CRUX DKGM-48S Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor CRUX DKGM-48S (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 5 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
- Retains factory features in select GM Class II Data Bus vehicles while functioning with an
aftermarket radio.
- Pre-programmed to retain factory Steering Wheel Controls.
- Voice Recognition Command from factory SWC.
- Supports Bose, Y-91 and non-amplified audio systems.
- Retains chime functions.
- Built-in chime volume adjustment.
- Single DIN Dash Kit included.
- EIA color coded wiring for easy installation.
GM- Module 48S
GM- Harness (GM-C2) 48S
SWC Cables
Single DIN Dash Kit
1. The Front and Rear fading are not retained on Y-91 Bose System.
2. Chime includes: seat belt, check engine, key in ignition, low fuel, low oil and lights on.
1 /8
rev.092821
SETTING THE AFTERMARKET RADIO BRAND
With the key in the off position, set the DIP switches to the corresponding radio listed below. See page 8 for SWC
button functions.
3.5MM SWC CABLE
The SWR - Module allows for both types of connections: GM 48S
OPTION A is used for ALPINE, CLARION, JVC, and KENWOOD units (Blue/Yellow wire is attached)
is used for ATOTO, BOSS, DUAL, FAHRENHEIT, JENSEN, PIONEER, POWER ACOUSTIK, SONY,OPTION B
SOUND STREAM and other Off-Brand headunits.
NOTE: Cap or insulate the 3.5mm plug or Blue/Yellow wire if not being used.
If the vehicle is equipped with a Bose system, the - has a built-in Bose adaptor that allows the proper audio DKGM 48S
input gain from the aftermarket radio to the Bose amplifier. To use this feature, plug in the male 8-pin connector on
the harness to the GRAY female 8-pin connector on the -48S GM module. The module is also labeled “Bose” and
“Non Bose” to avoid confusion. (see picture below)
If the vehicle is NOT equipped with a Bose system, plug in the male 8-pin connector to the BLACK female 8-pin on
the - module. GM 48S
2/8
BOSE
Connection
Non-BOSE
Connection
rev.092821
The - has a potentiometer to adjust the chime volume. It is set at half way by default. To adjust the DKGM 48S
volume, simply use a suitable screw driver and turn the potentiometer clockwise to increase the volume and
counter-clockwise to decrease the volume.
Please make sure that you have all the parts shown below.
3/8
rev.092821


Product specificaties

Merk: CRUX
Categorie: Niet gecategoriseerd
Model: DKGM-48S

Heb je hulp nodig?

Als je hulp nodig hebt met CRUX DKGM-48S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd CRUX

CRUX

CRUX ACPLR-01 Handleiding

12 November 2024
CRUX

CRUX ACPMB-50W Handleiding

12 November 2024
CRUX

CRUX ACPBM-77Z Handleiding

12 November 2024
CRUX

CRUX ACPAD-81Y Handleiding

12 November 2024
CRUX

CRUX ACPAD-01 Handleiding

12 November 2024
CRUX

CRUX ACPBM-77X Handleiding

12 November 2024
CRUX

CRUX ACPLX-12XW Handleiding

12 November 2024
CRUX

CRUX ACPMB-45W Handleiding

12 November 2024
CRUX

CRUX ACPBM-77Y Handleiding

12 November 2024
CRUX

CRUX DKGM-16B Handleiding

5 November 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Bogen

Bogen SPS2466 Handleiding

28 Februari 2025
Bogen

Bogen SPS2425 Handleiding

28 Februari 2025
Bogen

Bogen WB1EZ Handleiding

28 Februari 2025
Bogen

Bogen SM4T Handleiding

28 Februari 2025
Bogen

Bogen SI35A Handleiding

28 Februari 2025
Bogen

Bogen SPS2410 Handleiding

28 Februari 2025
Bogen

Bogen SLC Handleiding

28 Februari 2025