Denver CAP-4300 Handleiding

Denver Receiver CAP-4300

Lees hieronder de 📖 handleiding in het Nederlandse voor Denver CAP-4300 (10 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/10

HIGH EFFICIENCY POWER AMPLIFIER

OWNER'S MANUAL

CAR AUDIO SYSTEM

PLEASE READ CAREFULLY BEFORE INSTALLING OR OPERATING THIS UNIT

CAP-4300

WARNING

Make sure you choose a suitable place to mount the unit. The position should be completely dry

with a good circulation of air, and from a mechanical point of view very stable.

ENG-1

System planning

Proper system planning is the best way to

maximize your ampliﬁer performance. By

planning your installation carefully you can

avoid situations where the performance of the

reliability of your system is compromised. Your

authorized dealer has been trained to

maximize your system's sonic potential. Your

dealer is a valuable resource in helping you

with your system design and installation.

Speaker requirements

Each channel of your ampliﬁer can easily drive

4 speaker loads when used in the stereo Ω

mode. When a channel-pair is bridged, the

recommended minimum load impedance is 3 Ω

for subwoofer use, and 4 for full range Ω

operation. Although operation with lower

impedances is not likely to cause immediate

damage to the internal circuitry, the unit will

most likely overheat, causing the thermal

protection circuitry to shut down the ampliﬁer.

When the chassis cools down, normal

operation will resume. Continuing to operate

the ampliﬁer under these conditions is not

recommended and will reduce its life

expectancy.

Most speakers designed for car audio

operation are 4 impedance. Connecting two Ω

such speakers in parallel will result in a 2 Ω

impedance load as seen by the ampliﬁer.

Some subwoofer models feature a dual 4 Ω

voice coil design. Connecting these voice coils

in parallel will result in a 2 nominal Ω

impedance, which is not recommended for use

with bridged channels of your ampliﬁer.

Series wiring

Parallel wiring

Series/parallel wiring

ENG-2

Power Connection Leads

Notes on the power supply

Connect the + 12V power input lead only after all other leads have been connected.

Be sure to connect the ground wire of the unit securely to a metal part of the car.

A lose connection may cause a malfunction of the ampliﬁer.

REMOTE: The unit is turned on by applying + 12Volts to this terminal This terminal dose

not draw heavy current like the two power terminal so a thinner connecting wire is

acceptable. Standard 18 GAUGE is ﬁne and the standard colour is yellow. If the radio is

equipped with a power antenna control wire, it can drive this terminal. If the power

antenna wire is already in use, you can still splice into it. With this method, the unit will

turn on automatically with the radio. Use the power supply lead with a fuse attached

whose value is the same as original fuse.

Place the fuse in the power supply lead as close as possible to the car battery.

During a full power operation, Maximum current will run through the system. Therefore,

Make sure that the leads to be connected to the + 12v and GND terminals of the unit

respectively must be larger than 10-Gauge (AWG. 10).

Product specificaties

Merk:	Denver
Categorie:	Receiver
Model:	CAP-4300
Kleur van het product:	Aluminium, Black
Gewicht:	2600 g
Breedte:	220 mm
Diepte:	358 mm
Hoogte:	50 mm
Breedte verpakking:	246 mm
Diepte verpakking:	435 mm
Hoogte verpakking:	65 mm
Materiaal behuizing:	Aluminium
Connectiviteitstechnologie:	Bedraad
Afmetingen verpakking (BxDxH):	246 x 435 x 65 mm
DC voltage input:	12 V
Bedoeld voor:	Auto
Audio-uitgangskanalen:	4.0 kanalen
Frequentiebereik:	20 - 20000 Hz
Signaal/ruis-verhouding:	88 dB
Totale harmonische vervorming (THD):	- procent
Maximaal uitgangsvermogen (RMS):	1000 W
Producten per intermodale container (40 ft - High Cube):	8400 stuk(s)
Producten per intermodale container (20 ft):	3460 stuk(s)
Piekvermogen per kanaal:	- W
Aantal versterker kanalen:	4 kanalen
RMS vermogen uitvoer per kanaal (4 Ohm):	360 W
Bridge-mode vermogen uitvoer per kanaal (4 Ohm):	360 W