BTI Aqua-Solutions HC2100 Handleiding
BTI Aqua-Solutions
Kraan
HC2100
Lees hieronder de π handleiding in het Nederlandse voor BTI Aqua-Solutions HC2100 (4 pagina's) in de categorie Kraan. Deze handleiding was nuttig voor 4 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4

FILTRATION FAUCET INSTALLATION INSTRUCTIONS
ITEM C2100
ITEM C2200
ITEM C2400
ITEM H2100
ITEM H2200
ITEM H2400
ITEM HC2100
ITEM HC2200
ITEM HC2400
SHUT OFF WATER SUPPLY
BEFORE INSTALLATION
Drill 3/4β to 1β in diameter hole in
countertop. Maximum counter
thickness is 2β
Center the base plate with built-in
O-ring over the mounting hole on
the top of the countertop. Center the
faucet body on the base plate.
If desired, apply a thin bead of silicone
seal under the base plate for added
sealing.
DO NOT USE PLUMBERSβ PUTTY
Place faucet handle in desired position.
Fasten the faucet from under the
countertop, sliding large rubber wash-
er, then metal washer, then smaller
rubber washer, then 5/8β diameter
serrated lock washer on the faucet
stem, and secure with the lock nut so
the faucet does not move/spin.
DO NOT OVER TIGHTEN
COLD ONLY FILTRATION FAUCET W/ FILTRATION SYSTEM
ITEMS: C2100, C2200, C2400
1 2 3
www.btiaquasolutions.com β’ 7022 S. Revere Parkway Suite 240 β’ Centennial, CO 80112 β’ 720.322.0800 (o) 720.322.0801 (f)
9-1/2β
7-1/2β
5-3/8β
3-1/4β
2-1/8β
9-1/2β
7-1/2β
5-3/8β
6-1/2β
2-1/8β
9-11/16β
4β
2-3/4β
2-1/8β
6-1/4β
3-1/4β
4-1/4β
9-11/16β
4β
2-3/4β
2-1/8β
6-1/4β
6-5/8β
9-3/4β
2-1/8β
2-3/4β
4β
6-3/4β
9-3/4β
2-1/8β
5-1/2β
4β
6-3/4β
C2100 / H2100 HC2100 C2200 / H2200 HC2200 C2400 / H2400 HC2400
REV. / /1811 19
TOOLS REQUIRED
ADJUSTABLE WRENCH β’ DRILL β’ PLUMBERSβ TAPE
PHILLIPS HEAD SCREWDRIVER
Faucet Stem
Base Plate
Rubber Washer
Metal Washer
Lock Washer
Lock Nut
Tube Insert
Ferrule
Compression Nut
1/4β Water Inlet
Tubing (supplied
with BTI Filtration
System FL1000)
Rubber Washer

FILTRATION FAUCET INSTALLATION INSTRUCTIONS, page 2 of 4
TIGHTEN SECURELY WITH WRENCH.
COLD ONLY FILTRATION FAUCET W/ FILTRATION SYSTEM
ITEMS: C2100, C2200, C2400
Once a clean flow of water is achieved, check for leaks, ESPECIALLY at the water supply and connection points. If leak(s) are
present, shut off the water supply, repair the leak and re-test the system as previously described.
4
Slide the metal 1/4β compression nut
over the supply tubing (provided with
the filtration system). Next, place the
plastic ferrule (large end first) over
the supply tubing into the compres-
sion nut.
If you are using the BTI Filtration
System ITEM FL1000, you have ample
tubing to connect to the faucet and
still leave 4 -6β of extra tubing before "
the connection point.
5
Place the 1/2β long plastic insert into
the end of the tubing and tighten the
compression nut on the faucet stem.
6
*COMPLETE FILTRATION SYSTEM
INSTALLATION USING INSTALLATION
GUIDE INCLUDED WITH YOUR SPECIFIC
BRAND OF FILTRATION SYSTEM.
Then, open the handle on the filtration
faucet and turn on the water supply.
Allow the water to run for 1-2 minutes
to clear any debris that might be present
in the water line.
7
FILTRATION SYSTEM INSTALLATION WITH BTI HOT/COLD FILTRATION FAUCET AQUA-SOLUTIONS
ITEMS: HC2100, HC2200, HC2400
A
B
C
D
E
F
F
G
(A) FILTRATION FAUCET
(B) BTI FILTRATION SYSTEM-FL1000
(C) LINE/HOSE TO KITCHEN FAUCET
(D) ANGLE SHUT-OFF VALVE (supplied)
(E) COLD-WATER SUPPLY SHUT-OFF VALVE
(F) 1/4β O.D. TUBING (supplied)
(G) 3/8β / 1/4β ADAPTER (supplied ) w/faucet
Install angle shut-off valve (D) supplied with BTI
Filtration System.
Shut-off cold-water supply (E). Disconnect line/
hose (C) to kitchen faucet from cold-water
supply shut-off valve (E).
Connect angle shut-off valve (D) to cold-water
supply shut-off valve (E). Connect line/hose from
kitchen faucet (C) to angle shut-off valve (D).
Cut the 1/4β O.D. inlet/outlet tubing (supplied) to
the correct lengths, ensuring the cut ends are
square and clean.
Push one end of tubing (F) into angle shut-off
valve (D). Push other end of tubing into
βL-Fittingβ, pre-installed in the βinletβ on top
of filter.
Connect 3/8β Female-Side of adapter (G)
(supplied) to braided blue label
cold-water in hose. Push one end of tubing
(F) into 1/4β Push-Fit Side of adapter (G).
Push other end of tubing (F) into βoutletβ
connector on top of filter.
To remove a tube, push down on the collet
while pulling on the tube.
Turn on the water supply and check for
leaks. Flush at least one gallon of water
through the system before use.
Write the installation and filter change
dates on the label for future reference.

FILTRATION FAUCET INSTALLATION INSTRUCTIONS, page 3 of 4
Drill 1-3/8β hole in countertop.
( )Maximum counter thickness is 2β
Center the base plate with built-in
O-ring over the mounting hole on
the top of the countertop. Center the
faucet body on the base plate.
If desired, apply a thin bead of silicone
seal under the base plate for added
sealing.
DO NOT USE PLUMBERSβ PUTTY
For Hot Only Faucet: Place faucet
handle in desired position.
Fasten the faucet from under the
countertop by ξ rst sliding the rubber
washe , then the metal washer onto r
the faucet stem.
Make sure to place the 3 screws on
the metal washer through the match-
ing holes of the rubber washer and
slide both washers up to the bottom of
the countertop.
HOT ONLY and HOT COLD FILTRATION FAUCET W/ DIGITAL INSTANT HOT WATER DISPENSER/ BTI AQUA-SOLUTIONS
ITEMS: H2100, H2200, H2400, HC2100, HC2200, HC2400, HT4105
1
2
3
Hoses are attached to faucet body as
shown in diagram.
A - Blue Label Cold Water-In Hose
B - Faucet Stem
C - Hot Only Faucet, Hot Handle
D - Black Label Pressure Tank Hose
E - Hot & Cold Faucet, Cold Handle
F - Blue Label Cold Water-In Hose
G - Faucet Stem
H - Black Label Pressure Tank Hose
I - Hot & Cold Faucet, Hot Handle
A
C
D
E
F
G
H
I
B
4
Place a metal pinch clamp on one -
end of the clear hose and attach the
clear hose to faucet stem end.
Secure with pinch clamp. -
5
Attach the braided blue label cold-
water-in hose to cold-water supply
line.
Use plumbersβ tape on the outside
threads to provide a good seal.
6
Thread the mounting nut to the top
of the faucet stem and hand tighten.
Once the faucet is secure, tighten the
3 screws against the underside of the
countertop. This will prevent the faucet
from moving/spinning.
7
Product specificaties
Merk: | BTI Aqua-Solutions |
Categorie: | Kraan |
Model: | HC2100 |
Heb je hulp nodig?
Als je hulp nodig hebt met BTI Aqua-Solutions HC2100 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Kraan BTI Aqua-Solutions

31 Maart 2025

31 Maart 2025

31 Maart 2025

31 Maart 2025

31 Maart 2025

31 Maart 2025

31 Maart 2025
Handleiding Kraan
- Kraan IKEA
- Kraan Etna
- Kraan Inventum
- Kraan Brita
- Kraan Delta
- Kraan Ernesto
- Kraan Franke
- Kraan Grohe
- Kraan Hansgrohe
- Kraan Hotto
- Kraan KitchenAid
- Kraan Livarno
- Kraan Lynx
- Kraan Miomare
- Kraan Quooker
- Kraan Smeg
- Kraan Stiebel Eltron
- Kraan Teka
- Kraan Concept
- Kraan Elba
- Kraan Blanco
- Kraan Caple
- Kraan CDA
- Kraan Curaqua
- Kraan SchΓΌtte
- Kraan Lamona
- Kraan Nodor
- Kraan Empire
- Kraan Brauer
- Kraan Elkay
- Kraan Oras
- Kraan Berg
- Kraan Mizzo
- Kraan ZLine
- Kraan Moen
- Kraan Mueller
- Kraan Aloni
- Kraan WillieJan
- Kraan Everpure
- Kraan Sani-Lav
- Kraan Fala
- Kraan Neo
- Kraan Lomazoo
- Kraan American Standard
- Kraan Livarno Lux
- Kraan Billi
- Kraan SaniSupreme
- Kraan Deante
- Kraan InSinkErator
- Kraan Omnires
- Kraan Vola
- Kraan Zip
- Kraan The Galley
- Kraan Viidako
- Kraan Waltec
- Kraan Gessi
- Kraan Puretec
- Kraan Sussex
- Kraan Fantini
- Kraan Oliveri
- Kraan Rogerseller
- Kraan Axor
- Kraan Graff
- Kraan Zurn
- Kraan Karran
- Kraan Symmons
- Kraan Jacuzzi
- Kraan Rohl
- Kraan ProFlo
- Kraan Pfister
Nieuwste handleidingen voor Kraan

31 Maart 2025

31 Maart 2025

31 Maart 2025

31 Maart 2025

31 Maart 2025

30 Maart 2025

30 Maart 2025

30 Maart 2025

30 Maart 2025

30 Maart 2025