Delta Dore Minor 1000 Handleiding

Delta Dore Thermostaat Minor 1000

Lees hieronder de 📖 handleiding in het Nederlandse voor Delta Dore Minor 1000 (1 pagina's) in de categorie Thermostaat. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

1. Technical characteristics

• Powered by 2 1.5 V lithium batteries,

LR03/AAA type (supplied),10-year life

(if menu CF05=0)

• Blue backlit display

• Class III insulation

•

X3D wireless remote control device:

868.7 MHz to 869.2 MHz

• Maximum wireless power < 10mW

• Category 2 receiver

•

Wireless range from 100 to 300 metres outside, varies

depending on the associated equipment (the range can

vary depending on the installation conditions and the

electromagnetic environment).

• Dimensions: 81 x 88 x 21 mm

• Degree of protection: IP 30

• Wall mounting or base unit

• Storage temperature: -10°C to +70°C

• Operating temperature: 0°C to +40°C

2. Location - Mounting

Since the temperature measurement sensor is inside

the box, you must install the thermostat ush-mount-

ing box:

- on an accessible wall at a height of 1.50 m

- away from heat sources (replaces, sunlight) and

draughts (windows, doors)

IMPORTANT:

Do not install the thermostat on a wall in contact with

the outdoors or with an unheated room

(e.g. garage, etc.)

The sleeve output in the ush-mounting box must be

blanked off (with mastic) in order to avoid unwanted

air movements that could bias the sensor reading.

❶ Separate the box from its base unit by pushing the

pin using a screwdriver.

❷ Insert the batteries, with the right polarity

❸ Wall mount: attach the mount with suitable fasten-

ings and remount the unit onto its mount.

Placed on furniture: ret the base on the unit, then

assemble these to the mount.

1,50 m

> 20 cm

A B

3. Association

With the receiver(s):

❶ Press and hold the receiver button for 3 seconds

until the LED ashes.

Release.

1- No receiver has been associated with the thermostat:

❷ Press any button to display rF01.

❸ Press on OK, the screen displays “00”

❹ Press the OK button for 3 seconds.

The screen ashes, and the thermostat searches for

receivers to associate with. The number of receivers

found and associated with is displayed on the screen.

1 2 3 4

❺ When the screen stops ashing, press on the OK

button

❻ The screen displays “Loc”, the rst receiver is

identied by its relay ashing. Note the power of

the radiator in question.

Press OK.

❼

Report the value of the radiator

using the + and - buttons and

then press on OK.

❽ If required, repeat stages

❻ ❼ and for the other registered receivers.

2- Receivers are already associated with the thermostat.

The thermostat must be in shutdown mode.

❶ Press and hold the receiver button for 3 seconds

until the LED ashes. Release.

❷ Press the 1 and 2 buttons at the same time and

hold for 5 seconds. The screen will display rF01.

❸ ❸ Continue the association procedure from stage

of the previous paragraph.

4. Conguration

The thermostat must be in shutdown mode.

❶ Press and hold the 1 button for 5 seconds.

The screen displays the CF01 menu.

❷ Make a selection or adjust using + and -.

Press OK to validate and go to the next setting.

To exit the mode, press the button

Comment: the greyed-out sections of the tables

correspond to default values.

CF01 -

Correcting the temperature measured

Adjustable by -5°C to +5°C (default value: 0.0°C).

Example: if the temperature displayed by the unit is

19°C and the actual temperature (thermometer) is

20°C, set +1°C.

CF02 - Temperature displayed in AUTO mode

CF04 - Control type

PWM control,

1All or Nothing control

CF05 - Energy saving mode

CF07 - Backlighting

... ... ...

> 3s

1 2 3 41 2 3 4

5 6

1 2 3 4

1 2 3 4 1 2 3 4

0 Temperature setting

1Measured temperature

0 Display turns off after a 10-seconds without

press

2 Display always illuminated

0 Deactivated

1Enabled (off after timeout)

CF08 - Door/window magnetic contact function

When a magnetic contact is installed on a window and

associated with a receiver, activate function CF08: the

opening of the window will switch the heating to frost

protection mode, and the symbol ashes.

CF09 - Presence detection function

When a motion detector is associated with a receiver,

activate function CF09, resulting in an automatic re-

duction in the temperature in the case of a prolonged

absence:

• 1h30min -> current setting -1.5°C

• 3h -> current setting -3°C

• 48h -> Frost protection setting

The symbol ashes.

CF10 - Maximum setting value

Setting from 16°C to 40°C in increments of 0.5°C.

Default value: 30°C

CF16 - Display of symbol

(heating request)

CF19 - Consumption display

CF22 - Display of relative humidity %

CF26 -

Adjustment of frost protection setting

Adjustment possible from 5°C to 10°C in increments

of 0.5°C.

Default value: 8°C

CF27 -

Display of external temperature

Requires an outdoor X3D sensor associated with the

receiver.

5. Use

Information button

The information button ( ) shows the following i

information:

- Measured temperature or current

temperature setting (as per conguration),

- Outdoor temperature, if the receiver is associated

with an outdoor sensor (menu CF27 activated).

- Display of total consumption of associated heating

devices. (menu CF19 activated).

Counter reset to zero: Press and hold the C button

for 3 seconds.

- Display the relative humidity (menu CF22 activated)

Successively press the i button to display this infor-

mation.

Locking down settings

Press and hold the i button for 5 seconds.

The symbol appears. In locked mode, only the Start

/ Stop ( ) and information ( i ) buttons are accessible.

To unlock, press and hold the i button for 5 seconds.

The symbol disappears.

Off mode

Press . In The thermostat emits a series of 3 beeps.

this mode, heating is shut down.

To exit from shutdown mode, press the button

again. The thermostat beeps.

6. Troubleshooting

Automatic reset of initial settings

From the Shutdown mode ( ) .

❶ Press and hold the 1 and 3 buttons simultaneously

for 10 seconds until "Init" is displayed

(slow ashing).

❷ Press and hold OK for 3 seconds.

1 2 3 4 1 2 3 4

The following parameters are initiated:

- Door/window magnetic contact function (CF08=0),

- Presence detection function (CF09=0),

- Setting value: 19°C.

0 Deactivated

1Activated

0 Deactivated

1Activated

0 Symbol not displayed

1Symbol displayed

0 Deactivated

1Activated

0 Deactivated

1Activated

0 Deactivated

1Activated

6 7 8 9

1210

❶ On/Off button

❷ Information button

❸ Measured temperature

or temperature setting

❹ Measured temperature

❺ Heating request

❻ Presence detection

active

❼ Window/door magnetic contact active

❽ Locking of access to settings

❾ Batteries old

❿Settings buttons

All settings initialised

From the Shutdown mode ( ) .

❶ Simultaneously press buttons 1 and 3 until "Init"

is displayed (slow ash). release the buttons and then

press on buttons 1 and 3 again for a further 10

seconds until "init" is displayed

(fast ash).

❷ Press and hold OK for 3 seconds.

All parameters of the conguration menu are reset

to default value.

Setting value: 19°C.

Removing all associations

To remove all the associated receivers.

The thermostat must be in shutdown mode.

❶ Press the 1 and 2 buttons at the same time and

hold for 5 seconds. The screen will display rF01.

❷ Press button 2 twice. The screen will display rF03.

❸ Press the OK button, and the thermostat will

display the associated number of receivers.

❹

Keep the OK button pressed for 3 seconds.

All the associated receivers are removed.

The "i" symbol is ashing.

The thermostat is indicating an error in wireless communication.

- Press the ( i ) button.

Check:

1- The power supply to the system.

2- If one or more receivers are off.

3- That the thermostat is within wireless range of all

the associated receivers.

4- If one or more receivers does not work.

In the case that a receiver is out of order, you can

remove the association with this faulty receiver.

❶ Press the Stop button ( )

❷ Press the 1 and 2 buttons at the same time and hold

for 5 seconds. The screen will display rF01.

❸ Press 3 times on button 2. The screen will display

rF04.

❹ Press the OK button, and the thermostat will dis-

play the associated number of receivers.

❺ Then press OK for 3 seconds.

The association with the faulty receiver(s) is deleted,

and the "i" symbol will stop ashing.

Activating association wait mode for receivers

already associated with MINOR 1000.

From the Off mode ( ).

❶ Press the 1 and 2 buttons at the same time and hold

for 5 seconds. The screen will display rF01.

❷ Press button 4 twice. The screen will display rF05.

❸ Press OK. The screen will display ALL:

Activating association wait mode for

all associated receivers. Press OK for 3

seconds.

If you want to select one receiver from all the receivers

already associated, press +. The screen will display Loc:

Individual association wait mode.

Repeatedly press the + or -- button to

select the required receiver, its LED

ashes and its relay operates.

Press OK for 3 seconds.

Proceed in the same manner for each receiver to

associate.

Next, associate the product (door/window magnetic

contact for example) with the receiver or receivers,

refer to its user guide.

Press ( ) to exit the mode if necessary.

Changing batteries

Form the moment when the symbol is displayed on

the screen, you have around 3 months to change the

batteries (see technical characteristics).

Display the software version

From shutdown mode ( ).

- Press button 2 for 5 seconds to display the software version.

1 2 3 4

- Press button C to leave the mode.

1 2 3 4 1 2 3 4 1 2 3 4

Remote control and programming option

Add the TYDOM 1.0 home automation gateway

to your system and benet from

remote control and programming

features using the TYDOM smartphone

and tablet application.

Wireless room thermostat

www.deltadore.com

MINOR 1000

Standby mode:

When left idle for a given period of time, the thermo-

stat switches to standby. To wake the thermostat up,

press any button.

Product specificaties

Merk:	Delta Dore
Categorie:	Thermostaat
Model:	Minor 1000

Heb je hulp nodig?

Als je hulp nodig hebt met Delta Dore Minor 1000 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Thermostaat Delta Dore

Delta Dore TYDOM 1.0 Handleiding

16 November 2024

Delta Dore Tybox 5701 FP Handleiding

16 November 2024

Delta Dore Tybox 33 Handleiding

16 November 2024

Delta Dore Tybox 5702 FP Handleiding

16 November 2024

Delta Dore Tybox 31 Handleiding

16 November 2024

Delta Dore TYBOX 827 W RF Handleiding

16 November 2024

Delta Dore Delta 8000 TAP BUS Handleiding

16 November 2024

Delta Dore Delta 8000 TAP RF Handleiding

16 November 2024

Delta Dore Tybox 34 Handleiding

16 November 2024

Delta Dore Delta 8000 TA BUS Handleiding

16 November 2024

Handleiding Thermostaat

Nieuwste handleidingen voor Thermostaat

Tru Components TCN4S-24R Handleiding

18 December 2024

Tru Components TK4S-14RC Handleiding

18 December 2024

Tru Components TX4S-14R Handleiding

17 December 2024

Warmup 5iE Handleiding

16 December 2024

Warmup +Kit Handleiding

16 December 2024

Nobo Connect SWT-IZW Handleiding

15 December 2024

Nobo Connect SWT-IZB Handleiding

11 December 2024

Hive Thermostat Handleiding

10 December 2024

GENERAL Life HT15S Handleiding

9 December 2024

GENERAL Life HT15 Handleiding

9 December 2024