EK Water Blocks 3831109841020 Handleiding

EK Water Blocks Hardwarekoeling 3831109841020

Lees hieronder de 📖 handleiding in het Nederlandse voor EK Water Blocks 3831109841020 (2 pagina's) in de categorie Hardwarekoeling. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

All disclosures, noces and warranty condions are being wrien on the EKWB website. Please read terms of use. Revision 1.0. Released on September 18 th 2012!

Installation and mounting manual for -RES X3 EK series reservoir

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at for updates. Before www.ekwb.com

installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual before through before beginning with the installation process!

2. The EK High Flow and EK-PSC type fittings require only a small amount of force to screw them firmly place since the liquid seal is ensured by the rubber o-ring gaskets.in

3. The use of corrosion inhibiting coolants is always recommended for any liquid cooling system.

4. DO NOT USE any kind of alcohol or alcohol derivate with this reservoir or the acrylic tube may crack and fail! Do not clean it using alcohol either!

STEP 1: GENERAL INFORMATION. Factory provided EK-RES X3

series

reservoir

Congratulations on your purchase of EK-RES X3 series reservoir! By default the EK-RES X3 series reservoir comes with the following:

- -RES X3 EK

series

reservoir with preinstalled EK-RES X3 - Anticyclone

- -Multioption RES X2 Holder 60mm (2 pcs) EK

- Polyether an -vortex foam (H=15mm) ti

- Mounting mechanism:

o 4x G1/4 Plug

o 2x EK-G1/4 Extender

o Allen Key 6mm

STEP 2: INSTALLING THE RESERVOIR HOLDERS

EK-RES X3

series

reservoirs comes with a pair of special -Reservoir holders. These holders are meant to be installed directly on the computer chassis. User EK

may need to drill 2 (two) holes through chassis metal using electric power drill if there are no appropriate mounting holes available. Φ4mm

STEP 2.1

STEP 2.2

STEP 2.3

Use enclosed M4 screw, washer and

nut to mount the reservoir holder

through the pre-drilled hole to the

computer chassis.

Install reservoir onto reservoir holders.

Using a gentle force the reservoir will

easily 'click' into position. The clamps

should always hold onto acrylic tube and

not the acetal top or bottom.

Once the reservoir is positioned please use

enclosed 2.5mm Allen key to tighten the

hex head screw in order to clamp the

reservoir. Do not use high force. Partially

unscrew the aforementioned screw when

removing the reservoir.

Alternatively one can purchase various reservoir holders, such as EK-UNI Holder 50/70 (EAN: 3830046997715): One can use the EK-UNI Holder 50/70 if the

chassis lack the appropriate holes to install the reservoir and the drilling is out of the question. EK-UNI Holder 50/70 can be install on 5. Drive Bay cage and 25”

fixated with M4 screws and nuts to carry the Reservoir Holders.

For more reservoir add-ons please EK Webshop!

TUBE

EK-RES X3 Sealing gasket –

(O-Ring 52x2.5mm)

EK-RES X3 TUBE –

(64-, 104-, 204- or 354mm)

depending on the variant

EK-RES X3 Sealing gasket –

(O-Ring 52x2.5mm)

EK-RES X3 Ancyclone –

(Short, Long)

EK-RES X3 Reservoir Boom –

EK-RES X3 Reservoir Top –

All disclosures, noces and warranty condions are being wrien on the EKWB website. Please read terms of use. Revision 1.0. Released on September 18 th 2012!

STEP 3 (optional): USING POLYETHER ANTI-VORTEX FOAM:

EK-RES X3 series reservoir comes preinstalled with EK-RES X3 Anticyclone by default (long or short depending on the variant). In case your system suffers – –

from excessive vortex issues, air bleeding problems or if the pump is sucking in air you may replace the anticyclone with the enclosed polyether foam. There are

two ways to use the polyether anti-vortex foam:

Default configuration

PE foam use whole –

PE foam trim to fit recess –

This is the default configuration of

EK-RES X3

series

reservoir.

Use the foam as a whole to replace EK-

RES X3 Anticyclone. –

Trim the foam to size to fit into the

desired recess on the Reservoir Bottom.

STEP 4 RECOMMENDED RESERVOIR CONFIGURATION :

EK-RES X3 series reservoir features 5 (five) G1/4 threaded inlet/outlet openings on the Reservoir Bottom plus additional one on the Reservoir Top. In order for

reservoir to function properly one port must be used as an inlet and one as an outlet. Unused ports must be closed with plugs using enclosed 6mm Allen key!

GENERAL OVERVIEW OF ALL G1/4 THREADED PORTS:

IMPORTANT NOTES:

1. When using ports #3, #4 or #6 it is mandatory to use the enclosed EK-Extender G1/4 (EAN: 3831109845165) due the ports being recessed into the plastic

Reservoir Bottom.

2. When using EK-Extender G1/4 make sure not to use fittings or barbs with G1/4 thread longer than 5mm! All

EK-PSC

and

High Flow

fittings are

compatible!

3. When using ports #1 and #2 make sure not to use fittings or barbs with diameter larger than 25mm! All

EK-PSC

and

High Flow

fittings are compatible!

4. EK recommends the use of EK-PSC fittings. When using fittings other than EK-PSC series please use hose clamps or appropriate substitute to secure the

tubing to the barb. The use of biocide containing and corrosion inhibiting coolant is always recommended for any liquid cooling system.

5. Port #6 of EK-RES X3 series reservoir should only be used to connect this reservoir with external fill port!

TIPS AND ADVICES:

- Using a horizontal pass-through configuration (using ports #1 and #5 as inlet/outlet) will yield in most optimal hydraulic conditions but may result in

difficult initial bleeding of air in low restriction- or high pumping power water cooling systems.

- When using a bottom feeding vertical configuration (using ports #3 and #4 as inlet/outlet) you may experience severe vortex issues. Using a PE foam as

a whole to replace the EK-RES X3 Anticyclone will remedy this issue. Please see STEP 3!

- Visit EK Webshop to purchase various add-ons (such as reservoir holders, tube extenders, alternative reservoir tops and many more) for your EK-RES X3

series reservoir!

REQUIRED TOOLS AND ACCESSORIES:

philips screwdriver power drill with 4mm drill bit (oponal)

1- Horizontal Port

2- Horizontal Port

3- Vercal Port

4- Vercal Port

6- Vercal Port (Top)

5- Horizontal Port (back)

RECOMMENDED RESERVOIR CONFIGURATION:

Allen Key 6mm

EK-Plug G1/4

EK-PSC ng

Tubing

Product specificaties

Merk:	EK Water Blocks
Categorie:	Hardwarekoeling
Model:	3831109841020
Kleur van het product:	Black, Translucent
Gewicht:	370 g
Breedte:	60 mm
Diepte:	60 mm
Materiaal:	Acryl