CRUX VIMHK-97 Handleiding


Lees hieronder de šŸ“– handleiding in het Nederlandse voor CRUX VIMHK-97 (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
2016 Kia Sorrento
- with 8ā€ Navigaon screen.
Cable colour
Pin-No.
Assignment
ā— Yellow
Pin 4
CAN-HIGH connecon to the head-unit–
ā— Blue
Pin 3
CAN-LOW connecon to the head-unit –
ā—ā— Yellow/Black
Pin 8
CAN-HIGH connecon to the vehicle –
ā—ā— Blue/Black
Pin 7
CAN-LOW connecon to the vehicle –
ā— Red
Pin 1
+12V Constant
ā— Black
Pin 5
Ground
ā— Green
Pin 6
Acvaon of the Video- -Moon funcon in
(+12V = VIM Enabled )
ā— White
Pin 2
Trigger output (+12V DC 500mA)
VIMHK- Interface Module 97
HK- Harness 97
rev.0612 16
1 /2
Connector A Connector B
Please note that the given informaon must be veriī… ed by the installer. Crux Interfacing assumes
no liability for changes in wire color or pin assignments made by the vehicle manufacturer.
For video in moon, cut and insulate the analog speed signal wire (pin 17, connector B)
(navigaon will sll work over GPS recepon An oponal toggle switch can be installed in ).
between the cut speed signal wire in case the GPS recepon is bad or not available.
Connector
Assignment
Connector B, Pin 11/12
+12V Constant (Red)
Connector B, Pin 23/24
Ground (Black)
Connector B, Pin 1
CAN-HIGH (Yellow)
Connector B, Pin 13
CAN-LOW (Blue)
Connector B, Pin 16
Speedsignal (Gray)
rev.0 61216
2 3 /
DIP Switch Seī‡ng
Vehicle/ Navigaī‡ƒon
Dip 1
Dip 2
Dip 3
Dip 4
Dip 5
Dip 6
All vehicles
ON
OFF
OFF
OFF
OFF
OFF
DIP Switch Funcī‡ƒons:
Dip 1 ON = Video In Moon enabled –
Dip 2 ON = If factory rear-view camera is present –
Dip 3 no funcon (set to OFF) –
Dip 4 no funcon (set to OFF) –
Dip 5 CAN-bus terminaon resistor on the vehicle side –
Dip 6 CAN-bus terminaon resistor on the head-unit side –
Acī‡ƒvaī‡ƒon of the Video-In-Moī‡ƒon funcī‡ƒon
The Video- -Moon can be acvated and deacvated by DIP 1 or by the loose green wire on the In
harness when connected to a +12V ACC source.
Video- -Moon permanent In
With DIP1 set to ON, the video- -moon funcon is acvated permanently without disturbing the in
navigaon performance.
Video- -moon selecve in
With DIP1 set to OFF, the green wire is used to acvate and deacvate the video- -moon funcon. in
Connect a toggle switch between the green wire and +12V ACC.
ā— +12V = Video- -moon is acvated in
ā— 0V = Video- -moon is not acvatedin
rev.0 61216
3 3 /


Product specificaties

Merk: CRUX
Categorie: Niet gecategoriseerd
Model: VIMHK-97

Heb je hulp nodig?

Als je hulp nodig hebt met CRUX VIMHK-97 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd CRUX

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd