CRUX VIMFD-95 Handleiding

CRUX Niet gecategoriseerd VIMFD-95

Lees hieronder de 📖 handleiding in het Nederlandse voor CRUX VIMFD-95 (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 6 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/3
TO FACTORY
DISPLAY HARNESS
8-PIN
(male plug)
WHITE/ OPTIONAL
12V OUTPUT
54-PIN
(female plug)
54-PIN
(male plug)
8-PIN
(male plug)
TO FACTORY
DISPLAY
4 5 6
ON
1 2 3
4 5 6
ON
1 2 3
------------------
------------------
------------------
BOTH GREEN/ 12V POWER SWITCH
(SAME FUNCTION AS DIP 1)
NON-PERMANENT
12V
MUST USE
TOGGLE SWITCH
(INCLUDED)
WHITE/ OPTIONAL
12V OUTPUT
C-500
INTERFACE
C-125
INTERFACE
WHITE/ OPTIONAL
12V OUTPUT
RED
12V CONSTANT
SEE PAGE 2
FOR TOGGLE SWITCH
USE (INCLUDED)
TAP RED WIRE FOR 12V CONSTANT
(TO BE USED FOR TOGGLE SWITCH)
SAFETY WARNING:
THIS INTERFACE IS DESIGNED TO ACTIVATE VIDEO IN-
MOTION TO ALLOW THE PASSENGER ACCESS TO THE
ADDRESS INPUT WHILE THE VEHICLE IS IN-MOTION. THIS
INTERFACE MAY CAUSE AN ERROR WHEN SERVICED AT
THE OEM DEALER. BE AWARE THAT MOST DEALERS
WILL ATTEMPT TO VOID THE MANUFACTURERS
WARRANTY WHEN INSTALLING ANY AFTERMARKET
EQUIPMENT. IMPROPER USE OF THIS INTERFACE BY THE
DRIVER MAY RESULT IN CITATION. DRIVER MUST KEEP
FULL ATTENTION ON THE ROAD AND RESPONSIBILITY
ON THE SAFETY OF THEIR PASSENGERS.
INTERFACING SO LUTIONS
VIDEO IN-MOTION ACTIVATION FOR SELECT FORD MyFord Touch RADIOS 2013-UP
FORD
2013 - 2015 F150
2013 - 2015 F150 Raptor
2013 - 2015 F250
2013 - 2015 F350
2013 - 2015 F450
2013 - 2015 F550
Installer must use Toggle Switch for
VIM Control. (See diagram on page 2)
WORKS FOR ALL:
MyFord Touch Radios
SONY AND NON-SONY SYSTEMS
Activating the VIM will aect the GPS
System.
(May cause delay in location updates)
C-125 & C-500 MODULE:
SW: 2.0.3
WORKS FOR ALL:
MyFord Touch Radios
SONY AND NON-SONY SYSTEMS
VIMFD-95F We recommend reading this installation guide rst before starting any
work. Following these instructions from “Start” to” Finish” will ensure
a smooth and hassle free installation. We oer telephone support M-F
9:00 AM – 5:00 PM PDT at 1 (855) 822-1348. We are here to help.
PARTS INCLUDED:
(1) FD-95 C-500 Interface
(1) FD-95 C-125 Interfaces
(1) FD-95 T-Harness
(1) Toggle Switch
(1) Instruction
PRECAUTIONS:
- Remove the negative side of the battery to avoid any short circuits
during the installation.
- Do not install the interface near any major components or near the
HVAC system. This may cause damage or overheating to the vehicle.
- Do not disconnect the airbag connection behind the radio panel.
PRELIMINARY:
Please read the entire manual before installing this interface.
This interface does not activate DVD reader.
INSTALLING THE INTERFACE:
1. Remove the factory display to gain access to the factory connectors.
2. Remove the 54-Pin connector from behind the display.
3. Make the T-Harness connections behind the factory display.
(if the connectors do not match please contact tech support)
4. Connect both Interfaces to an 8-Pin connector. No orientation.
4. Set the dip switches as needed on both interfaces. (See below)
5. Test the Navigation address input while the car is in-motion to verify
the VIM is active.
As an option we have provided a 12v output wire from our
interface, as the vehicle does not provide a 12v source.
Not all vehicles support this feature.
INSTALLATION OVERVIEW
Rev. 012115
TROUBLE SHOOTING
1. No video display while in-motion.
- Make sure the dip switches are in the correct position.
- Start the vehicle and drive more than 10 feet.
CONNECT BEHIND
THE DISPLAY
(Not The Radio)
SETTING THE DIP SWITCHES
Dip 1: Set to OFF.
Dip 2,3,4: Not Used
Dip 5: Place to the OFF position on both interfaces.
Dip 6: Place to the ON position on both interfaces.
Activating the VIM will effect the GPS System.
(May cause delay in location updates)
FOR DIP SWITCH SETTINGS
SEE ATTACHED
SLIP SHEET
(Page 2)
BACK OF FACTORY
DISPLAY
(Not The Radio)
MUST USE TOGGLE SWITCH TO
ACTIVATE VIM
INTERFACING SOLUTIONS
VIDEO IN-MOTION ACTIVATION FOR SELECT FORD MyFord Touch RADIOS 2013-UP
FORD
2013 - 2015 F150
2013 - 2015 F150 Raptor
2013 - 2015 F250
2013 - 2015 F350
2013 - 2015 F450
2013 - 2015 F550
Installer must use Toggle Switch for
VIM Control. (See diagram on page 2)
WORKS FOR ALL:
MyFord Touch Radios
SONY AND NON-SONY SYSTEMS
Activating the VIM will aect the GPS
System.
(May cause delay in location updates)
C-125 & C-500 MODULE:
SW: 2.0.3
WORKS FOR ALL:
MyFord Touch Radios
SONY AND NON-SONY SYSTEMS
VIMFD-95F
Rev. 012115
PIN 1/ VIM CONTROL CONFIGURATION
DIP# C-125 C-500 RESULT
Dip 1 OFF OFF
Dip 1 ON ON
User control of the VIM feature will be
turned ON and OFF from
Toggle Switch
VIM Permanently on. No control Toggle
Switch. Recommended
for vehicles w/o factory GPS.
DIP SWITCHES SLIP SHEET
Dip 2 OFF OFF Note Used
Dip 3 OFF OFF Not Used.
Dip 4 OFF OFF Not Used.
Dip 5 OFF OFF CAN Termination.
Dip 6 ON ON CAN Termination.
INSTALLING THE TOGGLE SWITCH
8-PIN
(male plug)
12V
CONSTANT
INCLUDED
TOGGLE SWITCH
WHITE/ OPTIONAL
12V OUTPUT
(MAY )VARY
GREEN/ 12V SWITCH
(SAME FUNCTION AS DIP 1)
NON-PERMANENT
RED/ 12V CONSTANT
DEACTIVE/
CURRENT
POSITION
=
C-500
(Wire View)
TAP HERE
C-500
8-PIN
(male plug)
WHITE/
OPTIONAL
12V OUTPUT
(MAY )VARY
C-125
C-125
GREEN/ 12V SWITCH
To activate the Video In-Motion you will need to add a toggle switch to turn on and
o. Use both GREEN wires from both modules to power the switch.
You will be able to use the 8-Pin connector from the C-500 interface module to
power the switch. Use the RED wire as your constant source for the toggle switch
and both of the GREEN wires from the T-Harness.
MUST USE TOGGLE SWITCH TO
ACTIVATE VIM
INTERFACING SOLUTIONS
VIDEO IN-MOTION ACTIVATION FOR SELECT FORD MyFord Touch RADIOS 2013-UP
FORD
2013 - 2015 F150
2013 - 2015 F150 Raptor
2013 - 2015 F250
2013 - 2015 F350
2013 - 2015 F450
2013 - 2015 F550
Installer must use Toggle Switch for
VIM Control. (See diagram on page 2)
WORKS FOR ALL:
MyFord Touch Radios
SONY AND NON-SONY SYSTEMS
Activating the VIM will aect the GPS
System.
(May cause delay in location updates)
C-125 & C-500 MODULE:
SW: 2.0.3
WORKS FOR ALL:
MyFord Touch Radios
SONY AND NON-SONY SYSTEMS
VIMFD-95F
Rev. 012115
COMPATIBLE RADIO: SONY AND NON-SONY 8” RADIOS
MUST USE TOGGLE SWITCH
MUST USE TOGGLE SWITCH TO
ACTIVATE VIM

Product specificaties

Merk: CRUX
Categorie: Niet gecategoriseerd
Model: VIMFD-95

Heb je hulp nodig?

Als je hulp nodig hebt met CRUX VIMFD-95 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd CRUX

CRUX

CRUX VIMCF-93E Handleiding

10 Maart 2025
CRUX

CRUX VIMBM-86 Handleiding

10 Maart 2025
CRUX

CRUX VIMBM-87 Handleiding

10 Maart 2025
CRUX

CRUX VIMFD-95 Handleiding

10 Maart 2025
CRUX

CRUX VIMTY-05 Handleiding

9 Maart 2025
CRUX

CRUX VIMVL-98B Handleiding

9 Maart 2025
CRUX

CRUX VIMHN-96 Handleiding

9 Maart 2025
CRUX

CRUX VIMLR-89B Handleiding

9 Maart 2025
CRUX

CRUX VIMGM-94 Handleiding

9 Maart 2025
CRUX

CRUX VIMVL-98A Handleiding

9 Maart 2025

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Parkside

Parkside PEX 270 C3 Handleiding

10 Maart 2025
Smart-AVI

Smart-AVI EZWALL-Pro 3×3 V3 Handleiding

10 Maart 2025
Smart-AVI

Smart-AVI EZWall-Pro 4x4 Handleiding

10 Maart 2025
Parkside

Parkside PUV 2000 A1 Handleiding

10 Maart 2025
Smart-AVI

Smart-AVI MXWall-UHD 8×8 Handleiding

10 Maart 2025
Smart-AVI

Smart-AVI MXwall Pro V2 Handleiding

10 Maart 2025
Parkside

Parkside PPM 800 A1 Handleiding

10 Maart 2025
Parkside

Parkside PPFSA 40-Li C2 Handleiding

10 Maart 2025
Alpine

Alpine PSS-TSLA-213P Handleiding

10 Maart 2025
Parkside

Parkside PFDF 900 C3 Handleiding

10 Maart 2025