Draper Access/V Handleiding
Draper
Projectiescherm
Access/V
Lees hieronder de 📖 handleiding in het Nederlandse voor Draper Access/V (8 pagina's) in de categorie Projectiescherm. Deze handleiding was nuttig voor 68 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/8
Contents
Overview - Components .......................................................................................1
Section 1 - Removing Shipping Brackets
(Tab-Tensioned, "V" Surfaces only)
.......2
PLEASE READ - Safety Information ....................................................................2
Section 2 - Hanging Screen .................................................................................3
Section 3 - Bottom Access FIT Panel Installation/Removal ..........................3
Section 4 - Motorized Roller/Fabric Installation ..............................................4
Section 5 - Motorized Roller/Fabric Removal ...................................................4
Section 6 - Operation............................................................................................5
Section 7 - Tab-Tension Adjustment Procedure ..............................................5
Section 8 - Limit Adjustments .............................................................................6
Section 9 - Case Length Dimensions ................................................................. 7
Section 10 - Case Width Dimensions .................................................................7
Section 11 - Mounting Bracket Dimensions......................................................7
Section 10 - Wiring Diagrams: 110-120V Motor and Quiet Motor ..................8
Overview - Components
CAUTION
Read and understand all warnings
(Page 2)
before beginning installation.
Electrical
Cutout
Tab Tensioning
“V” Dowel
“E” Dowel
Mounting Bracket
Mounting Bracket Hoisting Bracket
Leveling Brackets
Hoisting Bracket
“E” Free Hanging
Viewing Surface
“V” Flexible Vinyl
Viewing Surface
Trim Flange
Shipping Brackets Attached
to Dowel and Screen Case
(V Screens Only)
Please Note: Shipping brackets must remain
in place until product has been mounted and
connected to power
(see Sections 1 and 4 in this
document.)
.
Also, DO NOT operate screen before removing
shipping brackets from screen case.
TOOLS REQUIRED
POW R RILE D L
PENCIL
TAP ASUE E M RE
HAR ARDW E
(b oth rs)y e
L LEVE
Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385
draperinc.com | 765.987.7999 | 800.238.7999
© 2020 All Rights Reserved | FORM: AccessFit_Inst20
Access FIT E and V
Electric projection screen
INSTRUCTIONS
INSTALLATION & OPERATION
If you have any difficulties installing or servicing your
Access FIT screen, call your dealer or Draper, Inc.
PLEASE READ - Safety Information
WARNING
Improper installation and use of the Access Fit E and V screen can result in serious injury or death. Primarily, injuries can occur if the unit falls due to
imprecise installation, mishandling of the unit during installation, or installation on an insufficient wall or ceiling structure. Please use extreme care.
1.
Please read the following installation guidelines thoroughly and follow them
carefully. Failure to do so may cause product to fall or otherwise fail, and could
result in serious injury.
2.
Installation and calibration of the unit should only be performed by an
authorized, qualified, and experienced professional. In particular, electrical
work and wiring [indicated in diagram by dashed lines] must be completed only
by a qualified professional electrician who has read this manual completely
and is familiar with the construction and operation of this equipment and the
hazards involved.
3.
Do not affix the unit to walls or ceilings that have inadequate strength
to permanently hold the unit during use. It is the owner’s and installer’s
responsibility to confirm the wall or ceiling to which the unit attaches is
sufficient to permanently hold the weight and stress loads of the unit at all
times. Draper, Inc., is not responsible for improper installation, application,
testing, or workmanship related to the product at place of installation.
4.
It is the installer’s responsibility to make sure appropriate fasteners are used
for mounting.
5.
All hardware must be installed level. Unit must be level and square.
6.
Never leave the area while operating the unit during installation, maintenance,
or normal operation, unless it is secure and safe.
7.
Before testing or operation, carefully inspect the entire area and path
(especially
underneath)
of unit to be sure no persons or objects are in the area.
8.
Turn off power and any nearby equipment or cables carrying electricity before
connecting switches, wires, controls, or electrical components.
9.
Do not wire motors in parallel without written permission from Draper, Inc.
10.
During testing or operation, carefully watch the surrounding area for any
potential safety concerns including nearby persons or objects.
11.
After installation, the entire system, including all sensors, should be carefully
tested to ensure safe and normal operation. Extreme care should be taken
during testing to remain clear of moving parts to avoid possible injury.
12.
Operation of unit should be performed only by authorized and qualified
personnel, who have been trained in its safe and effective operation and
understand its safety features.
13.
The safety features of the unit should never be disabled, bypassed, or
overridden. The system should not be operated until all safety features are
properly and completely installed, calibrated, and tested.
14.
Unit may need to comply with local, state, or district rules and regulations, in
particular when installed in schools. All applicable rules and regulations should
be reviewed before installation and use.
15.
Failure to precisely follow installation guidelines invalidates all
warranties.
16.
Custom products/installations may not be reflected in this manual. Call Draper,
Inc., if you have questions about the installation of custom products or any
questions about your installation.
Before Beginning Installation
1.
Look for any job site conditions that could interfere with installation or
operation of the system.
2.
Read carefully and be sure to understand all installation instructions and
all related operations manuals. These instructions are intended to serve
as a guide for the installer and owner. They should be followed closely and
combined with the expertise of experienced qualified installers. Draper, Inc., is
not responsible for improper installation, application, testing, or workmanship
related to the product at place of installation. Please retain all instructions for
future use.
3.
Open cartons lengthwise.
4.
Locate and lay out all pieces.
5.
Inspect all boxes to make sure you have received the proper unit and parts.
Controls may be shipped separately, or in same carton as unit.
6.
If you have any difficulties with installing, servicing, or operating your unit, call
your dealer or Draper, Inc., 765-987-7999.
Important Safety Information Important Safety Information
Remove
fasteners from
bracket clamps.
Run screen
DOWN to expose
dowel screws.
Loosen screws
and remove
shipping bracket.
Retighten
dowel endcap
screws.
1
2
3
4
Section 1 - Removing Shipping Brackets
(Tab-Tensioned, "V" Surfaces only)
CAUTION: DO NOT remove shipping
brackets until product has been
mounted and connected to power
(see
Section 4 in this document.)
.
Also, DO NOT OPERATE SCREEN
BEFORE REMOVING SHIPPING
BRACKETS FROM SCREEN CASE.
page 2 of 8
Access FIT E and V
CENTER of CASE
CENTER
of CASE
Engagement Bracket
With Ball Detent:
will snap into Access
Panel Support Bracket.
Access Panel
Support Bracket
1
2
Attaching Brackets:
Insert pin in top
slot and push up.
Rotate bracket
clockwise to lock
bracket in place.
Remove Screws
from both ends
of Screen Housing.
Access
Panel Door:
Pivot on Hinges.
OPEN
ACCESS
PANEL
CLOSED
ACCESS PANEL
SCREEN
HOUSING
Section 3 - Bottom Access FIT Panel Installation/Removal
Figure 3
Access case as seen from below
Bottom Access FIT panel secures to the screen housing
with two screws
(one on each end)
, and held in the closed
position by engagement brackets with ball detents that
snap into case support brackets
(Fig. 3)
.
CAUTION: For larger sizes, the following requires two people to perform safely.
Bottom flange of
Access housing
Bottom Access Panel Door
CAUTION: Beware of pinch points at ends of closure
Please Note: When locating viewing surface and checking clearance for screen operation, ensure that surface is centered in the case.
1.
Engage each case mounting bracket
(attached to case)
with top of housing
(Fig. 2)
and tighten set screws.
Section 2 - Hanging Screen
2.
Screen should be sufficiently supported to withstand
vibration.
Please Note: A hoisting bracket is included on each end of the
case to aid in overhead installation.
3.
Ensure that fasteners are of adequate strength and suitable
for the mounting surface chosen. Supporting hardware
such as chains, cables, two
3/8
"
(9.5 mm)
rods, etc., must be
precisely vertical.
4.
Entire bottom of case must be readily accessible after
installation is complete.
5.
Front, back, and top of case must be straight—not forced
to warp or bow.
CAUTION: Screen case and flange are not designed to
serve as ceiling support.
6.
Do not seal unit in ceiling until electrical connections have
been made and screen operates successfully.
Please Note: If case is painted on location, removal of roller/
fabric assembly is recommended prior to painting. If not
removed, slot on bottom of case should be shielded to
protect viewing surface from paint splatters/overspray.
HOISTING
BRACKET
CASE
MOUNTING
BRACKET
7⁄8" (22mm)
ELECTRICAL
KNOCKOUT
TYPICAL
INSTALLATION
With typical installation, brackets
may be angled to meet installation requirements.
CASE
MOUNTING
BRACKE TS
ALTERNATE
INSTALLATION
Additional set of brackets
required, but NOT included.
Figure 2
Installation of Case
Figure 4
Removing Access Panel
1.
Press up on Access FIT panel and pull toward the front of the
screen housing to disengage hinges and remove Access FIT panel.
2.
To Remove/Install Support Brackets:
page 3 of 8
Access FIT E and V
Product specificaties
| Merk: | Draper |
| Categorie: | Projectiescherm |
| Model: | Access/V |
Heb je hulp nodig?
Als je hulp nodig hebt met Draper Access/V stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Projectiescherm Draper
27 Mei 2023
28 April 2023
25 April 2023
24 April 2023
22 April 2023
19 April 2023
17 April 2023
13 April 2023
11 April 2023
11 April 2023
Handleiding Projectiescherm
- Projectiescherm Duronic
- Projectiescherm Elite
- Projectiescherm GPX
- Projectiescherm Kodak
- Projectiescherm Nec
- Projectiescherm Pyle
- Projectiescherm Vestel
- Projectiescherm Optoma
- Projectiescherm Oregon Scientific
- Projectiescherm Luxburg
- Projectiescherm Da-Lite
- Projectiescherm AV:link
- Projectiescherm Projecta
- Projectiescherm Elite Screens
- Projectiescherm EluneVision
- Projectiescherm Celexon
- Projectiescherm Lumene
- Projectiescherm Stewart
- Projectiescherm Avers
- Projectiescherm Instaal
- Projectiescherm Elite ProAV
- Projectiescherm KHOMO GEAR
- Projectiescherm EPV
Nieuwste handleidingen voor Projectiescherm
18 Augustus 2024
18 Augustus 2024
7 Augustus 2024
20 Juni 2024
20 Juni 2024
4 Mei 2024
4 Mei 2024
4 Mei 2024