Denver CAP-4320 Handleiding

Denver Receiver CAP-4320

Lees hieronder de 📖 handleiding in het Nederlandse voor Denver CAP-4320 (9 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/9

OWNER'S MANUAL

CAR AUDIO SYSTEM

PLEASE READ CAREFULLY BEFORE INSTALLING OR OPERATING THIS UNIT.

CAP-4320

WARNING

Make sure you choose a suitable place to mount the unit. The position should be completely

dry with a good circulation of air, and from a mechanical point of view very stable.

System Planning

Proper system planning is the best way to maximize your amplifier performance. By planning

your installation carefully you can avoid situations where the performance of the reliability of

your system is compromised. Your authorized dealer has been trained to maximize your

system's sonic potential. Your dealer is a valuable resource in helping you with your system

design and installation.

Speaker Requirements

Each channel of your amplifier can easily drive

4Ω speaker loads when used in the stereo

mode. When a channel-pair is bridged, the

recommended minimum load impedance is 3Ω

for subwoofer use, and 4Ω for full range

operation. Although operation with lower

impedances is not likely to cause immediate

damage to the internal circuitry, the unit will

most likely overheat, causing the thermal

protection circuitry to shut down the amplifier.

When the chassis cools down, normal operation

will resume. Continuing to operate the amplifier

under these conditions is not recommended and

will reduce its life expectancy.

Most speakers designed for car audio operation

are 4Ω impedance. Connecting two such

speakers in parallel will result in a 2Ω

impedance load as seen by the amplifier. Some

subwoofer models feature a dual 4Ω voice coil

design. Connecting these voice coils in parallel

will result in a 2Ω nominal impedance, which is

not recommended for use with bridged channels

of your amplifier.

EN EN

8Ω 8Ω

4Ω 4Ω

Series wiring Series wiring

Parallel wiring Parallel wiring

Series/parallel wiring Series/parallel wiring

• 2 •

Power Connection Leads

Notes on the power supply

Connect the + 12V power input lead only after all other leads have been connected.

Be sure to connect the ground wire of the unit securely to a metal part of the car.

A lose connection may cause a malfunction of the amplifier.

REMOTE: The unit is turned on by applying + 12Volts to this terminal. This terminal dose not

draw heavy current like the two power terminal so a thinner connecting wire is acceptable.

Standard 18 GAUGE is fine and the standard colour is yellow. If the radio is equipped with a

power antenna control wire, it can drive this terminal. If the power antenna wire is already in

use, you can still splice into it. With this method, the unit will turn on automatically with the

radio. Use the power supply lead with a fuse attached whose value is the same as original

fuse.

Place the fuse in the power supply lead as close as possible to the car battery.

During a full power operation. Maximum current will run through the system. Therefore, Make

sure the that the leads to be connected to the + 12v and GND terminals of the unit

respectively must be larger than 10-Gauge (AWG. 10).

• 3 •

Product specificaties

Merk:	Denver
Categorie:	Receiver
Model:	CAP-4320
Kleur van het product:	Zwart
Breedte:	280 mm
Diepte:	50 mm
Hoogte:	170 mm
Breedte verpakking:	370 mm
Diepte verpakking:	760 mm
Hoogte verpakking:	189 mm
Materiaal behuizing:	Aluminium
Frequentiebereik:	20 - 20000 Hz
Signaal/ruis-verhouding:	90 dB
Hoeveelheid per (buitenste) hoofdverpakking:	4 stuk(s)
Maximaal uitgangsvermogen (RMS):	1000 W
Producten per intermodale container (40 ft - High Cube):	8400 stuk(s)
Producten per intermodale container (20 ft):	3460 stuk(s)
Audio RCA-ingangen:	2
Aantal versterker kanalen:	4 kanalen
RMS vermogen uitvoer per kanaal (4 Ohm):	240 W
RMS vermogen uitvoer per kanaal (2 Ohm):	360 W
Overbrugd uitgangsvermogen (max):	360 W