DSC PG9933 Handleiding

DSC Rookmelder PG9933

Lees hieronder de 📖 handleiding in het Nederlandse voor DSC PG9933 (40 pagina's) in de categorie Rookmelder. Deze handleiding was nuttig voor 19 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/40

The PG9933 is designed to monitor the CO gas level in residential dwellings and give

early warning before dangerous levels are detected. This device is intended to be used

with a compatible wireless alarm system. The detector consists of an electrochemical

carbon monoxide sensor assembly coupled to a wireless transmitter.

The Wireless Carbon Monoxide Alarm communicates with the control panel and can

send alarm, tamper and battery condition messages to the system receiver.

CAUTION: The detector expiry date is stamped on the detector. After the

expiry date, the detector should not be used - do not wait for end- of-life indic-

ation!

CAUTION: Unauthorized removal of the unit from the mounting bracket will

initiate a tamper alert.

Warnings:

The PG9933 wireless Carbon Monoxide detector shall be installed and used within an

environment that provides the pollution degree max 2 and overvoltages category II in

NON HAZARDOUS LOCATIONS, indoor only. The equipment is designed to be

installed by SERVICE PERSONS only; (SERVICE PERSON is defined as a person

having the appropriate technical training and experience necessary to be aware of haz-

ards to which that person may be exposed in performing a task and of measures to min-

imize the risks to that person or other persons.)

Failure to properly install, test and maintain a CO detector may cause it to fail, res-

ulting in loss of life. Installation of the CO detector should not be used as a substitute

for proper installation, use and maintenance of fuel burning appliances, including

appropriate ventilation and exhaust systems.

This carbon monoxide detector is designed for indoor use only. Do not expose it to

rain or moisture. Do not knock or drop the detector. Do not open or tamper with the

detector as this could cause malfunction. The detector will not protect against the risk

of carbon monoxide poisoning if not properly installed.

CAUTION: This device will only indicate the presence of carbon monoxide gas at the

sensor. Carbon monoxide gas may be present in other areas. This carbon monoxide

alarming device is designed to detect carbon monoxide gas from ANY source of

combustion. It is NOT designed to detect smoke, fire or other gases unless the product

has been investigated and determined to comply with applicable requirements.

WARNING! To comply with FCC and ISED Canada RF exposure compliance

requirements, the device should be located at a distance of at least 20 cm from all per-

sons during normal operation. The antennas used for this product must not be co- loc-

ated or operated in conjunction with any other antenna or transmitter.

Figure 1: Wireless CO Detector

Legend

A. Alarm LED (see Table 1 for LED indications)

B. Tamper release opening

C. Test/Hush button

D. Battery compartment

E. Breakaway tab (see Figure 3)

PG9933 (915MHz) Wireless Carbon Monoxide Detector

Installation and Operating Instructions

ATTENTION: Read these instructions thoroughly before installation and use of the PG9933. Keep the instructions for future reference.

D-307065

Installation Instructions

Battery Installation

To replace the battery:

1. Remove the detector from its mounting base by twisting it counterclockwise.

Remove and dispose of the battery according to your local regulations.

2. To ensure proper power-down sequence, wait a minimum of 20 seconds before

installing the new battery.

3. Install a new, 3-volt CR123A Panasonic lithium battery in the battery com-

partment observing correct polarity. If the battery is incorrectly inserted, remove

gently with a flathead screwdriver and correctly reinsert.

4. Reinstall the detector onto the mounting bracket by turning it clockwise.

5. After the power-up sequence, the green LED blinks once every 12 seconds to

indicate normal operation. If the battery is not installed correctly, the detector

will not operate and the battery may be damaged.

Enrollment

The 7- digit serial number located on the back of the CO detector housing must be

enrolled on the alarm systems control panel. See the Receiver Installation Manual and

follow the enrollment procedure. For placement tests remove the detector from its

backplate for one second (tamper) and then reattach. Wait at least 30 seconds for the

test result before activating again.

A general description of the procedure is provided in the following flow chart:

Step Procedure

1 See the Installation Manual for the alarm system that the device is being

enrolled on to ensure that the proper steps are used.

2 Enter the Device Enrollment option through the specified method and select the

appropriate option to add the new device.

3 Enroll the device by inserting the batteries to power up the device and enter the

Device ID. For example, ID No. 222-XXXX.

4 Select the desired Zone Number.

5 Configure any device parameters that are required. Enter the DEV

SETTINGS menu and select the required options to configure the detector.

6 Mount and test the detector. See Testing the CO detector for information on

testing the device. In addition, see the alarm systems Installation Manual that

the device is enrolled on for other test procedures that are required.

Selecting a Location

Selecting a suitable location is critical for the CO detector. The Consumer Product

Safety Commission (CPSC) recommends to use at least one CO detector per house-

hold, located as near as possible to sleeping areas of the home, because the human

body is most vulnerable to the effects of CO gas during sleeping hours.

NOTE: Alarm shall be heard from all sleeping areas.

Figure 2: CO Detector Placement

Legend

A: Bedroom

B: Living Room

C: Kitchen

D: Basement

E: Garage

For added protection, install additional CO detectors in every bedroom and on every

level of your home. If your bedroom hallway is longer than 14 meters (40 feet), install

a CO detector at BOTH ends of the hallway. Install an additional detector 6 meters

(20 feet) away from the furnace or fuel burning heat source. For maximum protection,

the detector should also be located outside primary sleeping areas or at each level of

your home. Mount the detector on a firm wall or ceiling.

DO NOT install CO detectors:

lIn locations where the normal ambient temperature is below 40 ºF (4.4 ºC) or

exceeds 100 ºF (37.8 ºC), unless the device has been found acceptable for install-

ation at a higher or lower ambient temperature..

lIn locations where humidity is below 10% or above 93% RH non-condensing.

lNear paint thinner fumes.

lNear air conditioners, furnaces, stoves, fireplaces and any other ventilation source

that may interfere with CO gas entering the detector.

lIn locations where furniture or draperies may obstruct the air flow.

lIn exhaust streams from gas engines, vents, flues or chimneys.

lWhere dirt or dust could collect and block the sensor and prevent it from working.

lIn locations that can be reached by children.

lIn turbulent air from ceiling fans.

lIn close proximity to an automobile exhaust pipe - this will damage the detector.

Mounting

The detector can be mounted on a wall or ceiling.

The CO detector must be mounted with its bracket (when it is attached to its bracket

the tamper switch is pressed and the detector automatic reset is performed).

1. Refer to Figure 3 and install using screw locations as required. Maneuver the

mounting bracket so the screws are at the elbow of the screw slots and secure.

2. Fit the detector inside the mounting bracket by aligning it as shown in Figure 3

(detector’s alignment notch should be slightly offset from the mounting bracket

tamper release tab), then turn the detector in a clockwise direction until it clicks

into place.

3. Test the detector after completing the installation (as described in the Testing the

Detector section of this manual) and refer to the alarm control panel installation

manual for additional information concerning the use of wireless devices.

Figure 3: Mounting the Detector

Tamper Protection

The PG9933 includes a tamper resistant feature that prevents removal from the mount-

ing bracket without the use of a tool. To engage the tamper resistant feature, cut the

small breakaway tab (marked E in Figure 3) located on the mounting bracket and then

install the detector. To remove the detector from the mounting bracket once it has been

made tamper resistant, insert an appropriate tool into the tamper release opening loc-

ated on the detector housing (marked B in Figure 1). Press and hold while sim-

ultaneously turning the detector counterclockwise.

Owner's Instructions

Testing the CO Detector

NOTE: Performing a CO detector system test will generate an alarm trans-

mission. Notify the central station before testing.

Perform a CO detector system test by pressing the Test/Hush button for a minimum of

6 seconds, the red LED flashes and the sounder emits a temporal 4 pattern.

Perform a CO detector local test by pressing the Test/Hush button for a minimum of 2

seconds, the sounder will emit 2 short beeps.

NOTE: The Test button does not function when the detector is in low battery con-

dition.

Maintenance

Test the detector weekly to ensure proper operation of the detector. When low battery

is indicated (see Table 1 and Specifications) immediately replace the battery. Once a

month, use a vacuum cleaner to keep the air vents free of dust.

Go-No-Go Test

This test will set the system into alarm when carbon monoxide is sprayed onto the unit.

The procedure is as follows:

1. Press the TEST button until 2 chirps are heard.

2. Spray CO gas (use Solo C6 CODetector Tester).

3. If CO is detected, temporal 4 is sounded for approximately 30 seconds.

NOTE: Go-No-Go test does not fucntion when the detector is in low battery condition.

Product specificaties

Merk:	DSC
Categorie:	Rookmelder
Model:	PG9933
Kleur van het product:	Wit
Breedte:	125.3 mm
Diepte:	125.3 mm
Hoogte:	48 mm
Type stroombron:	Batterij/Accu
Certificering:	FCC / IC, UL / ULC, CSFM, CNC
Bedrijfstemperatuur (T-T):	4.4 - 37.8 °C
Type batterij:	CR123A
Back-upbatterij:	Ja
Gedetecteerde typen gas:	Koolstofmonoxide (CO)