CRUX VIMCF-93E Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor CRUX VIMCF-93E (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 5 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
8-PIN
(male plug)
4 5 6
TO ENABLE VIDEO
IN-MOTION 1. On = Enable VIM
2. On = If Factory Back-Up Present
3. Not Used
4. Not Used
5. May Vary
6. May Vary
ON
1 2 3
WHITE/ OPTIONAL
12V OUTPUT
GREEN/ 12V POWER SWITCH
(SAME FUNCTION AS DIP 1)
NON-PERMANENT
FUSE
(NOT INCLUDED)
12V OPTIONAL/
TOGGLE SWITCH
NOT INCLUDED
4 5 6
ON
1 2 3
TO FACTORY
HARNESS
TO FACTORY
RADIO
22-PIN
(male plug)
22-PIN
(female plug)
VOLUME T UNE
8.4” RADIO
DISPLAY
WHITE
WHITE
SAFETY WARNING:
THIS INTERFACE IS DESIGNED TO ACTIVATE
VIDEO IN-MOTION TO ALLOW THE PASSENER
ACCESS TO THE ADDRESS INPUT WHILE THE
VEHICLE IS IN-MOTION. THIS INTERFACE MAY
CAUSE AN ERROR WHEN SERVICED AT THE OEM
DEALER. BE AWARE THAT MOST DEALERS
WILL ATTEMPT TO VOID THE MANUFACTURERS
WARANTY WHEN INSTALLING ANY AFTERMARKET
EQUIPMENT. IMPROPER USE OF THIS INTERFACE
BY THE DRIVER MAY RESULT IN CITATION. DRIVER
MUST KEEP FULL ATTENTION ON THE ROAD AND
RESPOSIBILITY ON THE SAFETY OF HIS
PASSENGERS.
INTERFACI N G SOLUTION S
VIDEO IN-MOTION ACTIVATION FOR CHRYSLER 300 2011-2014
CHRYSLER:
2011 - 2014 300
2011 - 2013 Charger
VIMCF-93E We recommend reading this installation guide rst before starting any
work. Following these instructions from “Start” to” Finish” will ensure
a smooth and hassle free installation. We oer telephone support M-F
9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help.
PARTS INCLUDED:
(1) CF-93E Interface
(1) CR-93E T-Harness (2598)
(1) Instruction
PRECAUTIONS:
- Remove the negative side of the battery to avoid any short circuits
durring the installation.
- Do not install the interface near any major components or near the
HVAC system. This may cause damage or overheating to the vehicle.
- Do not disconnect the airbag connection behind the radio panel.
PRELIMINARY:
Please read the entire mannual before installing this interface.
Vehicle must be equipped with factory DVD changer.
This interface does not activate DVD reader.
INSTALLATION OVERVIEW
TROUBLE SHOOTING
1. No video display while driving.
- Make sure the dip swithces are in the proper location.
Rev. 111413
INSTALLING THE INTERFACE:
1. Remove the factory radio to gain access to the factory connectors.
2. Remove the 22-Pin connector from behind the radio.
2. Make the T-Harness connections behind the factory radio.
(if the connectors do not match please contact tech support)
4. Set the sip switches to permanently activate the VIM feature.
5. Test the Navigation address input while the car is in-motion to verify
the VIM is active.
As an option we have provided a 12v output wire from our inter-
face, as the vehicle does not provide 12v Acc. Do not use if not
needed.
Dip 1: Activates the Video In-Motion feature. The dip switch
is the permanent solution for keeping the VIM unlocked.
Use the Green wire with a toggle switch for a non-permanent
solution. (Switch not included)
Dip 2: If factory back-up camera is present turn to ON, otherwise OFF.
Dip 5 & 6: Varies, these switches are defaulted both to OFF.
If the radio is having turn-on issues please try the following:
Attempt One: Set both 5 & 6 to the ON position.
Attempt Two: Set 5 to On and 6 to OFF.
Attempt Three: Set 5 to OFF and 6 to ON.
If none of the above solutions work out for your vehicle please
contact tech support.
SETTING THE DIP SWITCHES
CONNECTIONS ARE DONE
BEHIND THE RADIO.
NOT THE DISPLAY
COMPATIBLE RADIO:
8.4” U-CONNECT RADIO/ 2-PIECE RADIO


Product specificaties

Merk: CRUX
Categorie: Niet gecategoriseerd
Model: VIMCF-93E

Heb je hulp nodig?

Als je hulp nodig hebt met CRUX VIMCF-93E stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd CRUX

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd