CRUX PCM-3F Handleiding

CRUX Niet gecategoriseerd PCM-3F

Lees hieronder de 📖 handleiding in het Nederlandse voor CRUX PCM-3F (6 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 12 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/6
PCM-3F
Rear & Front View Integration Interface
for Porsche Vehicles with PCM 3 & 3.1 Navigation Systems
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.021122
1 of 6
• Rear & Front View Camera Inputs
• Oponal coding of ParkAssist to retrot factory PDC
• Automacally switches screen to Rear-view when Reverse gear is engaged and to Front camera view when gear is
engaged to drive. (compable in vehicle with automac transmission only)
• Manual acvaon of the front camera using the steering wheel control buon
• Plug & Play Installaon
• Video in Moon funcon
PRODUCT FEATURES:
PARTS INCLUDED:
PCM-3F Module PCM-3F Harness
INSTALLATION DIAGRAM:
Female Quadlock
Vehicle Harness
Rear-View
Camera Input
OEM Rear-View Camera
Front-View
Camera Input
Aftermarket
Rear-Vew Camera
(not Included)
Aftermarket
Front-View Camera
(not Included)
Rear Camera Output 12V (GREEN)
Front Camera Output 12V (WHITE)
Male Quadlock
Connector behind the
headunit
OR
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.021122
2 of 6
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
DIP SWITCH SETTINGS:
INSTALLATION INSTRUCTIONS:
CONNECTING THE INTEFACE MODULE
1. Remove the headunit.
2. Connect the female 12-Pin Molex connector of the PCM-3F T-harness to the interface module.
3. Unplug the female Quadlock connector from behind the headunit and plug it into the PCM-3F T-harness.
4. Plug the male Quadlock of the PCM-3F T-harness to the headunit.
CONNECTING THE FACTORY REAR-VIEW CAMERA (Compable with NTSC cameras only)
5. If the OEM rear-view camera will be used, plug in the male RCA labeled “OEM Rear-View Camera” to the female RCA
labeled “Rear-View Camera”.
CONNECTING THE AFTERMARKET CAMERAS (Compable with NTSC cameras only)
6. If using an aermarket rear-view camera, install the aermarket camera behind the vehicle and run the cable towards the
radio. Plug in the male RCA of the aermarket rear-view camer to the female RCA labeled “Rear-View Camera”.
7. Connect the GREEN wire on the T-harness to the 12V power wire of the aermarket camera. The GREEN wire will provide
12 volts power to the camera when the reverse gear is engaged. Power will deacvate automacally when the gear is set
to drive and speed reaches to 12 MPH.
8. If an aermarket front-view camera will be used, install the camera per manufacturer’s installaon instrucons and run
the extension cable towards the radio. Plug in the male RCA of the aermarket rear-view camer to the female RCA labeled
“Front-View Camera”.
9. Connect the WHITE wire on the T-harness to the 12V power wire of the aermarket camera. The WHITE wire will provide
12 volts power to the camera when the gear is set to drive. Power will deacvate automacally when the speed reaches
12 MPH.
Navigaon System DIP 1 DIP2 DIP3 DIP4 DIP5 DIP6
PCM3 with VIM Acvated OFF OFF OFF OFFON ON
PCM3 with VIM Deacvated OFF OFF OFF OFF OFFON
PCM3.1 with VIM Acvated OFF OFF OFFON ON ON
PCM3.1 with VIM Deacvated OFF OFF OFF OFFON ON
DIP SWITCH FUNCTIONS:
DIP 1 = Video in Moon Acvaon
DIP 2 = ON for Aermarket Rear View Camera / OFF for OEM Rear View Camera
DIP 3 = Rear View Camera Coding (see page 3)
DIP 4 = ParkAssist Coding for PCM3.1 systems only (see page 4)
DIP 5 = Camera/ParkAssist Coding (see page 5)
DIP 6 = CAN Bus Terminaon
The interface module is installed behind the headunit.
PCM-3F
Rear & Front View Integration Interface
for Porsche Vehicles with PCM 3 & 3.1 Navigation Systems
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.021122
3 of 6
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
CODING THE RADIO FOR CAMERA FUNCTION:
PCM3.1 Systems
It is necessary to code the rear-view camera input of the PCM3.1 system for use with an aermarket rear-view camera.
Le side Steering Wheel Buons Right side Steering Wheel Buons
HASH KEY/MODE
PICK UP
HANG UP
BACK
1. Turn ignion to ON.
2. Wait unl the headunit has completely booted and is in the home screen.
3. Make sure that the LEDs on the interface module is visible during this process. The LEDs are inside the module and are
visible through the side of the male 8-pin Molex connector.
4. Please observe the proper coding sequence: First press and hold the HASH KEY/MODE then press and hold the PICK UP
buon. Connue to hold both buons and check if the RED and BLUE LEDs are blinking. The PCM system will reset aer
5-10 seconds.
5. Release both buons.
6. The RED and BLUE LEDs will light up solid.
7. “Rear-View Camera” will show on the radio menu opon aer a successful coding.
To decode the aermarket rear-view camera from the system, follow the steps below.
1. Turn ignion to ON.
2. Wait unl the headunit has completely booted and is in the home screen.
3. Make sure that the LEDs on the interface module is visible during this process. The LEDs are inside the module and are
visible through the side of the male 8-pin Molex connector.
4. Please observe the proper decoding sequence: First press and hold the HASH KEY/MODE buon then press and hold the
HANG UP buon. Connue to hold both buons and check if the RED and BLUE LEDs are blinking. The PCM system will
reset aer 5-10 seconds.
5. Release both buons.
6. The RED and BLUE LEDs will light up solid.
7. “Rear-View Camera” will no longer show on the radio menu opon aer a successful decoding.
PCM-3F
Rear & Front View Integration Interface
for Porsche Vehicles with PCM 3 & 3.1 Navigation Systems

Product specificaties

Merk: CRUX
Categorie: Niet gecategoriseerd
Model: PCM-3F

Heb je hulp nodig?

Als je hulp nodig hebt met CRUX PCM-3F stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd CRUX

CRUX

CRUX ACPLR-01 Handleiding

12 November 2024
CRUX

CRUX ACPMB-50W Handleiding

12 November 2024
CRUX

CRUX ACPBM-77Z Handleiding

12 November 2024
CRUX

CRUX ACPAD-81Y Handleiding

12 November 2024
CRUX

CRUX ACPAD-01 Handleiding

12 November 2024
CRUX

CRUX ACPBM-77X Handleiding

12 November 2024
CRUX

CRUX ACPLX-12XW Handleiding

12 November 2024
CRUX

CRUX ACPMB-45W Handleiding

12 November 2024
CRUX

CRUX ACPBM-77Y Handleiding

12 November 2024
CRUX

CRUX DKGM-16B Handleiding

5 November 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Kolcraft

Kolcraft MLB Chicago Cubs Handleiding

26 November 2024
Kolcraft

Kolcraft MLB New York Yankees Handleiding

26 November 2024
Kolcraft

Kolcraft MLB San Francisco Giants Handleiding

26 November 2024
Kolcraft

Kolcraft MLB St. Louis Cardinals Handleiding

26 November 2024
Nedis

Nedis POCO106 Handleiding

26 November 2024
Nedis

Nedis BTSM1GY Handleiding

26 November 2024
Turbosound

Turbosound TPOLEAJ-01 Handleiding

26 November 2024
Turbosound

Turbosound TSTAND-01 Handleiding

26 November 2024
IFM

IFM TAD981 Handleiding

26 November 2024
IFM

IFM TAD961 Handleiding

26 November 2024