Dri Eaz Velo Handleiding

Dri Eaz Heater Velo

Lees hieronder de 📖 handleiding in het Nederlandse voor Dri Eaz Velo (9 pagina's) in de categorie Heater. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/9
109042H 1 Legend Brands, Inc.
Owner’s Manual
Velo® & Velo® Pro Low Profile Airmover
LEGEND BRANDS, INC.
15180 Josh Wilson Road, Burlington, WA 98233, USA
Phone: 932 7950+1 800- - - -3030 Fax: +1 360 757 LegendBrandsRestoration.com
The Velo and Velo Pro use a patented housing design to Airmovers produce concentrated, broad-path airflow to accelerate
the evaporation of moisture from materials for drying.
Patents: http://www.LBpatents.com
R E A D A N D U N D E R S T A N D T H E S E I N S T R U C T I O N S
WARNING! To reduce the risk of fire or
electric shock, do not use this fan with
any solid state speed control device.-
WARNING! Unit must be grounded. Do
not use with an extension cord. Connect only to an outlet
provided with a ground fault interrupting device.
WARNING! Never operate a unit with a damaged power
cord, as this may lead to electrical or fire hazards. If power
cord is damaged, it must be replaced by a cord of the
same type and amperage rating.
WARNING! Do not touch grills when unit is operating.
WARNING! Do not allow children to play with or around
the unit. Be sure the unit is inaccessible to children when
not attended.
WARNING! Always operate the unit on a stable, level
surface so it cannot fall and cause injury.
WARNING! Do not operate any fan with a damaged cord
or plug. Discard fan or return to an authorized service
facility for examination and/or repair.
WARNING! Do not run cord under carpeting. Do not cover
cord with throw rugs, runners, or similar coverings. Do not
route cord under furniture or appliances. Arrange cord
away from traffic area to avoid creating a trip hazard.
NOTICE: Keep motor dry. For indoor use only.
NOTICE: Unplug when not in use or when moving unit.
NOTICE: Do not alter or modify your Velo in any way. Use
only replacement parts authorized by Legend Brands, Inc.
Modifications or use of unapproved parts could create a
hazard and will void your warranty. Contact your
authorized Dri-Eaz distributor for assistance.
BEFORE YOU BEGIN
Warranty registration
Please visit warranty.legendbrandsrestoration.com to
register your purchase. If you determine service is
Fig. B: Operating Positions
Horizontal
(for horizontal surfaces)
Vertical
(for walls and ceilings)
Right edge
(for wall drying)
Left edge
(for wall drying)
With stand for stairwells and
wall drying (Pro only)
Rear cord wrap under
bottom edge. Wrap cord
in either direction and
secure with plug clip.
with amp readout (Pro
only).
Stand folds out
and locks (Pro
only).
Inlet grill. Keep clear
of obstructions.
Outlet grill. Keep
clear of obstructions.
On/Off and circuit breaker
reset switches.
GFCI-protected
power outlet sockets
with reset switch.
Fig. A: Parts Identification
109042H 2 Legend Brands, Inc.
required, have your equipment model, serial number and
original proof of purchase available and call your
distributor for assistance with obtaining a return material
authorization (RMA).
OPERATING INSTRUCTIONS
Note that the Velo can be placed in a variety of positions
for drying and air circulation. See Fig. B for details.
1. Unwrap the cord and plug the unit into a standard
115V protected -GFCI outlet. C Be sure AUTION:
switch is in the off position connecting unit to before
power outlet.
2. Velo surface Direct the outlet toward the to be dried.
TIP: On the Velo Pro, the airflow may be adjusted by
pressing the Up or Down arrow on the speed control (Fig.
D). A digital readout shows the approximate amp draw.
Use this value to maximize the number of Velo you can s
place on a single circuit.
3. the When surface dry to the touch, switch is unit off
and next areareposition the unit in the to be dried.
4. When finished, unplug the unit and re wrap the cord- in
the cord wrap.
For additional instructions about the use of airmovers for
restorative drying, see Tech Tips under Resources on
www.LegendBrandsRestoration.com.
Electrical safety devices
Circuit breaker: If the circuit breaker detects overload or
short circuit conditions, the breaker will automatically shut
off the electrical supply. If this occurs, check the power
cable carefully for any damage and ensure it is plugged
into a properly grounded outlet. Press the Circuit Breaker
Reset Switch (Fig. A) to reestablish the electrical supply.
G F C I :round ault ircuit nterrupter If the GFCI device
detects a ground fault, will automatically shut off the it
electrical supply. If this should occur, check the power
cable carefully for damage and ensure it is plugged into a
properly grounded outlet. Press the GFCI reset button
(Fig. A) to reestablish the electrical supply.
TRANSPORT AND STORAGE
Always use the handle to load or carry the unit.
Wrap cord in Cord Wrap tab either direction under front
and rear snug and secure bottom edge (Fig. A). Pull cord
with plug clip.
Units may be stacked for transport and storage.
When transporting in a vehicle, secure the unit(s) carefully
to prevent sliding and damage to the unit and/or injury to
vehicle occupants.
Keep unit dry. Do no expose the unit to rain or snow. t
MAINTENANCE
WARNING: Unplug unit before performing any
maintenance.
Before each use
Inspect the power cord. If cord is damaged, do not use.
Always grasp the plug (not the cord) to unplug.
As needed
The exterior may be cleaned with a mild solution of
detergent. Ensure housing is completely dry before use.
To clean interior, see Fig. C for instructions.
FOR SERVICE CALL YOUR LOCAL DISTRIBUTOR or
the Legend Brands Service Department at
800 932 3030- - .
Be sure to visit warranty.legendbrandsrestoration.com to
register your purchase. Your registration will help us
provide you with updated product information as needed.
WARNING: This product and other substances
that may become airborne from its use contain
chemicals, including lead, known to the State of California
to cause cancer, birth defects, or other reproductive harm.
For more information, go to P65Warnings.ca.gov
Fig. C: Disassembly
Fig. D ( Pro only)
Variable speed control with amp and total unit hours
display
To disassemble for cleaning:
1. Lay the unit on its top
(upside down). Remove the 4
blower bolts from the bottom
of the unit.
2. Turn the unit right side up
and remove the 14 screws
around the perimeter of the top
housing and electrical
enclosure.
3. Open the electrical box and
feed the blow cord back er
through the opening to create
slack inside the housing.
4. Lift the top housing shell
and electrical enclosure
together and flip them over
next to the base to expose the
inside of the housing.
5. Lift the blower out for full
access to the inside of the
housing.
6. Reverse the steps for
reassembly. IMPORTANT: Be
sure to pull any slack blower
cord back into the electrical
enclosure before the lid is
placed on the electrical
enclosure.
109042H 3 Legend Brands, Inc.
SPECIFICATIONS
Model Velo Speed 2- Velo Pro
Weight 8.8 19.3 lbs. | kg 21.2 lbs. | 9.6 kg
Dimensions
(D × W × H)
24 × 18 × 9 in.
61 × 45.7 × 22.9 cm
24 × 18 × 9 in.
61 × 45.7 × 22.9 cm
Amp draw (115V)
1.7 amps (low)
2.1 amps (high)
1.2–1.9 amps
Velos per
15 amp circuit
Up to 7 Up to 10
Power
190.0W (low)
241.5W (high)
185W
Air movement
511 CFM (low)
885 CFM (high)
500–885 CFM
850 1504 – CMH
Static pressure
1.28 in.(low)
1.7 in. (high)
1.65 in. (H2O)
Sound level (avg.)
59.9 dB (low)
71.5 dB (high))
69 dB
Control
Two speed rocker
switch
On/Off switch with
variable speed
Cord length
18 ft. | 5.5 m
18 ft. | 5.5 m
Fan 6 blades 6 blades
Construction
Injection molded
housing; steel wire
inlet and outlet grills .
Injection molded
housing; steel wire
inlet and outlet grills.
Safety ETL tested to UL and
CSA standards
ETL tested to UL and
CSA standards
Specifications are subject to change without notice. Some values
may be approximate.

Product specificaties

Merk: Dri Eaz
Categorie: Heater
Model: Velo

Heb je hulp nodig?

Als je hulp nodig hebt met Dri Eaz Velo stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Heater Dri Eaz

Dri Eaz

Dri Eaz Velo F518 Handleiding

12 Augustus 2023
Dri Eaz

Dri Eaz Velo Pro Handleiding

5 Juli 2023
Dri Eaz

Dri Eaz Stealth AV3000 Handleiding

28 Juni 2023
Dri Eaz

Dri Eaz Vortex Handleiding

25 Juni 2023
Dri Eaz

Dri Eaz DriForce Handleiding

24 Juni 2023
Dri Eaz

Dri Eaz Dri-Pod Handleiding

23 Juni 2023
Dri Eaz

Dri Eaz Velo Handleiding

22 Juni 2023

Handleiding Heater

Nieuwste handleidingen voor Heater

Harvia

Harvia Forte AFB9 Handleiding

15 November 2024
Dimplex

Dimplex DTD4T Handleiding

15 November 2024
Dimplex

Dimplex DX 425E Handleiding

15 November 2024
Dimplex

Dimplex Mini Cube Handleiding

15 November 2024
Perel

Perel 120-1 Handleiding

14 November 2024
Perel

Perel TC78071 Handleiding

14 November 2024
Perel

Perel IH0003 Handleiding

14 November 2024
MSW

MSW -CDAIR-120S Handleiding

13 November 2024
Uniprodo

Uniprodo UNI_EH_03 Handleiding

13 November 2024
Heinner

Heinner HOH-YD11WH Handleiding

13 November 2024