the end of notes, then turn GATE further clockwise.
9. DRY LVL Mini Knob Adds clean, undistorted input signal to the output. As the
knob is turned clockwise, the amount of dry signal increases. At the minimum
position, no dry signal is mixed into the output. Tip: this is especially useful to
maintain note clarity when stacking the Hell Melter with a dirty amp or another
gain pedal.
10. EFFECT Footswitch and Red LED This footswitch engages or bypasses the
effect. The LED lights when the effect is active. The Hell Melter employs high
quality buffered bypass.
11. BOOST Footswitch and Yellow LED This footswitch engages Boost Mode, add-
ing extra gain at the input of the circuit, and adjustable volume boost.
12. BOOST LEVEL Internal Trimmer This trimmer controls the additional volume
added when Boost Mode is active. To access it, remove the 4 screws on the back
plate of the Hell Melter, and locate the trimmer next to the BOOST Footswitch.
Taking care not to touch the rest of the circuitry of the board, turn this trimmer
clockwise using a small at-head screwdriver to increase the volume boost. At
the minimum position, Boost Mode provides no volume boost.
13. INPUT Jack Audio input to the Hell Melter.
14. OUTPUT Jack Audio output from the Hell Melter.
15. 9V Power Jack Attach the output plug from the included power supply to the
9V power jack. The Hell Melter draws 140mA at 9VDC on a center-negative plug.
Do not exceed 12VDC on the power jack. The Hell Melter does not take batteries.

Product specificaties

Merk: Electro Harmonix
Categorie: Niet gecategoriseerd
Model: Hell Melter

Heb je hulp nodig?

Als je hulp nodig hebt met Electro Harmonix Hell Melter stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Electro Harmonix

Electro Harmonix

Electro Harmonix Memory Boy Handleiding

16 November 2024
Electro Harmonix

Electro Harmonix Soul POG Handleiding

16 November 2024
Electro Harmonix

Electro Harmonix OD Glove Handleiding

16 November 2024
Electro Harmonix

Electro Harmonix Crayon 69 Handleiding

16 November 2024
Electro Harmonix

Electro Harmonix Good Vibes Handleiding

12 November 2024
Electro Harmonix

Electro Harmonix Cock Fight Handleiding

9 Juli 2024
Electro Harmonix

Electro Harmonix Cock Fight Plus Handleiding

9 Juli 2024
Electro Harmonix

Electro Harmonix Holy Grail Max Handleiding

9 Juli 2024
Electro Harmonix

Electro Harmonix The Worm Handleiding

17 Juni 2024
Electro Harmonix

Electro Harmonix Canyon Echo Handleiding

12 Juni 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Panasonic

Panasonic NB-W250 Handleiding

25 November 2024
Alpine

Alpine CHM-S611 Handleiding

25 November 2024
AOpen

AOpen DE3650-C Handleiding

25 November 2024
Lazer

Lazer Urbanize MIPS Handleiding

25 November 2024
Symmons

Symmons Dia 353GB-24 Handleiding

25 November 2024
SoundTube

SoundTube IPD-RS62-EZ Handleiding

25 November 2024
Moen

Moen Camerist 4905 Handleiding

25 November 2024
Lazer

Lazer Cameleon DLX Handleiding

25 November 2024
DMT

DMT DLD-85 Handleiding

25 November 2024
AOpen

AOpen AM1120T Handleiding

25 November 2024