Draper Paragon E Handleiding

Draper Projectiescherm Paragon E

Lees hieronder de 📖 handleiding in het Nederlandse voor Draper Paragon E (3 pagina's) in de categorie Projectiescherm. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

Caution

1 Read instructions through completely before proceeding.

2 Follow instructions carefully. Installation contrary to instructions invalidates

warranty.

3 Pick up screen case from ends only. Picking case up at other points will

damage case may damage fabricand .

4 To insure a safe installation, the of the unit MUST BE entire weight

supported by the end-plates.

5 Entire bottom of screen case should be unobstructed to permit access to

bottom panel for making electrical connections or servicing.

6 Screen should be installed level (using a carpenter’s level).

7 Operating switch(es) packed separately in screen carton. Do not discard

with packing material.

8 Screen operates on 220V AC, 50 Hz., 1ph. current.

NOTE: Screen has been thoroughly inspected and tested at factory and found to

be operating properly prior to shipment.

Mounting Screen

Regardless of mounting method used, the following points apply:

1 Screen should be lifted into position only by the end mounting brackets.

Keep case level by lifting end plates simultaneously to prevent surface

damage. Draper provides eyebolts to use in hoisting the screen. DO NOT

use eyebolts to mount screen. Using both mounting holes in the mounting

brackets makes for a much more stable installation. Never attempt to lift

screen along its length.

2 The entire weight MUST BE of the unit supported by the end plates to provide

a secure installation. Anchoring of the intermediate case support brackets is

typically only needed to reduce any visible case deﬂection when the unit is

mounted into a ceiling pocket or ceiling tile opening. For installations that are

not recessed, the amount of case deﬂection is usually not noticeable.

3 Screen should be positively and securely supported so that vibration or even

abusive pulling will not weaken installation.

4 Installer must insure that fasteners used are of adequate strength and suitable

for the mounting surface chosen. Installer must also insure that wall or

ceiling structure are of adequate strength. Supporting hardware (chains,

cables, rods, etc.) must be essentially vertical.

5 Entire bottom of case must be readily accessible after installation is complete.

6 Front, back and top of case must be straight—not forced to warp or bow. Use

threaded rod and support brackets to keep large cases from warping. DO NOT

use support brackets to support the weight of the screen.

7 Do not use case to support adjacent sections of ceiling.

8 If optional ceiling ﬂange trim kits are attached, use hardware provided.

9 If case is painted, slots on bottom of case should be shielded to protect viewing

surface from paint splatters or overspray.

 Do not seal unit in ceiling until electrical connections have been made and

screen has been operated successfully.

Electrical Connections

Screen operates on 220V AC, 50 Hz., 1ph. current.

Junction box is located just above the closure panel, at the motor end of screen

(left hand motor location only on Paragon). To properly remove closure panel, two

people should follow the steps on page two of these instructions. The junction

box access plate is held closed with pan head screws and may be opened with

a Phillips screwdriver. Removal of access plate exposes brown, black and blue

pigtail leads and green internal ground wire per attached wiring diagram.

Screen is shipped with internal wiring complete and control switch(es) fully boxed.

Wire connecting screen to switch(es) and switch(es) to power supply should be

furnished by installer. Connections should be made in accordance with attached

wiring diagram, and wiring should comply with national and local electrical codes.

All operating switches should be “off” before power is connected.

Please Note: Do not wire motors in parallel.

Operation

When screen is ﬁrst operated, Cycle unit down and up several times be cautious!

to conﬁrm satisfactory operation.

220V AC Single Station Control—3-position up-off-down switch permits

operation to be stopped at any point. Factory adjusted limit switches automatically

stop screen when fully down or fully up.

220V AC Multiple Station Control (Not CE approved) Switches are similar —

in appearance to 220 V AC Single Station Control. Screen stops when switch is

released and may be restarted in either direction. Factory adjusted limit switches

stop screen automatically when fully down or fully up.

24V Control—Three-button up-stop-down switch(es) stop at any point desired,

operate in any sequence. Factory adjusted limit switches automatically stop screen

when fully down or fully up. Installer should incorporate an all-pole disconnect in

the ﬁxed wiring.

Key Operated Switching (Not CE approved) Two kinds of key-operated —

switches are optionally available with this unit. The key-operated power supply 1

switch controls power to the screen and switches. When it is “off”, the switches

will not operate screen. Key may be removed from the switch in either “on” or “off”

position. A three-position key switch permits the screen to be operated directly 2

by key. In this case, the screen’s operator must always have a key.

RS232/Ethernet—Serial communication and network communication optionally

available with wall switches, RF or IR remote.

Adjustments

Please Note: Screen limits are factory set for optimum performance of the

screen. A procedure is outlined below for minor tweaks, but any adjustment

of these limits may negatively affect the ﬂatness of the screen surface and

could also void the warranty. Please check with Draper prior to resetting

screen limits.

CAUTION: Always be prepared to shut screen off manually when new

adjustment is being tested. Screen may be severely damaged if viewing

surface is allowed to run too far up or too far down.

CAUTION: Be sure all switches are in “off” position before adjusting limit

switches.

Caution: Rough handling in transit may cancel/reset motor limit settings.

To prevent viewing surface damage, be prepared to stop descending screen

if surface begins to retract instead of stopping or if motor does not shut off

when screen has fully retracted into case.

ADJUSTING “FULLY UP” POSITION—Put a small screw driver in the groove of

the yellow button on the motor and press vertically until hearing a "click". Raise

the screen by pressing the "up" switch on unit. Press the "stop" switch when the

screen is at the desired position. Then press the yellow button on motor until you

hear a "click", then release.

ADJUSTING “FULLY DOWN” POSITION—Put a small screw driver in the groove

of the white button on the motor and press vertically until hearing a "click". Lower

the screen by pressing the "down" switch on unit. Press the "stop" switch when the

screen is at the desired position. Then press the white button on motor until you

hear a "click", then release.

AT NO TIME SHOULD SCREEN BE UNROLLED ENOUGH TO EXPOSE ANY

PART OF SCREEN ROLLER.

Installation/Operating Instructions

220V Paragon/Series E and V Electric Screen by Draper

12"

* - Case support bra ets will be enly spaced along the caseck ev

2" 2"

2¼"

Series V

Viewing

Surface 21/8"

Series E

Viewing

Surface

Var ies

Please see back page for dimensional diagrams of case and optional wall

mounting bracket, wiring diagrams and instructions on removing and replac-

ing the bottom closure.

These Installation/Operating Instructions are available in the ofﬁcial language of

the country where you purchase the product. Please contact your distributor to

request a copy.

Vous pourriez demander les instructions d’installation et d’opération traduises

dans la langue ofﬁcielle du pays ou vous achetez le produit. Veuillez demander à

votre distributeur.

Die Gebrauchsanweisung für Installation und Konstruktion sind in der ofﬁziellen

Sprache des Landes, indem Sie das Produkt gekauft haben, vorhanden. Fragen

Sie die jeweilige Verkaufs-Abteilung.

If you encounter any difﬁculties installing or servicing your Paragon screen, call your dealer or

Draper, Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-1689.

Suitable for use

in environmen-

tal air space

in accordance

with Section

300-22(c) of the

National Electri-

cal Code, and

Sections 2-128,

12-010(3) and

12-100 of the

Canadian Elec-

trical Code, Part

1, CSA C22.1.

Caution: Do not remove the roller assembly from the case unless neces-

sary for repairs. If the roller assembly is removed, be sure motor is fully

re-seated in the bracket, and re-secure it carefully with the motor retaining

spring and screw (see diagram below).

Please note: Maximum torque for

tightening screw is 5 lb-inches.

Instructions

continued

on Page 2

US Patent No.

6,873,461

These instructions are meant as a guide only. They do not imply any responsibility

on the part of the manufacturer for improper installation or faulty workmanship at

the jobsite.

Case Dimensions*

Paragon/Series E and V 220V by Draper Page 2 of 3

83 mm

73 mm

25 mm

" (9.5 mm) dia.

" (12 mm) dia.

73 mm

Optional Wall

Mounting

Bracket

*Please Note: Optional wall brackets add 4.5 cm per bracket to case

length. Wall mounting bracket hole location is 2.54 cm from end of case.

www

.draperinc.com (765) 987-799

* * - Case support bra ets will be enly spaced along the caseck ev

51 mm

Series V

Viewing

Surface

Series E

Viewing

Surface

Varies

305 mm

337

127

203

51 mm

35 mm

No. of

Intermediate

Case Width Brackets

<244 cm 0

> 244 and < 457 cm 1

> 457 and < 610 cm 2

> 610 and < 878 cm 3

Brackets are equally spaced from each

other and each end. For example, if the

case length is 513 cm, then each of the

two brackets will be placed approxi-

mately 171 cm from each end (with 171

cm between them).

Bottom Closure Removal/Replacement

Step 2

Step 3

Step 4

Removal and replacement of the bottom closure panel requires two people

positioned about 5' from each end of the panel. Closure should be handled

as shown in Step 5 below to prevent bowing of the closure during handling.

Step 1

Screw and washer

Before removing bottom closure, you

must ﬁrst remove screws at each end

of case (see drawing at right).

Caution: Be sure to replace

screws and washers at each end

of case when replacing closure!

Tab-Tension Adjustment Procedure

Draper’s Tab-Tensioning System is factory-set, and under normal

circumstances will not require ﬁeld adjustment. If, however, you notice

wrinkles, waves or other indications that the tensioning cables need to

be adjusted, follow the procedure below.

1 Determine which side requires adjustment.

2 Secure dowel with one hand.

3 Using Phillips-head screwdriver, depress spring-loaded adjustment screw

and slowly turn CLOCKWISE TO INCREASE tension, or

COUNTER-CLOCKWISE TO RELEASE tension. The screw adjusts in

¼ turn increments. Adjust only . one increment (¼ turn) at a time

4 If problem is not corrected, leave screen in position for 24 hours to allow

surface material to stretch into position.

5 If problem still is not corrected, repeat steps 2 and 3.

Caution: Do not touch

or bend surface.

ADJUSTMENT

SCREW

TENSIONING

CABLE

DOWEL

ADJUSTMENT

SCREW

TENSIONING

CABLE

DOWEL

Step 5

Wiring Diagrams

Please Note: Do not wire motors in parallel.

Neutral

220v,

50 Hz.

Dashed wiring

by installer

Control

switch

Single Station Control

CE Approved

Junction box at

left end of screen

Internal Screen Wiring

Blue-220v (Common)

Brown-220v (D n)ow

Black-220v (Up)

Dashed wiring

by installer

Neutral

Hot

Multiple Station Control

Not CE Approved

Cap off with wire

nut & tape

Red

Blue

Black

220v, 50 Hz.

Black

Junction box at

left end of screen

Internal Screen Wiring

Blue-220v (Common)

Brown-220v (Down)

Black-220v (Up)

Green/Yellow (Motor Ground)

Paragon/Series E and V 220V by Draper Page 3 of 3

www

.draperinc.com (765) 987-799

Low Voltage and Remote Control

Dashed wi ng electricianri by

Low ltage wi ng othersvo ri by

Receiver

Button 3 Button Wall Switch

DOWN - Black

COM - White

UP - Red

all Switch

230 VAC

Line

White-Common to screen & 230V lAC Neutra

Red-to screen (directional)

Brown-to screen (directional)

Yellow-to 230V AC-Hot

Black-to 230V AC-Hot

Green/Yellow (Ground)

Blue (Common)

Black (Up)

Brown (Down)

Inter

nal Screen Wi ngri

Green/Yellow

(Motor Ground)

Electrically Straight

Data Cable to more

LVC-IV modules*

*A maximum of six (6)

LVC-IV modules can be

linked together.

GND

Location of y ke

operated 0n-off

switch if furnished.

FUSE - 3.15 AMP

250 VAC 5x20mm

IR Eye Input

Low Voltage

Trigger

3-28 VDC

RS232/485

Inputs/Outputs

Product specificaties

Merk:	Draper
Categorie:	Projectiescherm
Model:	Paragon E
Kleur van het product:	Wit
Gewicht:	376000 g
Oorspronkelijke beeldverhouding:	16:9
Kleur behuizing:	Wit
Zichtbare schermhoogte (h):	338 mm
Zichtbare schermbreedte (b):	599 mm
Diagonaal:	270 "
Totale grootte van het scherm (hoogte x breedte):	351 x 610 cm
Formaat:	HDTV
Schermgain:	1
Case L1:	6350 mm