Draper Cinefold Handleiding

Draper Projectiescherm Cinefold

Lees hieronder de 📖 handleiding in het Nederlandse voor Draper Cinefold (2 pagina's) in de categorie Projectiescherm. Deze handleiding was nuttig voor 41 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Assembly Instructions

Cinefold Portable Projection Screen by Draper

Frame Hinges and

hinge locks

Handy

Crank

Viewing

Surface

Adjustment

Knob

2" Min.

44" Max.

Anti-sway stabilizers

optional with HD legs

Standard

T-Leg

Frame

Snaps

Handy Crank Viewing

Surface

Bottom row of snap

studs to accept skirt

Standard T-Leg

Heavy duty legs optional

Frame/Screen Assembly

① Open carrying case and remove pouch containing screen surface, and

three aluminum assemblies. The largest package is the frame. Unwrap and

unfold it completely in one direction only, locking all hinges. Frame should

lie with snaps facing up.

② Remove surface from its envelope. With male snaps at bottom, snap

surface to frame. For easier surface attachment, start in one corner, then

work your way around the frame. Make sure snaps are secure.

Please note: For steps 3-5, screen should remain on ﬂ oor or table, with

surface facing up. Carefully lift screen from ﬂ oor or table to complete each

step.

③ Lock corner braces.

④ Unfold leg assemblies and lock hinges. Check that ad just ment knob is in

the hole desired (upper for vertical screen position, lower for keystone

elimination). DO NOT unfold feet at this time.

⑤ Attach legs to back side of vertical frame sections, as indicated by the

color coded markings, using Handy Cranks. For standard screen height,

match colored tapes exactly. Height is adjustable in 6" increments.

⑥ Raise Cinefold to a vertical position and unfold feet. Tighten ad just ment

knobs to maintain legs at desired angle. If your screen includes Heavy-

Duty Legs, unfold and lock the extensions on the backs of the feet, hinge

up to the backs of the leg, and attach with Handy Crank.

⑦ If Anti-Sway stabilizers are supplied with your screen, refer to illustration

and attach with Handy Cranks.

A Note About Surfaces

① Always fold with snaps face-to-face. Do not permit screen fabric to

contact border material or snaps when folded. Store in pouch

provided.

② Take care at all times not to permit Cinefold viewing surface to contact any

dusty or dirty area, nor any varnished or painted object.

③ When necessary, clean Cinefold viewing surface with soap and water. mild

USE NO SOLVENTS! Surface must be completely dry before folding.

Caution

① Read instructions through completely before proceeding; retain for future

reference.

② Handle viewing surface with care; do not allow it to come in contact with

sharp or dirty objects.

③ Use Handy Cranks provided; failure to do so may lead to screen damage.

④ Make sure screen is level.

⑤ Do not write on viewing surface.

⑥ The ideal temperature range for assembling folding screens to prevent

damaging the surface is 68°-78° F (20°-26° C). Assembling below

recommended temperatures may damage surface and void warranty.

Caution: Beware

of pinch points.

Caution: Make sure all hinges and joints are locked

before raising screen to standing position.

Caution: Make sure screen

is placed on level surface.

Assembly Instructions

Truss-Style Cinefold Portable Projection Screen by Draper

Truss Assembly

① Remove pouch containing viewing surface from case and set aside.

Remove all aluminum assemblies.

② Unfold all folded aluminum assemblies completely, noting labels and

color-coded marks. Lock all hinges. Position Stage Right and Stage Left

sections in appropriate positions with snaps facing . Top and Bottom up

sections should be set with snaps facing .down

③ To increase frame rigidity, hinges on top and bottom frame sections have

rivnuts marked with red and green. Insert a Handy Crank through the

threadless rivnut (red) and tighten into the threaded rivnut (green).

④ Apply small sections marked “Stiffener Bars” to back of Bottom frame

section, using eight Handy Cranks each. Failure to use all Handy Cranks

may result in damage to screen frame. Turn Bottom frame section over so

snaps face up.

⑤ If your screen frame is less than 25' wide, repeat step 4 for Top frame sec-

tion. Frames 25' wide and over are equipped with a special full-width Stiff-

ener for the top frame section. To attach it, place Stiffener ﬂ at with green

rivnuts face down. Place top frame section on top of and at right angles

to Stiffener, over the green rivnuts. Insert and tighten standard Handy

Cranks. Install 45° angle braces to the Top frame section and Stiffener with

short Handy Cranks. Turn Top frame so snaps face up.

Dress-Up Kit Assembly

PLEASE NOTE: All components are labeled and color coded to

facilitate assembly.

A. Valance Bar attaches to frame with simple bayonet-style mounting.

B. Draper Bars mount to Valance Bar, bayonet-style.

C. Optional adjustable Skirt Bar is secured to frame at desired level with

positive-locking plunger mechanism. If Skirt Bar is not used, Skirt may

be snapped to bottom of viewing surface.

D. Valance, Drapes, and Skirt snap onto Mounting Bars.

E. Gaps between the frame and the valance can be easily removed by

pulling the bottom edge of the valance to close the gap.

F. Pulling and smoothing the edges of the panels will remove any

wrinkles or puckers that might be present when product is unfolded.

Drapery

Bar

Valance Bar

Drapery

Bar

Adjustable Skirt Bar

Rigid

Truss

Frame

Anti-Sway

Stabilizers

Heavy-Duty

Legs

Frame & Legs

Assemble with

Handy Cranks

Handy Crank

⑥ Join Top and Bottom to Stage Right and Stage Left, using two Handy

Cranks on each of the four corners. Match numbers on white labels, and

keep in mind that no Handy Crank should protrude outside screen frame.

⑦ Remove surface from pouch. With the row of male snaps at bottom, posi-

tion screen surface over frame. Snap each of the four corners, then snap

across bottom, up sides, and across top.

⑧ Attach feet to inner side of legs with Handy Cranks, matching color-coded

markings. Attach legs to Stage Right and Stage Left with Handy Cranks,

matching colored tapes.

⑨ Raise screen to a vertical position. Add Heavy-Duty Legs and Anti-Sway

Stabilizers with Handy Cranks in the positions indicated below.