Draper Silhouette/Series M Handleiding

Draper Projectiescherm Silhouette/Series M

Lees hieronder de 📖 handleiding in het Nederlandse voor Draper Silhouette/Series M (2 pagina's) in de categorie Projectiescherm. Deze handleiding was nuttig voor 47 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Your Draper screen can be mounted on a wall or suspended from the ceil ing,

or mounted on special 6" extension bracket. Extension brackets must be

ordered separately from Draper. With each method of installation, the case

must be mounted level and with the ﬂ at back parallel to the wall.

To reduce the risk of personal injury, use only the hardware which comes

with the screen or is speciﬁ ed in these instructions.

The screen (or extension brackets) should be mounted into studs or block ing

in the wall/ceiling, or in drywall (minimum thickness

1/2") with speciﬁ ed anchors.

For any other type of installation, follow all local build ing and safety codes.

Steel studs, concrete or cinder block walls and all other types of non-wood

frame construction require the use of special screws or anchors. The se-

lec tion of ap pro pri ate mounting hardware should be made by a qualiﬁ ed

pro fes sion al installer.

When locating viewing surface and checking clearance for screen’s op er a tion,

remember surface is centered in case. Handle case carefully to avoid scratch-

ing. Regardless of mounting method, screen should be positively and securely

supported so that vibration or even abusive pulling on the viewing surface

will not cause case to work loose or fall. Installer must insure that fasteners

used are of adequate strength and suitable for the mounting surface.

Wall Mounting

Mount 2, 3, or 4 aluminum brackets provided (“Z” Clips) on the wall at

desired height, using appropriate fasteners. Verify that they are in line and

level to fully engage with the mounting lip on back of screen case. 1

5/8" of

free space is required above the “Z” Clips to allow case lip to be engaged

over the lip of the “Z” Clips.

Engage the lip on back of screen case with lip of “Z” Clip and gently pull

down to fully engage case to brackets.

Ceiling/Suspended Mounting

Locate two offset ceiling brackets (supplied) and slide these into the chan-

nel on top of screen case by aligning the chamfered edges of each bracket

parallel to the channel length. Allow bracket to drop against bottom of

channel and then rotate bracket counter-clockwise. Slide one bracket to

each end of screen case until it stops against end cap of case. Tighten two

set screws to lock bracket in place. Make sure that the ﬂ ange of the ceiling

bracket that has four holes is extended beyond the end caps of the case.

Repeat above procedure for second ceiling bracket, making sure to slide it

towards opposite end of case.

To mount against ceiling, hold screen case against ceiling and mark

mounting hole locations. Each brack et has 2 holes towards the front edge

and 2 holes towards the back edge. Installer must use at least 2 fasteners

per bracket with one fastener in one of the two holes clos est to back edge

of bracket, and one fas ten er in one of the two holes closest to front edge of

bracket. Installer must insure that fasteners are of adequate strength and

suitable for the mounting surface chosen.

To mount suspended from ceiling, the brackets need to be installed on

screen case as noted above. Attach “S” Hooks (supplied) through the holes

in the brackets. Select the set of holes that allows the screen to hang in a

vertical position. The installer is to provide the materials and fasteners to

attach the “S” Hooks to the ceiling. Installer must insure that the fasteners

and suspension material are of adequate strength and suitable for the

mounting surface chosen.

Ceiling racket in b

channel of case

Ceiling racketb

Mo nting fastenersu

(s pplied y others, 2 per racket)u b b

(front of Silho ette case)u

(right end of Silho ette case)u

Installation/Operating Instructions

Silhouette/Series M and C

Manually Operated Projection Screens by Draper

Lip on back

of case

"Z" Clip

(wall mounting bracket

supplied with Silhouette)

Silho ette f lly engaged u u

on "Z" Clip

Caution

➀

Read instructions through completely before proceeding; keep

them for future reference. Follow instructions carefully. Installation

con trary to instructions invalidates warranty. Care in both mount-

ing and correct operation willl assure long and sat is fac to ry service

from your Draper screen.

➁

Screen should be accessible for complete removal should fabric

become damaged or for service if required.

➂

Screen should be installed level (using a carpenter’s level).

➃

Nothing should be fastened to screen dowel or viewing surface.

➄

Operating crank for Series C is packed separately in screen car-

ton. Do not discard with packing material.

Note: Screen has been thoroughly inspected and tested at fac-

tory and found to be operating properly prior to shipment.

Installation

If you encounter any difﬁ culties installing or servicing your

screen, call your dealer or Draper, Inc., Spiceland, Indiana, (765)

987-7999, or fax (765) 987-7142.

Extension Wall Brackets

6" or 10"-14" Extension Wall Brackets are needed to mount Silhouette

ex tend ed from wall. Wall Brackets are not supplied with screen and must be

ordered separately. Specify “Silhouette Extension Wall Brackets”.

① Mount the Wall Brackets to the wall, making sure they are level and verti-

cally plumb. Installer must insure fasteners (not included) are of adequate

strength and suitable for chosen mounting surface.

② Attach hanging bracket to wall bracket as shown.

③ Attach (1) “Z” Clip and (1) Support Plate (supplied with screen) to hanging

bracket as shown.

④ Engage the lip on back of screen case with lip of “Z” Clip and gently pull

down to fully engage case to brackets.

⑤ Install hook bracket as shown making sure the two tabs of this bracket

hook over the case extrusion.

⑥ Install #10-24 hex head screw through hook bracket, hanging bracket, and

support plate as shown.

Operating Instructions—Series M Standard

To lower picture sur face, pull screen down to de sired position. Hes i tate—then

allow screen to slightly retract very slowly until it locks in place.

To raise picture surface, pull down on the pull bail, then raise quickly, as a window

shade. Keep control of the picture sur face. Do not allow it to roll un con trolled

into the case, or dam age is sure to result.

Operating Instructions—Series M with AutoReturn

To lower picture surface, pull screen down. —then allow screen to Hesitate

retract very slowly until it locks in place.

To raise picture surface, pull screen down gently until it stops, then release.

Operating Instructions— Series C

To lower screen sur face, attach the crank handle to the “U” joint stud located on

the left hand side of the screen. With the crank handle in its operating position,

rotate coun ter clock wise. An internal pin within the gear box will stop the screen

when fully extended. The crank handle can be removed if desired. The shipping

support brackets must be removed from each end of dowel during initial operation.

To raise screen surface, attach the crank handle to the “U” joint stud located on

the left hand side of the screen. With the crank handle in its operating position,

rotate in a clockwise direction. An internal pin within the roller will stop the screen

when fully retracted. The crank handle can be removed if desired.

Removing Case Fascia

Caution: When removing or reattaching fascia, do not handle fascia by

unpainted ends.

Case fascia is removable to access roller assembly. To remove fascia, depress

outward the spring lip located inside lower front corner of screen case and pull

lower corner of fascia outward. Repeat this at right end of case. Support fascia

from center and rotate lower front edge upward ap prox i mate ly 40° to disengage

the Roll-Lok hinge at the top front of screen case. Fascia can now be completely

removed from case.

To install fascia, generally reverse instructions above making sure the Roll-Lok

hinge is completely engaged before rotating fascia down towards the closed

position. Depress spring clips outward, push lower corners of fascia inward until

lips of spring clips hook behind fascia.

Please Note: Be sure the clips are completely up against the ends of the

fascia.

Silhouette/Series M and Series C by Draper

Page 2 of 2

1½" Viewing Surface

23/ "8

21/ "8

4¾"

Case Dimensions

Silhouette/Series M

Silhouette/Series C

Tab-Tension Adjustment Procedure for Silhouette/Series C

➀ Determine which side requires adjustment.

➁ Secure dowel with one hand.

Caution: Do not touch or bend surface.

➂ Using Philips-head screwdriver,

depress spring-loaded adjustment

screw (see drawing) and slowly turn

clockwise to tighten tension, or

counterclockwise to loosen tension.

The screw adjusts in ¼ turn

increments. Adjust only

(¼ turn).one increment

➃ If problem is not corrected, leave

screen in position for 24 hours to allow

surface material to stretch into position.

➄ If problem still is not corrected, repeat steps

➁

and

➂

Do elwAdj stmentu

Screw

Tensioning

Ca leb

www.draperinc.com (765) 987-799

Viewing Surface

Silhouette/Series M with Auto Return

Hook

Bracket

CB ¼"-20 x 1¾" Z Keg,

Flat Washer,

¼"-20 Nylock Nut

#10-24 x 7/8"

Phillips Pan Head

Screw, Nylock Nut

#10-24 x ½"

Hex Head Screw

Z Clip

Wall

Bracket

Support

Plate

Hanging

Bracket

Product specificaties

Merk:	Draper
Categorie:	Projectiescherm
Model:	Silhouette/Series M
Gewicht:	18597 g
Oorspronkelijke beeldverhouding:	16:9
Montagewijze:	Muur
Kleur behuizing:	Wit
Kijkhoek:	60 °
Zichtbare schermhoogte (h):	2311 mm
Zichtbare schermbreedte (b):	1549 mm
Diagonaal:	100 "
Type aandrijving:	Handmatig
Totale grootte van het scherm (hoogte x breedte):	124 x 220 cm
Formaat:	HDTV
Schermgain:	1
Case L1:	2413 mm