Electro Harmonix Germanium 4 Big Muff Pi Handleiding

Electro Harmonix Niet gecategoriseerd Germanium 4 Big Muff Pi

Lees hieronder de πŸ“– handleiding in het Nederlandse voor Electro Harmonix Germanium 4 Big Muff Pi (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
1
GERMANIUM4 BIG MUFF PI
Dual Vintage Distortion and Overdrive
Congratulations on your purchase of the GERMANIUM4 BIG MUFF PI. The
GERMANIUM4 BIG MUFF PI is a new and versatile overdrive/distortion that
captures the essence of the warm sound unique to the germanium
transistors from the β€˜60s. The GERMANIUM4 BIG MUFF PI is two
independent circuits, one a distortion and one an overdrive, each with
completely independent controls. The two circuits can be used separately
or together. Each circuit has its own independent ON/OFF bypass
footswitch.
-CONTROLS-
DISTORTION SIDE: The DISTORTION side can be used independently
or with the OVERDRIVE side. When both sides are ON, the DISTORTION
side precedes the OVERDRIVE side in the signal chain. The DISTORTION
utilizes two germanium transistors and is capable of going from clean - to
a gritty overdrive - to a full on distortion and beyond.
GAIN CONTROL – This knob adjusts the amount of preamp gain for the
DISTORTION side of the pedal. As you turn the GAIN knob clockwise the
distortion and volume will increase dramatically.
BIAS CONTROL – This knob adjusts the character of the distortion by
changing the bias of the signal before it is distorted by the Germanium
transistors. Turning the BIAS knob counter-clockwise will result in a more
mellow and compressed tone. Turning the BIAS knob clockwise will result
in an edgy and more aggressive tone.
VOLTS CONTROL – This knob adjusts the amount of voltage supplied to
the DISTORTION side only. When the VOLTS knob is turned fully
clockwise, the circuit is receiving the full voltage. Turning the VOLTS knob
counter-clockwise will simulate a dying battery. As the voltage is lowered,
the signal will become more compressed, and start to clip, creating a wide
2
range of sonic textures to work with. NOTE: As the VOLTS knob is turned,
the sound may momentarily dip in volume as the signal adjusts to the new
voltage setting.
VOLUME CONTROL – This knob controls the output level of the
DISTORTION side of the pedal. Fully counter-clockwise will produce no
sound. As the VOLUME knob is turned clockwise, the output level will
increase to its maximum volume at the full clockwise setting.
OVERDRIVE SIDE: The OVERDRIVE side can be used independently or
with the DISTORTION side. When both sides are ON, the OVERDRIVE side
follows the DISTORTION side in the signal chain. The overdrive utilizes
two germanium transistors and can go from a nice fattening boost to a
warm overdrive. The overdrive reacts differently to different input levels.
Using hotter pickups, or having the DISTORTION side on will add a variety
of tonal options.
GAIN CONTROL – This knob adjust the amount of gain in the two
germanium transistor preamp gain stage for the OVERDRIVE side. The
gain will increase as the GAIN knob is turned clockwise. Overall, there is
less gain available on this side than the DISTORTION side. The overall
character of the gain will change depending on how the BIAS control is
set.
BIAS CONTROL – This knob adjusts the character of the distortion by
changing the bias of the signal in the preamp section of the overdrive
circuit. When the BIAS knob is at noon, the sound will be the clearest and
most dynamic. When the BIAS knob is fully counter-clockwise, the sound
will be more compressed. When the BIAS knob is fully clockwise, the
sound will start to clip and can add a great vintage grit to the overdrive.
TONE CONTROL – This knob is a single knob tone control. As the TONE
knob is turned clockwise, the tone of the OVERDRIVE side will change
from a low end emphasis to a high end emphasis.
VOLUME CONTROL – This knob controls the output level of the
OVERDRIVE side of the pedal. Fully counter-clockwise will produce no
sound. As the VOLUME knob is turned clockwise, the output level will
increase to its maximum volume at the full clockwise setting.
STATUS LED and FOOTSWITCH (DISTORTION) – When this LED is
lit; the GERMANIUM4 BIG MUFF PI DISTORTION effect is active. When the
LED is off, the DISTORTION side is in True Bypass Mode. The footswitch
engages/disengages this effect. The footswitch controls the true bypass
ON/OFF for the DISTORTION side.
3
STATUS LED and FOOTSWITCH (OVERDRIVE) – When this LED is lit;
the GERMANIUM4 BIG MUFF PI OVERDRIVE effect is active. When the LED
is off, the OVERDRIVE side is in True Bypass Mode. The footswitch
engages/disengages this effect. The footswitch controls the true bypass
ON/OFF for the OVERDRIVE side.
INPUT Jack – Connect your instrument to the input jack. The input
impedance of the GERMANIUM4 BIG MUFF PI is 200K ohms.
OUTPUT Jack – Connect this jack to your amplifier.
9V POWER JACK – The GERMANIUM4 BIG MUFF PI can run off of a 9V
battery or you can connect a 9VDC battery eliminator capable of delivering
at least 100mA to the 9V power jack. The optional 9V power supply from
Electro-Harmonix is 9.6DC-200BI (same as used by Bossβ„’ & Ibanezβ„’) 9.6
Volts DC 200mA. The power supply must have a barrel connector with
center negative. The battery may be left in or taken out when using a
power supply. The current draw for the GERMANIUM4 BIG MUFF PI is
12mA.


Product specificaties

Merk: Electro Harmonix
Categorie: Niet gecategoriseerd
Model: Germanium 4 Big Muff Pi

Heb je hulp nodig?

Als je hulp nodig hebt met Electro Harmonix Germanium 4 Big Muff Pi stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Electro Harmonix

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd